ina228 0.0.2__py3-none-any.whl

ina228/__init__.py

@@ -0,0 +1 @@
+from .api import INA228

ina228/api.py

@@ -0,0 +1,680 @@
+"""Driver for TI INA228 with SMBUS.
+
+Original code by @megalloid.
+Python module created by @makise_homura.
+
+Typical usage:
+
+    from ina228 import INA228
+    ina228 = INA228(bus, addr)
+    ina228.configure()
+    print('Voltage: ', ina228.get_vbus_voltage())
+    print('Current: ', ina228.get_current())
+    print('Power: ', ina228.get_power())
+
+Need to fix:
+    1) Value of VSHUHT is needed to multiply to 10 that get correct value.
+"""
+
+import time
+
+from smbus2 import SMBus
+
+from .testing import mock_SMBus
+
+# INA228 Address
+INA228_PORT = 1
+INA228_ADDRESS = 0x45
+INA228_SHUNT_OHMS = 0.025
+INA228_SHUNT_TEMPCO_VALUE = 0
+
+#############################################################
+# INA228 Reset bytes for CONFIG [15] / [14]
+# Decription: 
+# RST - Generates a system reset that is the same as power-on reset.
+# RSTACC - Resets the contents of accumulation registers ENERGY and CHARGE to 0
+#############################################################
+INA228_RST_NBIT = 15
+INA228_RSTACC_NBIT = 14
+
+#############################################################
+# INA228 Initial conversion delay CONFIG [13:6]
+# Description: Delay for initial ADC conversion in steps of 2 ms
+# Values:
+# 0x0 - 0 seconds (default)
+# 0x1 - 2 ms
+# 0xFF - 510ms
+#############################################################
+INA228_CONVERSION_DELAY = 0
+INA228_CONVDLY_NBIT = 6
+
+#############################################################
+# INA228 Temperature compensation CONFIG [5]
+# Description: Enables temperature compensation of an external shunt
+# Values:
+# 0x0 - disabled (default)
+# 0x1 - enabled
+#############################################################
+INA228_TEMP_COMP = 0
+INA228_TEMPCOMP_NBIT = 5
+
+#############################################################
+# INA228 ADC Shunt full scale range selection CONFIG [4]
+# Description: Shunt full scale range selection across IN+ and IN–.
+# Values:
+# 0x0 - ±163.84 mV (default)
+# 0x1 - ±40.96 mV
+#############################################################
+INA228_ADCRANGE = 0
+INA228_ADCRANGE_NBIT = 4
+
+#############################################################
+# INA228 ADC Mode
+# Description: The user can set the MODE bits for continuous or 
+# triggered mode on bus voltage, shunt voltage or temperature measurement.
+#
+# Values:
+# 0x0h = Shutdown
+# 0x1h = Triggered bus voltage, single shot
+# 0x2h = Triggered shunt voltage, single shot
+# 0x3h = Triggered shunt voltage and bus voltage, single shot
+# 0x4h = Triggered temperature, single shot
+# 0x5h = Triggered temperature and bus voltage, single shot
+# 0x6h = Triggered temperature and shunt voltage, single shot
+# 0x7h = Triggered bus voltage, shunt voltage and temperature, single shot
+# 0x8h = Shutdown
+# 0x9h = Continuous bus voltage only
+# 0xAh = Continuous shunt voltage only
+# 0xBh = Continuous shunt and bus voltage
+# 0xCh = Continuous temperature only
+# 0xDh = Continuous bus voltage and temperature
+# 0xEh = Continuous temperature and shunt voltage
+# 0xFh = Continuous bus voltage, shunt voltage and temperature (default)
+#############################################################
+INA228_ADC_MODE = 0xB
+INA228_ADC_MODE_NBIT = 12
+
+#############################################################
+# INA228 ADC conversion time of bus voltage meas.
+# Description: Sets the conversion time of the bus voltage measurement
+#
+# Values:
+# 0x00h = 50 μs
+# 0x01h = 84 μs
+# 0x02h = 150 μs
+# 0x03h = 280 μs
+# 0x04h = 540 μs
+# 0x05h = 1052 μs
+# 0x06h = 2074 μs
+# 0x07h = 4120 μs
+#############################################################
+INA228_VBUS_CONV_TIME = 0x05
+INA228_VBUS_CONV_TIME_NBIT = 0x09
+
+#############################################################
+# INA228 ADC conversion time of shunt voltage meas.
+# Description: Sets the conversion time of the shunt voltage measurement
+#
+# Values:
+# 0x00h = 50 μs
+# 0x01h = 84 μs
+# 0x02h = 150 μs
+# 0x03h = 280 μs
+# 0x04h = 540 μs
+# 0x05h = 1052 μs
+# 0x06h = 2074 μs
+# 0x07h = 4120 μs
+#############################################################
+INA228_VSHCT_CONV_TIME = 0x05
+INA228_VSHCT_CONV_TIME_NBIT = 0x06
+
+#############################################################
+# INA228 ADC conversion time of temperatrure meas.
+# Description: Sets the conversion time of the temperatrure measurement
+#
+# Values:
+# 0x00h = 50 μs
+# 0x01h = 84 μs
+# 0x02h = 150 μs
+# 0x03h = 280 μs
+# 0x04h = 540 μs
+# 0x05h = 1052 μs
+# 0x06h = 2074 μs
+# 0x07h = 4120 μs
+#############################################################
+INA228_VTCT_CONV_TIME = 0x05
+INA228_VTCT_CONV_TIME_NBIT = 0x03
+
+
+#############################################################
+# INA228 ADC sample averaging count. 
+#
+# Values: 
+# 0x0h = 1
+# 0x1h = 4
+# 0x2h = 16
+# 0x3h = 64
+# 0x4h = 128
+# 0x5h = 256
+# 0x6h = 512
+# 0x7h = 1024
+#############################################################
+INA228_ADC_AVG = 3
+INA228_AVG_NBIT = 0
+
+
+#############################################################
+# INA228 ADC alerts signal
+#############################################################
+INA228_ALERT_MEMSTAT = 0
+INA228_ALERT_CNVRF = 1
+INA228_ALERT_POL = 2
+INA228_ALERT_BUSUL = 3
+INA228_ALERT_BUSOL = 4
+INA228_ALERT_SHNTUL = 5
+INA228_ALERT_SHNTOL = 6
+INA228_ALERT_TMPOL = 7
+INA228_ALERT_MATHOF = 9
+INA228_ALERT_CHARGEOF = 10
+INA228_ALERT_ENERGYOF = 11
+INA228_ALERT_APOL = 12
+INA228_ALERT_SLOWALERT = 13
+INA228_ALERT_CNVR = 14
+INA228_ALERT_ALATCH = 15
+
+
+class INA228:
+    """Main INA228 interface"""
+
+    __INA228_CONFIG         = 0x00
+    __INA228_ADC_CONFIG     = 0x01
+    __INA228_SHUNT_CAL      = 0x02
+    __INA228_SHUNT_TEMPCO   = 0x03
+    __INA228_VSHUNT         = 0x04
+    __INA228_VBUS           = 0x05
+    __INA228_DIETEMP        = 0x06
+    __INA228_CURRENT        = 0x07
+    __INA228_POWER          = 0x08
+    __INA228_ENERGY         = 0x09
+    __INA228_CHARGE         = 0x0A
+    __INA228_DIAG_ALRT      = 0x0B
+    __INA228_SOVL           = 0x0C
+    __INA228_SUVL           = 0x0D
+    __INA228_BOVL           = 0x0E
+    __INA228_BUVL               = 0x0F
+    __INA228_TEMP_LIMIT         = 0x10
+    __INA228_PWR_LIMIT          = 0x11
+    __INA228_MANUFACTURER_ID    = 0x3E
+    __INA228_DEVICE_ID          = 0x3F
+
+    def __init__(self, busnum = INA228_PORT, address = INA228_ADDRESS, shunt_ohms = INA228_SHUNT_OHMS, stub_regmap = None):
+        """Creates INA228 instance.
+
+        Args:
+            busnum: SMBus bus number INA228 connected to.
+            address: SMBus slave address of INA228.
+            shunt_ohms: Shunt value for current measurements.
+            stub_regmap: Used in tests to emulate real INA228.
+
+        Returns:
+            Uninitialized INA228 instance linked to specific SMBus location.
+
+        Raises:
+            Any exception smbus2.SMBus() may raise.
+        """
+
+        self._address = address
+        self._i2c = mock_SMBus(stub_regmap) if stub_regmap else SMBus(busnum)
+        self._shunt_ohms = shunt_ohms
+        self._stub_regmap = stub_regmap
+
+    def __convert2comp2float(self, twocompdata, nrofbit, factor):
+
+        isnegative = 1
+        isnegative = (isnegative << (nrofbit - 1))
+
+        dietemp = twocompdata
+
+        if(dietemp > isnegative):
+            dietemp = (dietemp - (2*isnegative)) * factor
+        else:
+            dietemp = (dietemp * factor)
+
+        return dietemp
+
+
+    def __binary_as_string(self, register_value):
+
+        return bin(register_value)[2:].zfill(16)
+
+
+    def __to_bytes(self, register_value):
+
+        return [(register_value >> 8) & 0xFF, register_value & 0xFF]
+
+
+    def read_register40(self, register):
+
+        result = self._i2c.read_i2c_block_data(self._address, register, 5)
+
+        register_value = ((result[0] << 32) & 0xFF00000000) | ((result[1] << 24) & 0xFF000000) | ((result[2] << 16) & 0xFF0000) | ((result[3] << 8) & 0xFF00) | (result[4] & 0xFF)
+
+        #print("Read register 16 bits - 0x%02X: 0x%05X = 0b%s" %(register, register_value, self.__binary_as_string(register_value)))
+
+        return register_value
+
+
+    def read_register24(self, register):
+
+        result = self._i2c.read_i2c_block_data(self._address, register, 3)
+
+        register_value = ((result[0] << 16) & 0xFF0000) | ((result[1] << 8) & 0xFF00) | (result[2] & 0xFF)
+
+        #print("Read register 24 bits - 0x%02X: 0x%05X = 0b%s" %(register, register_value, self.__binary_as_string(register_value)))
+
+        return register_value
+
+
+    def read_register16(self, register):
+
+        result = self._i2c.read_i2c_block_data(self._address, register, 2)
+
+        register_value = ((result[0] << 8) & 0xFF00) | (result[1] & 0xFF)
+
+        #print("Read register 16 bits - 0x%02X: 0x%04X = 0b%s" %(register, register_value, self.__binary_as_string(register_value)))
+
+        return register_value
+
+
+    def write_register16(self, register, register_value):
+
+        register_bytes = self.__to_bytes(register_value)
+
+        #print("Write register 16 bits 0x%02X: 0x%02X 0b%s" % (register, register_value, self.__binary_as_string(register_value)))
+
+        self._i2c.write_i2c_block_data(self._address, register, register_bytes)
+
+        # self._i2c.write_word_data(self._address, register, register_value)
+
+
+    def get_current_lsb(self):
+
+        if(INA228_ADCRANGE == 0):
+            temp = 163.84e-3
+        else:
+            temp = 40.96e-3
+
+        current_lsb = (temp / INA228_SHUNT_OHMS) / 524288
+
+        return current_lsb
+
+
+    def get_shunt_conv_factor(self):
+
+        if(INA228_ADCRANGE == 0):
+            shunt_conv_factor = 1.25e-6
+        else:
+            shunt_conv_factor = 5.0e-6
+
+        return shunt_conv_factor
+
+
+    def reset_all(self):
+
+        config = self.read_register16(self.__INA228_CONFIG)
+
+        data = 1 << INA228_RST_NBIT
+
+        config = config | data
+
+        self.write_register16(self.__INA228_CONFIG, config)
+
+
+    def reset_energy(self):
+
+        config = self.read_register16(self.__INA228_CONFIG)
+
+        data = 1 << INA228_RSTACC_NBIT
+
+        config = config | data
+
+        self.write_register16(self.__INA228_CONFIG, config)
+
+
+    def set_config(self):
+
+        # Write settings to CONFIG register
+
+        config = self.read_register16(self. __INA228_CONFIG)
+
+        config = config | (INA228_CONVERSION_DELAY << INA228_CONVDLY_NBIT) | (INA228_TEMP_COMP << INA228_TEMPCOMP_NBIT) | (INA228_ADCRANGE << INA228_ADCRANGE_NBIT)
+
+        self.write_register16(self.__INA228_CONFIG, config)
+
+
+    def set_adc_config(self):
+
+        # Write settings to ADC CONFIG register
+
+        config = self.read_register16(self. __INA228_ADC_CONFIG)
+
+        config = config | (INA228_ADC_MODE << INA228_ADC_MODE_NBIT) | (INA228_VBUS_CONV_TIME << INA228_VBUS_CONV_TIME_NBIT ) | (INA228_VSHCT_CONV_TIME << INA228_VSHCT_CONV_TIME_NBIT) | (INA228_VTCT_CONV_TIME << INA228_VTCT_CONV_TIME_NBIT) | (INA228_ADC_AVG << INA228_AVG_NBIT)
+
+        self.write_register16(self.__INA228_ADC_CONFIG, config)
+
+    
+    def shunt_calib(self):
+
+        calib_value = int(13107.2e6 * self.get_current_lsb() * INA228_SHUNT_OHMS)
+
+        self.write_register16(self.__INA228_SHUNT_CAL, calib_value)
+
+    
+    def shunt_tempco(self):
+
+        self.write_register16(self.__INA228_SHUNT_TEMPCO, INA228_SHUNT_TEMPCO_VALUE)
+
+    
+    def configure(self):
+        """Performs initial INA228 configuration.
+
+        Always call this prior to get any data from INA228.
+        """
+
+        self.reset_all()
+
+        self.set_config()
+        self.set_adc_config()
+
+        self.shunt_calib()
+        self.shunt_tempco()
+
+        time.sleep(0.1)
+
+
+    def get_shunt_voltage(self):
+        """Read voltage on the shunt resistor.
+
+        Returns:
+            Voltage in volts.
+        """
+
+        if(INA228_ADCRANGE == 1):
+            conversion_factor = 312.5e-9                # nV/LSB
+        else:
+            conversion_factor = 78.125e-9               # nV/LSB  
+
+        raw = self.read_register24(self.__INA228_VSHUNT)
+
+        vshunt = (self.__convert2comp2float(raw >> 4, 20, conversion_factor)) * 10                  # Find and fix *10
+
+        return vshunt
+
+
+    def get_vbus_voltage(self):
+        """Read voltage on the V+/V- terminals.
+
+        Returns:
+            Voltage in volts.
+        """
+
+        conversion_factor = 195.3125e-6                 # uV/LSB
+
+        raw = self.read_register24(self.__INA228_VBUS)
+
+        vbus = self.__convert2comp2float(raw >> 4, 20, conversion_factor)
+
+        return vbus
+
+
+    def get_temp(self):
+        """Read die temperature.
+
+        Returns:
+            Temperature in Celsius.
+        """
+
+        conversion_factor = 7.8125e-3
+
+        raw = self.read_register16(self.__INA228_DIETEMP)
+
+        temp = self.__convert2comp2float(raw, 16, conversion_factor)
+
+        return temp
+
+
+    def get_current(self):
+        """Read current through I+/I- terminals.
+
+        Returns:
+            Current in amperes.
+        """
+
+        raw = self.read_register24(self.__INA228_CURRENT)
+
+        current = self.__convert2comp2float(raw >> 4, 20, self.get_current_lsb())
+
+        return current
+
+
+    def get_power(self):
+        """Read calculated power (a product of voltage and current).
+
+        Returns:
+            Power in watts.
+        """
+
+        current_lsb = self.get_current_lsb() 
+
+        raw = self.read_register24(self.__INA228_POWER)
+
+        power = (3.2 * raw * current_lsb)
+
+        return power
+
+
+    def get_energy(self):
+        """Read integral energy (a product of power and time).
+
+        Returns:
+            Energy in joules.
+        """
+
+        raw = self.read_register40(self.__INA228_ENERGY)
+
+        energy = raw * 3.2 * 16 * self.get_current_lsb()
+
+        return energy
+
+
+    def get_charge(self):
+        """Read charge spent (a product of current and time).
+
+        Returns:
+            Charge in coulombs.
+        """
+
+        raw = self.read_register40(self.__INA228_CHARGE)
+
+        return raw
+
+
+    def get_diag_alerts(self, alert):
+        """Read current through I+/I- terminals.
+
+        Args:
+            alert: Alert to read (any of INA228_ALERT_* constants).
+
+        Returns:
+            String representation of specific alert, or empty string if nothing to tell (e.g. no chosen alert).
+        """
+
+        raw = self.read_register16(self.__INA228_DIAG_ALRT)
+
+        if(alert == INA228_ALERT_ALATCH):
+            if (raw & 0x1) == 0x0:
+                return 'MEMSTAT: Checksum error is detected in the device trim memory space'
+
+        elif(alert == INA228_ALERT_CNVRF):
+            if (raw & 0x2) == 0x1:
+                return 'CNVRF: Conversion is completed'
+
+        elif(alert == INA228_ALERT_BUSUL):
+            if (raw & 0x4) == 0x1:
+                return 'BUSUL: Bus voltage measurement falls below the threshold limit in the bus under-limit register'
+
+        elif(alert == INA228_ALERT_BUSOL):
+            if (raw & 0x8) == 0x1:
+                return 'BUSOL: Bus voltage measurement exceeds the threshold limit in the bus over-limit register'
+
+        elif(alert == INA228_ALERT_SHNTUL):
+            if (raw & 0x10) == 0x1:
+                return 'SHNTUL: Shunt voltage measurement falls below the threshold limit in the shunt under-limit register'
+
+        elif(alert == INA228_ALERT_SHNTOL):
+            if (raw & 0x40) == 0x1:
+                return 'SHNTOL: Shunt voltage measurement exceeds the threshold limit in the shunt over-limit register'
+
+        elif(alert == INA228_ALERT_TMPOL):
+            if (raw & 0x80) == 0x1:
+                return 'TMPOL: Temperature measurement exceeds the threshold limit in the temperature over-limit register'
+
+        elif(alert == INA228_ALERT_MATHOF):
+            if (raw & 0x100) == 0x1:
+                return 'MATHOF: Arithmetic operation resulted in an overflow error'
+
+        elif(alert == INA228_ALERT_CHARGEOF):
+            if (raw & 0x200) == 0x1:
+                return 'CHARGEOF: 40 bit CHARGE register has overflowed'
+
+        elif(alert == INA228_ALERT_ENERGYOF):
+            if (raw & 0x400) == 0x1:
+                return 'ENERGYOF: 40 bit ENERGY register has overflowed'
+
+        elif(alert == INA228_ALERT_APOL):
+            if (raw & 0x800) == 0x1:
+                return 'APOL: Alert pin polarity inverted (active-high, open-drain)'
+            else:
+                return 'APOL: Alert pin polarity normale (active-low, open-drain)'
+
+        elif(alert == INA228_ALERT_SLOWALERT):
+            if (raw & 0x2000) == 0x1:
+                return 'SLOWALERT: ALERT function is asserted on the completed averaged value. ALERT comparison on averaged value'
+            else:
+                return 'SLOWALERT: ALERT comparison on non-averaged (ADC) value'
+
+        elif(alert == INA228_ALERT_CNVR):
+            if (raw & 0x4000) == 0x1:
+                return 'CNVR: Alert pin to be asserted when the Conversion Ready Flag (bit 1) is asserted, indicating that a conversion cycle has completed. Enables conversion ready flag on ALERT pin'
+            else:
+                return 'CNVR: Disable conversion ready flag on ALERT pin'
+
+        elif(alert == INA228_ALERT_ALATCH):
+            if (raw & 0x8000) == 0x1:
+                return 'ALATCH: Latched'
+            else:
+                return 'ALATCH: Transparent'
+
+        return ''
+
+
+    def set_shunt_overvoltage(self, value):
+
+        if (value >= 0):
+
+            data = (value * INA228_SHUNT_OHMS) / self.get_shunt_conv_factor()
+
+        else:
+
+            value_temp = value * (-1);
+
+            data = (value_temp * INA228_SHUNT_OHMS) / self.get_shunt_conv_factor()
+            data = ~data
+            data = data + 1
+
+        self.read_register16(self.__INA228_SOVL)
+
+        self.write_register16(self.__INA228_SOVL, data)
+
+
+    def set_shunt_undervoltage(self, value):
+
+        if (value >= 0):
+
+            data = (value * INA228_SHUNT_OHMS) / self.get_shunt_conv_factor()
+
+        else:
+
+            value_temp = value * (-1);
+
+            data = (value_temp * INA228_SHUNT_OHMS) / self.get_shunt_conv_factor()
+            data = ~data
+            data = data + 1
+
+        self.read_register16(self.__INA228_SUVL)
+
+        self.write_register16(self.__INA228_SUVL, data)
+
+
+    def set_bus_overvoltage(self, value):
+
+        data = value / (16 * 195.3125e-6)
+
+        self.read_register16(self.__INA228_BOVL)
+
+        self.write_register16(self.__INA228_BOVL, data)
+
+
+    def set_bus_undervoltage(self, value):
+
+        data = value / (16 * 195.3125e-6)
+
+        self.read_register16(self.__INA228_BUVL)
+
+        self.write_register16(self.__INA228_BUVL, data)
+
+
+    def set_temp_limit(self, value, consta):
+
+        data = value / (16 * consta)
+
+        self.read_register16(self.__INA228_TEMP_LIMIT)
+
+        self.write_register16(self.__INA228_TEMP_LIMIT, data)
+
+
+    def set_power_overlimit(self, value, consta):
+
+        data = value / (16 * consta)
+
+        self.read_register16(self.__INA228_PWR_LIMIT)
+
+        self.write_register16(self.__INA228_PWR_LIMIT, data)
+
+
+    def get_manufacturer_id(self):
+        """Read manufacturer ID.
+
+        Returns:
+            A tuple of (hex, char) manufacturer ID.
+        """
+
+        raw_id = self.read_register16(self.__INA228_MANUFACTURER_ID)
+
+        first_byte = (raw_id >> 8) & 0xFF
+        second_byte = (raw_id & 0xFF)
+
+        return (hex(raw_id), chr(first_byte),chr(second_byte))
+
+
+    def get_deviceid(self):
+        """Read device ID.
+
+        Returns:
+            A tuple of (device ID, device revision).
+        """
+
+        raw_id = self.read_register16(self.__INA228_DEVICE_ID)
+
+        return (hex(raw_id >> 4), hex(raw_id & 0xF))
+

ina228/testing.py

@@ -0,0 +1,12 @@
+class mock_SMBus:
+
+    def __init__(self, regmap):
+        self._regmap = regmap
+
+    def read_i2c_block_data(self, address, register, length):
+        assert(len(self._regmap[register]) == length)
+        return self._regmap[register]
+
+
+    def write_i2c_block_data(self, address, register, bytes):
+        pass

ina228-0.0.2.dist-info/LICENSE

@@ -0,0 +1,22 @@
+MIT License
+
+Copyright (c) 2021 Andrey Zaostrovnykh
+Copyright (c) 2026 Igor Molchanov
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in all
+copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+SOFTWARE.

ina228-0.0.2.dist-info/METADATA

@@ -0,0 +1,79 @@
+Metadata-Version: 2.2
+Name: ina228
+Version: 0.0.2
+Summary: Driver for TI INA228 with SMBUS
+Author-email: Andrey Zaostrovnykh <megalloid@gmail.com>, Igor Molchanov <akemi_homura@kurisa.ch>
+Maintainer-email: Igor Molchanov <akemi_homura@kurisa.ch>
+Project-URL: Repository, https://github.com/makise-homura/INA228/
+Project-URL: Issues, https://github.com/makise-homura/INA228/issues/
+Keywords: electronics,sensing,TI,home automation,smbus,ina2xx
+Classifier: Development Status :: 4 - Beta
+Classifier: Intended Audience :: Developers
+Classifier: Topic :: Home Automation
+Classifier: Programming Language :: Python :: 3
+Classifier: Programming Language :: Python :: 3.7
+Classifier: Programming Language :: Python :: 3.8
+Classifier: Programming Language :: Python :: 3.9
+Classifier: Programming Language :: Python :: 3.10
+Classifier: Programming Language :: Python :: 3.11
+Classifier: Programming Language :: Python :: 3.12
+Classifier: Programming Language :: Python :: 3.13
+Classifier: Programming Language :: Python :: 3.14
+Classifier: Programming Language :: Python :: 3.15
+Classifier: Operating System :: OS Independent
+Requires-Python: >=3.7
+Description-Content-Type: text/markdown
+License-File: LICENSE
+Requires-Dist: smbus2
+
+# INA228
+Driver for TI INA228 with SMBUS
+
+## Building
+
+Just run:
+
+```
+python3 -m build
+```
+
+## Requirements
+
+For now, it relies on `smbus2` module.
+
+## Testing
+
+After building the package, create venv:
+
+```
+python3 -m venv .venv
+```
+
+Install the module:
+
+```
+.venv/bin/pip install dist/ina228-*.whl --force-reinstall
+```
+
+Run the test:
+
+```
+.venv/bin/python tests/test.py
+```
+
+Test will use supplied `stub_regmap.py`, not the real INA228.
+If you want your own one, generate it by running `./map.sh > stub_regmap.py` on the system with live INA228.
+You may need to edit bus number and slave address in `map.sh` though.
+And remember to install `i2cget` with something like `apt install i2c-tools` prior to running this.
+
+If you want to use pytest, install it into venv:
+
+```
+.venv/bin/pip install pytest
+```
+
+And then run:
+
+```
+.venv/bin/python -m pytest
+```

ina228-0.0.2.dist-info/RECORD

@@ -0,0 +1,8 @@
+ina228/__init__.py,sha256=8JLgIWJkB54nnPLreEUfPYPPks_-AwulLe5go8a09j4,24
+ina228/api.py,sha256=8Lda-3PTBin8inFLw7m56FCwlhTQVQlFva5Owyf-OO8,19457
+ina228/testing.py,sha256=kf_aPoTSo_-371ogILU2K676osttf1dGUr32JgM7bdQ,313
+ina228-0.0.2.dist-info/LICENSE,sha256=ova-szagjnCitj5xXKMqZKu2qP2_5akEGbKJItdkw_w,1110
+ina228-0.0.2.dist-info/METADATA,sha256=QYqm-gBjesh1wiPbQIdU2qXqqsGKmGDR0MuAPwRsmps,2083
+ina228-0.0.2.dist-info/WHEEL,sha256=In9FTNxeP60KnTkGw7wk6mJPYd_dQSjEZmXdBdMCI-8,91
+ina228-0.0.2.dist-info/top_level.txt,sha256=g1ytYWUNG8uzFE-bxtmQp8LBYNGILASOvmhdQ_fh6As,7
+ina228-0.0.2.dist-info/RECORD,,

ina228-0.0.2.dist-info/WHEEL

@@ -0,0 +1,5 @@
+Wheel-Version: 1.0
+Generator: setuptools (75.8.0)
+Root-Is-Purelib: true
+Tag: py3-none-any
+

ina228-0.0.2.dist-info/top_level.txt

@@ -0,0 +1 @@
+ina228