three-slicer 0.1.6 → 0.2.0

package/data/config-schema.json

@@ -12944,5 +12944,703 @@
   "max": 18,
   "mode": "simple",
   "nullable": true
+ },
+ "branchingsupport_head_front_diameter": {
+  "type": "coFloat",
+  "mode": "advanced",
+  "defined_in": "init_sla_support_params",
+  "line": 4157,
+  "label": "Pinhead front diameter",
+  "category": "Supports",
+  "tooltip": "Diameter of the pointing side of the head",
+  "sidetext": "mm",
+  "min": 0,
+  "default_type": "Float",
+  "default_raw": "0.4",
+  "default": 0.4
+ },
+ "branchingsupport_head_penetration": {
+  "type": "coFloat",
+  "mode": "advanced",
+  "defined_in": "init_sla_support_params",
+  "line": 4166,
+  "label": "Head penetration",
+  "category": "Supports",
+  "tooltip": "How much the pinhead has to penetrate the model surface",
+  "sidetext": "mm",
+  "min": 0,
+  "default_type": "Float",
+  "default_raw": "0.2",
+  "default": 0.2
+ },
+ "branchingsupport_head_width": {
+  "type": "coFloat",
+  "mode": "advanced",
+  "defined_in": "init_sla_support_params",
+  "line": 4175,
+  "label": "Pinhead width",
+  "category": "Supports",
+  "tooltip": "Width from the back sphere center to the front sphere center",
+  "sidetext": "mm",
+  "min": 0,
+  "max": 20,
+  "default_type": "Float",
+  "default_raw": "1.0",
+  "default": 1.0
+ },
+ "branchingsupport_pillar_diameter": {
+  "type": "coFloat",
+  "mode": "simple",
+  "defined_in": "init_sla_support_params",
+  "line": 4185,
+  "label": "Pillar diameter",
+  "category": "Supports",
+  "tooltip": "Diameter in mm of the support pillars",
+  "sidetext": "mm",
+  "min": 0,
+  "max": 15,
+  "default_type": "Float",
+  "default_raw": "1.0",
+  "default": 1.0
+ },
+ "branchingsupport_small_pillar_diameter_percent": {
+  "type": "coPercent",
+  "mode": "expert",
+  "defined_in": "init_sla_support_params",
+  "line": 4195,
+  "label": "Small pillar diameter percent",
+  "category": "Supports",
+  "tooltip": "The percentage of smaller pillars compared to the normal pillar diameter which are used in problematic areas where a normal pilla cannot fit.",
+  "sidetext": "%",
+  "min": 1,
+  "max": 100,
+  "default_type": "Percent",
+  "default_raw": "50",
+  "default": 50
+ },
+ "branchingsupport_max_bridges_on_pillar": {
+  "type": "coInt",
+  "mode": "expert",
+  "defined_in": "init_sla_support_params",
+  "line": 4206,
+  "label": "Max bridges on a pillar",
+  "tooltip": "Maximum number of bridges that can be placed on a pillar. Bridges hold support point pinheads and connect to pillars as small branches.",
+  "min": 0,
+  "max": 50,
+  "default_type": "Int",
+  "default_raw": "prefix == \"branching\" ? 2 : 3"
+ },
+ "support_max_weight_on_model": {
+  "type": "coFloat",
+  "mode": "expert",
+  "defined_in": "init_sla_support_params",
+  "line": 4216,
+  "label": "Max weight on model",
+  "category": "Supports",
+  "tooltip": "Maximum weight of sub-trees that terminate on the model instead of the print bed. The weight is the sum of the lenghts of all branches emanating from the endpoint.",
+  "sidetext": "mm",
+  "min": 0,
+  "default_type": "Float",
+  "default_raw": "10.",
+  "default": 10.0
+ },
+ "branchingsupport_max_weight_on_model": {
+  "type": "coFloat",
+  "mode": "expert",
+  "defined_in": "init_sla_support_params",
+  "line": 4216,
+  "label": "Max weight on model",
+  "category": "Supports",
+  "tooltip": "Maximum weight of sub-trees that terminate on the model instead of the print bed. The weight is the sum of the lenghts of all branches emanating from the endpoint.",
+  "sidetext": "mm",
+  "min": 0,
+  "default_type": "Float",
+  "default_raw": "10.",
+  "default": 10.0
+ },
+ "branchingsupport_pillar_connection_mode": {
+  "type": "coEnum",
+  "mode": "advanced",
+  "defined_in": "init_sla_support_params",
+  "line": 4227,
+  "label": "Pillar connection mode",
+  "tooltip": "Controls the bridge type between two neighboring pillars. Can be zig-zag, cross (double zig-zag) or dynamic which will automatically switch between the first two depending on the distance of the two pillars.",
+  "default_type": "Enum",
+  "default_raw": "SLAPillarConnectionMode::dynamic"
+ },
+ "branchingsupport_buildplate_only": {
+  "type": "coBool",
+  "mode": "simple",
+  "defined_in": "init_sla_support_params",
+  "line": 4239,
+  "label": "Support on build plate only",
+  "category": "Supports",
+  "tooltip": "Only create support if it lies on a build plate. Don't create support on a print.",
+  "default_type": "Bool",
+  "default_raw": "false",
+  "default": false
+ },
+ "branchingsupport_pillar_widening_factor": {
+  "type": "coFloat",
+  "mode": "expert",
+  "defined_in": "init_sla_support_params",
+  "line": 4246,
+  "label": "Pillar widening factor",
+  "category": "Supports",
+  "tooltip": "Merging bridges or pillars into another pillars can increase the radius. Zero means no increase, one means full increase. The exact amount of increase is unspecified and can change in the future.",
+  "min": 0,
+  "max": 1,
+  "default_type": "Float",
+  "default_raw": "0.5",
+  "default": 0.5
+ },
+ "branchingsupport_base_diameter": {
+  "type": "coFloat",
+  "mode": "advanced",
+  "defined_in": "init_sla_support_params",
+  "line": 4261,
+  "label": "Support base diameter",
+  "category": "Supports",
+  "tooltip": "Diameter in mm of the pillar base",
+  "sidetext": "mm",
+  "min": 0,
+  "max": 30,
+  "default_type": "Float",
+  "default_raw": "4.0",
+  "default": 4.0
+ },
+ "branchingsupport_base_height": {
+  "type": "coFloat",
+  "mode": "advanced",
+  "defined_in": "init_sla_support_params",
+  "line": 4271,
+  "label": "Support base height",
+  "category": "Supports",
+  "tooltip": "The height of the pillar base cone",
+  "sidetext": "mm",
+  "min": 0,
+  "default_type": "Float",
+  "default_raw": "1.0",
+  "default": 1.0
+ },
+ "branchingsupport_base_safety_distance": {
+  "type": "coFloat",
+  "mode": "expert",
+  "defined_in": "init_sla_support_params",
+  "line": 4280,
+  "label": "Support base safety distance",
+  "category": "Supports",
+  "tooltip": "The minimum distance of the pillar base from the model in mm. Makes sense in zero elevation mode where a gap according to this parameter is inserted between the model and the pad.",
+  "sidetext": "mm",
+  "min": 0,
+  "max": 10,
+  "default_type": "Float",
+  "default_raw": "1",
+  "default": 1
+ },
+ "branchingsupport_critical_angle": {
+  "type": "coFloat",
+  "mode": "expert",
+  "defined_in": "init_sla_support_params",
+  "line": 4293,
+  "label": "Critical angle",
+  "category": "Supports",
+  "tooltip": "The default angle for connecting support sticks and junctions.",
+  "sidetext": "°",
+  "min": 0,
+  "max": 90,
+  "default_type": "Float",
+  "default_raw": "45",
+  "default": 45
+ },
+ "branchingsupport_max_bridge_length": {
+  "type": "coFloat",
+  "mode": "advanced",
+  "defined_in": "init_sla_support_params",
+  "line": 4303,
+  "label": "Max bridge length",
+  "category": "Supports",
+  "tooltip": "The max length of a bridge",
+  "sidetext": "mm",
+  "min": 0,
+  "default_type": "Float",
+  "default_raw": "default_val"
+ },
+ "branchingsupport_max_pillar_link_distance": {
+  "type": "coFloat",
+  "mode": "advanced",
+  "defined_in": "init_sla_support_params",
+  "line": 4317,
+  "label": "Max pillar linking distance",
+  "category": "Supports",
+  "tooltip": "The max distance of two pillars to get linked with each other. A zero value will prohibit pillar cascading.",
+  "sidetext": "mm",
+  "min": 0,
+  "default_type": "Float",
+  "default_raw": "10.0",
+  "default": 10.0
+ },
+ "branchingsupport_object_elevation": {
+  "type": "coFloat",
+  "mode": "advanced",
+  "defined_in": "init_sla_support_params",
+  "line": 4327,
+  "label": "Object elevation",
+  "category": "Supports",
+  "tooltip": "How much the supports should lift up the supported object. If \"Pad around object\" is enabled, this value is ignored.",
+  "sidetext": "mm",
+  "min": 0,
+  "max": 150,
+  "default_type": "Float",
+  "default_raw": "5.0",
+  "default": 5.0
+ },
+ "high_viscosity_tilt_time": {
+  "type": "coFloat",
+  "mode": "expert",
+  "defined_in": "init_sla_params",
+  "line": 4418,
+  "label": "High viscosity",
+  "full_label": "Tilt for high viscosity resin",
+  "tooltip": "Time of the super slow tilt",
+  "sidetext": "s",
+  "min": 0,
+  "default_type": "Float",
+  "default_raw": "10.",
+  "default": 10.0
+ },
+ "printing_temperature": {
+  "type": "coInt",
+  "mode": "advanced",
+  "defined_in": "init_sla_params",
+  "line": 4437,
+  "label": "Printing temperature",
+  "tooltip": "This value sets the target printing temperature. The printer will wait for the resin to reach this stable temperature before starting and will maintain it throughout the print. When disabled, the printer ignores the resin's current temperature and begins printing immediately.",
+  "sidetext": "°C",
+  "min": 18,
+  "max": 60,
+  "default_type": "IntNullable",
+  "default_raw": "ConfigOptionIntNullable::nil_value()"
+ },
+ "zcorrection_layers": {
+  "type": "coInt",
+  "mode": "advanced",
+  "defined_in": "init_sla_params",
+  "line": 4498,
+  "label": "Z compensation",
+  "category": "Advanced",
+  "tooltip": "Number of layers to Z correct to avoid cross layer bleed",
+  "min": 0,
+  "default_type": "Int",
+  "default_raw": "0",
+  "default": 0
+ },
+ "material_uuid": {
+  "type": "coString",
+  "mode": "simple",
+  "defined_in": "init_sla_params",
+  "line": 4579,
+  "label": "Material UUID (FOR DEBUGGING ONLY)",
+  "default_type": "String",
+  "default_raw": "\"\"",
+  "default": ""
+ },
+ "material_notes": {
+  "type": "coString",
+  "mode": "simple",
+  "defined_in": "init_sla_params",
+  "line": 4665,
+  "label": "SLA print material notes",
+  "tooltip": "You can put your notes regarding the SLA print material here.",
+  "multiline": true,
+  "full_width": true,
+  "height": 13,
+  "default_type": "String",
+  "default_raw": "\"\"",
+  "default": ""
+ },
+ "support_tree_type": {
+  "type": "coEnum",
+  "mode": "simple",
+  "defined_in": "init_sla_params",
+  "line": 4709,
+  "label": "Support tree type",
+  "tooltip": "Support tree building strategy",
+  "default_type": "Enum",
+  "default_raw": "sla::SupportTreeType::Default"
+ },
+ "support_enforcers_only": {
+  "type": "coBool",
+  "mode": "simple",
+  "defined_in": "init_sla_params",
+  "line": 4724,
+  "label": "Support only in enforced regions",
+  "category": "Supports",
+  "tooltip": "Only create support if it lies in a support enforcer.",
+  "default_type": "Bool",
+  "default_raw": "false",
+  "default": false
+ },
+ "sla_archive_format": {
+  "type": "coString",
+  "mode": "advanced",
+  "defined_in": "init_sla_params",
+  "line": 4921,
+  "label": "Format of the output SLA archive",
+  "default_type": "String",
+  "default_raw": "\"SL1\"",
+  "default": "SL1"
+ },
+ "sla_output_precision": {
+  "type": "coFloat",
+  "mode": "it_opt->second.mode",
+  "defined_in": "init_sla_params",
+  "line": 4926,
+  "label": "it_opt->second.label",
+  "tooltip": "it_opt->second.tooltip",
+  "sidetext": "it_opt->second.sidetext",
+  "min": "it_opt->second.min",
+  "default_type": "Float",
+  "default_raw": "0.001",
+  "default": 0.001,
+  "full_label": "it_opt->second.full_label",
+  "max": "it_opt->second.max"
+ },
+ "delay_before_exposure": {
+  "type": "coFloats",
+  "mode": "advanced",
+  "defined_in": "init_sla_tilt_params",
+  "line": 4977,
+  "full_label": "Delay before exposure",
+  "tooltip": "Sets a fixed pause before an exposure of the new layer starts. This setting is ignored if 'Dynamic delay before exposure' is enabled.",
+  "sidetext": "s",
+  "min": 0,
+  "max": 300,
+  "default_type": "Floats",
+  "default_raw": "{ 3., 3.}",
+  "default": [
+   3.0,
+   3.0
+  ]
+ },
+ "delay_after_exposure": {
+  "type": "coFloats",
+  "mode": "advanced",
+  "defined_in": "init_sla_tilt_params",
+  "line": 4987,
+  "full_label": "Delay after exposure",
+  "tooltip": "Delay after exposure before layer separation.",
+  "sidetext": "s",
+  "min": 0,
+  "max": 30,
+  "default_type": "Floats",
+  "default_raw": "{ 0., 0.}",
+  "default": [
+   0.0,
+   0.0
+  ]
+ },
+ "delay_to_reflood": {
+  "type": "coFloats",
+  "mode": "advanced",
+  "defined_in": "init_sla_tilt_params",
+  "line": 4996,
+  "full_label": "Delay to reflood",
+  "tooltip": "Defines the pause between the separation movement (tilt down, Z-hop) and the return movement (tilt up). Increasing this time allows the resin more time to fully reflood the peeled-off layer.",
+  "sidetext": "s",
+  "min": 0,
+  "max": 300,
+  "default_type": "Floats",
+  "default_raw": "{ 0., 0.}",
+  "default": [
+   0.0,
+   0.0
+  ]
+ },
+ "tower_hop_height": {
+  "type": "coFloats",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5006,
+  "full_label": "Tower hop height",
+  "tooltip": "An alternative separation move to tilting. After layer exposure, the platform lifts by this distance. A minimum of 5mm is recommended if tilting is disabled. If you use tilting, we suggest 0mm, although a combination of both is possible.",
+  "sidetext": "mm",
+  "min": 0,
+  "max": 100,
+  "default_type": "Floats",
+  "default_raw": "{ 0., 0.}",
+  "default": [
+   0.0,
+   0.0
+  ]
+ },
+ "tower_speed": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5017,
+  "full_label": "Tower speed",
+  "tooltip": "Tower speed used for tower raise.",
+  "sidetext": "mm/s"
+ },
+ "tilt_down_initial_speed": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5082,
+  "full_label": "Tilt down initial speed",
+  "tooltip": "Sets the initial speed for the tilt-down separation move. A high speed may negatively affect print quality or success, especially with certain resins or delicate geometries, but it speeds up the overall print time.",
+  "sidetext": "μ-steps/s"
+ },
+ "tilt_down_finish_speed": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5092,
+  "full_label": "Tilt down finish speed",
+  "tooltip": "Sets the final speed for the tilt-down separation move. Too high a speed, especially with less viscous resins, can cause resin to splash out of the tank.",
+  "sidetext": "μ-steps/s"
+ },
+ "tilt_up_initial_speed": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5101,
+  "full_label": "Tilt up initial speed",
+  "tooltip": "Sets the initial speed for the tilt-up return movement.",
+  "sidetext": "μ-steps/s"
+ },
+ "tilt_up_finish_speed": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5109,
+  "full_label": "Tilt up finish speed",
+  "tooltip": "Sets the final speed for the tilt-up return movement. Excessive speed, especially with highly viscous resins, can lead to a loss of print quality, or in extreme cases, tilt motor skipping or damage to the print display.",
+  "sidetext": "μ-steps/s"
+ },
+ "tilt_down_initial_speed_slx": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5119,
+  "full_label": "Tilt down initial speed",
+  "tooltip": "Tilt speed used for an initial portion of tilt down move.",
+  "sidetext": "μ-steps/s"
+ },
+ "tilt_down_finish_speed_slx": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5127,
+  "full_label": "Tilt down finish speed",
+  "tooltip": "Tilt speed used for the rest of the tilt down move.",
+  "sidetext": "μ-steps/s"
+ },
+ "tilt_up_initial_speed_slx": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5135,
+  "full_label": "Tilt up initial speed",
+  "tooltip": "Tilt speed used for an initial portion of tilt up move.",
+  "sidetext": "μ-steps/s"
+ },
+ "tilt_up_finish_speed_slx": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5143,
+  "full_label": "Tilt up finish speed",
+  "tooltip": "Tilt speed used for the rest of the tilt-up.",
+  "sidetext": "μ-steps/s"
+ },
+ "dynamic_delay_before_profile": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5151,
+  "full_label": "Dynamic delay before profile",
+  "tooltip": "Switches between predefined algorithms that influence how the dynamic delay before exposure function behaves."
+ },
+ "dynamic_delay_before_timeout": {
+  "type": "coFloats",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5158,
+  "full_label": "Dynamic delay before exposure timeout",
+  "tooltip": "Sets the maximum allowed time for waiting for the pressure sensors to stabilize during dynamic delay before exposure. Once this timeout expires, the printer starts exposing the next layer regardless of resin pressure stabilization.",
+  "min": 0,
+  "max": 120,
+  "default_type": "Floats",
+  "default_raw": "50., 50.",
+  "default": [
+   50.0,
+   50.0
+  ]
+ },
+ "dynamic_tilt_up_profile": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5167,
+  "full_label": "Dynamic tilt up profile",
+  "tooltip": "Switches between predefined algorithms that influence how the dynamic tilt up function behaves."
+ },
+ "dynamic_tilt_down_profile": {
+  "type": "coEnums",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5174,
+  "full_label": "Dynamic tilt down profile",
+  "tooltip": "Switches between predefined algorithms that influence how the dynamic tilt down function behaves."
+ },
+ "use_tilt": {
+  "type": "coBools",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5181,
+  "full_label": "Use tilt",
+  "tooltip": "Enables or disables the tilting function. If disabled, the layer separation is performed using the 'Tower hop height' parameter.",
+  "default_type": "Bools",
+  "default_raw": "{ true, true }",
+  "default": [
+   true,
+   true
+  ]
+ },
+ "tilt_down_offset_steps": {
+  "type": "coInts",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5187,
+  "full_label": "Tilt down offset steps",
+  "tooltip": "Defines the distance (steps) over which the 'Tilt down initial speed' is applied. Once this distance is covered, the tilt moves at the 'Tilt down finish speed'. Setting to 0 immediately applies the finish speed. Maximum distance varies by printer, typically around 12,000 steps.",
+  "sidetext": "μ-steps",
+  "min": 0,
+  "max": 10000,
+  "default_type": "Ints",
+  "default_raw": "{ 0, 0 }",
+  "default": [
+   0,
+   0
+  ]
+ },
+ "tilt_down_offset_delay": {
+  "type": "coFloats",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5198,
+  "full_label": "Tilt down offset delay",
+  "tooltip": "Delay after the tilt reaches 'tilt_down_offset_steps' position.",
+  "sidetext": "s",
+  "min": 0,
+  "max": 20,
+  "default_type": "Floats",
+  "default_raw": "{ 0., 0. }",
+  "default": [
+   0.0,
+   0.0
+  ]
+ },
+ "tilt_down_cycles": {
+  "type": "coInts",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5207,
+  "full_label": "Tilt down cycles",
+  "tooltip": "Number of cycles to split the rest of the tilt down move.",
+  "min": 0,
+  "max": 10,
+  "default_type": "Ints",
+  "default_raw": "{ 1, 1 }",
+  "default": [
+   1,
+   1
+  ]
+ },
+ "tilt_down_delay": {
+  "type": "coFloats",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5215,
+  "full_label": "Tilt down delay",
+  "tooltip": "The delay between tilt-down cycles.",
+  "sidetext": "s",
+  "min": 0,
+  "max": 20,
+  "default_type": "Floats",
+  "default_raw": "{ 0., 0. }",
+  "default": [
+   0.0,
+   0.0
+  ]
+ },
+ "tilt_up_offset_steps": {
+  "type": "coInts",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5224,
+  "full_label": "Tilt up offset steps",
+  "tooltip": "Defines the distance over which the 'Tilt up initial speed' is applied. After this distance, the tilt moves at the 'Tilt up finish speed'. Setting to 0 immediately applies the finish speed.",
+  "sidetext": "μ-steps",
+  "min": 0,
+  "max": 10000,
+  "default_type": "Ints",
+  "default_raw": "{ 1200, 1200 }",
+  "default": [
+   1200,
+   1200
+  ]
+ },
+ "tilt_up_offset_delay": {
+  "type": "coFloats",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5234,
+  "full_label": "Tilt up offset delay",
+  "tooltip": "Delay after the tilt reaches 'tilt_up_offset_steps' position.",
+  "sidetext": "s",
+  "min": 0,
+  "max": 20,
+  "default_type": "Floats",
+  "default_raw": "{ 0., 0. }",
+  "default": [
+   0.0,
+   0.0
+  ]
+ },
+ "tilt_up_cycles": {
+  "type": "coInts",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5243,
+  "full_label": "Tilt up cycles",
+  "tooltip": "Number of cycles to split the rest of the tilt-up.",
+  "min": 0,
+  "max": 10,
+  "default_type": "Ints",
+  "default_raw": "{ 1, 1 }",
+  "default": [
+   1,
+   1
+  ]
+ },
+ "tilt_up_delay": {
+  "type": "coFloats",
+  "mode": "expert",
+  "defined_in": "init_sla_tilt_params",
+  "line": 5251,
+  "full_label": "Tilt up delay",
+  "tooltip": "The delay between tilt-up cycles.",
+  "sidetext": "s",
+  "min": 0,
+  "max": 20,
+  "default_type": "Floats",
+  "default_raw": "{ 0., 0. }",
+  "default": [
+   0.0,
+   0.0
+  ]
  }
 }