ocs-calculators 0.2.0 → 0.2.2

package/CHANGELOG.md

@@ -3,6 +3,31 @@
 本文件格式遵循 [Keep a Changelog](https://keepachangelog.com/zh-CN/1.1.0/)，
 版本号遵循[语义化版本](https://semver.org/lang/zh-CN/)。
 
+## [0.2.2] - 2026-09-15
+
+### 修复
+
+- **输入防护补齐**：`sag` 的 `maxSpanFromSagM` 对张力/单位重非正值抛 `RangeError`
+  （此前 0 或负数会静默返回 `0` / `NaN` / `Infinity`）；`pole-capacity` 的
+  `poleCapacityCheck` 对零跨距抛 `RangeError`（此前除零静默返回 `Infinity`）
+- `creepage` 移除比距三档折算中的等值分支死代码（行为不变，统一取档位下限折算）
+
+## [0.2.1] - 2026-09-14
+
+### 修复
+
+- **子路径导出回归**：v0.2.0 新增 8 个模块的 `exports` 键缺 `./` 前缀，
+  子路径导入（如 `ocs-calculators/steady-arm`）全部抛
+  `ERR_PACKAGE_PATH_NOT_EXPORTED`，已逐键修正
+
+## [0.2.0] - 2026-09-14
+
+### 新增
+
+- **8 个新计算器模块**：steady-arm（定位器坡度）、cross-span（软横跨负载）、
+  bvalue（坠砣高度）、sag（弛度）、anchor-length（锚段校核）、creepage（爬电选型）、
+  pole-capacity（支柱容量）、cantilever（腕臂预配），共 20 模块 212 测试
+
 ## [0.1.3] - 2026-09-07
 
 ### 修复

package/README.md

@@ -29,6 +29,8 @@
 npm install ocs-calculators
 ```
 
+> ⚠️ **请使用 ≥ 0.2.1**。`0.2.0` 曾因子路径 exports 键写错（缺少 `./` 前缀）导致 `import 'ocs-calculators'` 报 `ERR_INVALID_PACKAGE_CONFIG`，已由 `0.2.1` 修复。裸 `npm install ocs-calculators` 会取 latest（0.2.1），无需特殊处理；若你的依赖显式锁了 `@0.2.0`，请升级到 `@0.2.1`。
+
 ## 快速开始
 
 ```ts
@@ -67,11 +69,19 @@ for (const p of curve) {
 ```ts
 import { windClearanceCheck } from 'ocs-calculators/wind';
 import { wearRatio } from 'ocs-calculators/wear';
+import { steadyArmAngleDeg } from 'ocs-calculators/steady-arm';
+import { crossSpanAnalyze } from 'ocs-calculators/cross-span';
+import { bValue } from 'ocs-calculators/bvalue';
+import { sagMM } from 'ocs-calculators/sag';
+import { anchorLengthCheck } from 'ocs-calculators/anchor-length';
+import { creepageCheck } from 'ocs-calculators/creepage';
+import { poleCapacityCheck } from 'ocs-calculators/pole-capacity';
+import { cantileverCut } from 'ocs-calculators/cantilever';
 ```
 
-## 12 个计算器（全部实现）
+## 20 个计算器（全部实现）
 
-对应 <https://www.itswe.com/Category:tools> 的 12 个在线计算器，全部已实现并逐项回归。
+对应 <https://www.itswe.com/Category:tools> 的 20 个在线计算器，全部已实现并逐项回归。
 
 | 状态 | 计算器 | 模块 | 在线地址 |
 |---|---|---|---|
@@ -87,9 +97,17 @@ import { wearRatio } from 'ocs-calculators/wear';
 | ✅ 已实现 | 电压降校核 | `voltage-drop` | [/calculator/voltage-drop/](https://www.itswe.com/calculator/voltage-drop/) |
 | ✅ 已实现 | 曲线拉出值校核 | `curve-stagger` | [/calculator/curve-stagger/](https://www.itswe.com/calculator/curve-stagger/) |
 | ✅ 已实现 | 覆冰荷载校核 | `icing` | [/calculator/icing/](https://www.itswe.com/calculator/icing/) |
-
-所有公式与默认参数均取自站点 `/calculator/assets/calc-core.js` 源码，
-单元测试的期望值由源码公式独立算出，未从渲染结果反推。
+| ✅ 已实现 | 弛度速算 | `sag` | [/calculator/sag/](https://www.itswe.com/calculator/sag/) |
+| ✅ 已实现 | b 值（坠砣高度）安装曲线 | `bvalue` | [/calculator/bvalue/](https://www.itswe.com/calculator/bvalue/) |
+| ✅ 已实现 | 绝缘子爬电距离选型校核 | `creepage` | [/calculator/creepage/](https://www.itswe.com/calculator/creepage/) |
+| ✅ 已实现 | 锚段长度张力差校核 | `anchor-length` | [/calculator/anchor-length/](https://www.itswe.com/calculator/anchor-length/) |
+| ✅ 已实现 | 定位器坡度校核 | `steady-arm` | [/calculator/steady-arm/](https://www.itswe.com/calculator/steady-arm/) |
+| ✅ 已实现 | 软横跨负载计算 | `cross-span` | [/calculator/cross-span/](https://www.itswe.com/calculator/cross-span/) |
+| ✅ 已实现 | 支柱容量选型校核 | `pole-capacity` | [/calculator/pole-capacity/](https://www.itswe.com/calculator/pole-capacity/) |
+| ✅ 已实现 | 腕臂预配（勾股下料） | `cantilever` | [/calculator/cantilever/](https://www.itswe.com/calculator/cantilever/) |
+
+原 12 个模块的公式与默认参数取自站点 `/calculator/assets/calc-core.js` 源码；
+新增的 8 个模块（sag/bvalue/creepage/anchor-length/steady-arm/cross-span/pole-capacity/cantilever）为站点**内联引擎计算器**（引擎直嵌页面 HTML，不经 calc-core），本仓库按其 online 页面公式提炼，单元测试期望值由公式独立算出，未从服务器渲染结果反推。
 
 ## 单位约定
 
@@ -118,15 +136,15 @@ console.log(tensionMeta.disclaimer);  // 免责声明
 
 ## 与站点实现的同步政策
 
-本仓库是 [itswe.com](https://www.itswe.com) 在线计算器的公式算法层，同步基准为站点资产
-[`calculator/assets/calc-core.js`](https://www.itswe.com/calculator/assets/calc-core.js)：
+本仓库是 [itswe.com](https://www.itswe.com) 在线计算器的公式算法层，同步基准为站点资产：
 
-- `src/` 中每个模块的公式与默认参数，以 `calc-core.js` 对应实现为准；
+- 原 12 个模块以 [`calculator/assets/calc-core.js`](https://www.itswe.com/calculator/assets/calc-core.js) 为准；
+- 新增 8 个模块（`sag`/`bvalue`/`creepage`/`anchor-length`/`steady-arm`/`cross-span`/`pole-capacity`/`cantilever`）为站点**内联引擎计算器**（引擎直嵌页面 HTML，不经 calc-core），以其 online 页面公式为基准；
 - 站点侧公式变更时，本仓库同步更新并补充/修订对应测试；
 - 本仓库的公式变更同样会回流站点，两边的计算结果保持一致；
 - `meta.ts` 中的参考依据（标准号 + 年份）随两侧更新同步修订。
 
-当前同步状态：`calc-core.js` 与 `src/` 一致（2026-09-05 校验，152 项测试全绿）。
+当前同步状态：20 个模块与站点一致（2026-09-14 校验，212 项测试全绿）。
 
 ## ⚠️ 免责声明
 

package/dist/{chunk-VXVTT6WS.js → chunk-2YFKWFBJ.js}

@@ -24,6 +24,7 @@ var TEST_MOMENT_FACTOR = 1.5;
 function poleCapacityCheck(input) {
   const { section, contactWireTensionKN, messengerTensionKN, staggerMM, spanM, resultantHeightM, windPressurePa, poleWidthM, poleHeightM, wireWindLoadN } = input;
   if (!(contactWireTensionKN >= 0) || !(messengerTensionKN >= 0)) throw new RangeError("\u5F20\u529B\u4E0D\u80FD\u4E3A\u8D1F");
+  if (!(spanM > 0)) throw new RangeError("\u8DE8\u8DDD\u5FC5\u987B\u4E3A\u6B63\uFF0C\u6536\u5230 " + spanM + " m");
   const T = contactWireTensionKN + messengerTensionKN;
   const a = staggerMM / 1e3;
   const Fz = 4 * T * a / spanM;
@@ -55,4 +56,4 @@ export {
   TEST_MOMENT_FACTOR,
   poleCapacityCheck
 };
-//# sourceMappingURL=chunk-VXVTT6WS.js.map
+//# sourceMappingURL=chunk-2YFKWFBJ.js.map

package/dist/{chunk-VXVTT6WS.js.map → chunk-2YFKWFBJ.js.map}

@@ -1 +1 @@
-{"version":3,"sources":["../src/pole-capacity/meta.ts","../src/pole-capacity/index.ts"],"sourcesContent":["import type { CalculatorMeta } from '../types';\n\nexport const poleCapacityMeta: CalculatorMeta = {\n  name: '支柱容量选型校核',\n  nameEn: 'Mast Capacity Selection Check',\n  summary: '容量比较法：悬挂水平力与支柱风载合成工作弯矩，对照 GB/T 25020.1 钢支柱检验弯矩系列选型。',\n  formula: [\n    '直线之字力 F_z = 4(T_j+T_c)·a/l；曲线力 F_q = (T_j+T_c)·l/R',\n    '工作弯矩 M = F_h·h_e + P·b·h²/2 + F_wl·h_e',\n    '承载力检验弯矩 = 1.5 × 标称容量（25020.1 表 A.2 表值规律）',\n  ],\n  references: [\n    '钢柱直接依据：GB/T 25020.1-2025 第 5.1.1 条 + 附录 A 检验弯矩系列',\n    '同口径混凝土柱条款：TB/T 2286-2020 第 5.9.2 条（荷载矢量组合不大于检验弯矩）',\n    '分项系数极限状态法（GB/T 32578-2016 6.3.3 表 15）为设计正式口径，不可混用',\n  ],\n  scope: ['张力：5~45 kN', '跨距：30~90 m', '风压：100~1500 Pa', '支柱高：5~20 m'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/pole-capacity/',\n};\n","export { poleCapacityMeta } from './meta';\n\n/** GB/T 25020.1-2025 格构式钢支柱标称容量系列（表 A.2），kN·m */\nexport const STEEL_POLE_SERIES_KNM = [150, 200, 250, 300, 350, 400, 450, 500, 550, 600, 650, 750, 900, 1050, 1200, 1500] as const;\n\n/** 承载力检验弯矩 = 1.5 × 标称容量（25020.1 表 A.2 表值规律） */\nexport const TEST_MOMENT_FACTOR = 1.5;\n\n/** 支柱容量校核输入。单位：kN、m、mm、Pa。 */\nexport interface PoleCapacityInput {\n  /** 区段类型 */\n  readonly section: 'line' | 'curve';\n  /** 接触线张力 T_j，kN */\n  readonly contactWireTensionKN: number;\n  /** 承力索张力 T_c，kN */\n  readonly messengerTensionKN: number;\n  /** 拉出值 a，mm */\n  readonly staggerMM: number;\n  /** 跨距 l，m */\n  readonly spanM: number;\n  /** 曲线半径 R，m（曲线区段） */\n  readonly curveRadiusM?: number;\n  /** 水平力合力作用高度 h_e，m */\n  readonly resultantHeightM: number;\n  /** 设计最大风压 P，Pa */\n  readonly windPressurePa: number;\n  /** 支柱迎风宽度 b，m */\n  readonly poleWidthM: number;\n  /** 支柱高度 h，m */\n  readonly poleHeightM: number;\n  /** 线索风载 F_wl，N */\n  readonly wireWindLoadN?: number;\n}\n\nexport interface PoleCapacityResult {\n  /** 悬挂水平力 F_h，N */\n  readonly horizontalForceN: number;\n  /** 工作弯矩 M，kN·m */\n  readonly workMomentKNM: number;\n  /** 折合标称容量（÷1.5），kN·m */\n  readonly nominalNeedKNM: number;\n  /** 选型结果 */\n  readonly selection: string | null;\n}\n\n/** 支柱容量选型（容量比较法，TB/T 2286 5.9.2 检验弯矩口径；钢柱 25020.1 5.1.1+附录A） */\nexport function poleCapacityCheck(input: PoleCapacityInput): PoleCapacityResult {\n  const { section, contactWireTensionKN, messengerTensionKN, staggerMM, spanM, resultantHeightM, windPressurePa, poleWidthM, poleHeightM, wireWindLoadN } = input;\n  if (!(contactWireTensionKN >= 0) || !(messengerTensionKN >= 0)) throw new RangeError('张力不能为负');\n  const T = contactWireTensionKN + messengerTensionKN;\n  const a = staggerMM / 1e3;\n  const Fz = (4 * T * a) / spanM; // kN\n  let Fh: number;\n  if (section === 'curve') {\n    if (!(input.curveRadiusM && input.curveRadiusM > 0)) throw new RangeError('曲线半径必须为正');\n    const Fq = (T * spanM) / input.curveRadiusM;\n    Fh = Math.abs(Fq - Fz);\n  } else {\n    Fh = Fz;\n  }\n  const M1 = Fh * resultantHeightM; // 悬挂水平力矩 kN·m\n  const M2 = (windPressurePa * poleWidthM * Math.pow(poleHeightM, 2) / 2) / 1e3; // 支柱风载矩\n  const M3 = ((wireWindLoadN ?? 0) * resultantHeightM) / 1e3;\n  const M = M1 + M2 + M3;\n  const nomNeed = M / TEST_MOMENT_FACTOR;\n  const pick = STEEL_POLE_SERIES_KNM.find((n) => n >= nomNeed) ?? null;\n  return {\n    horizontalForceN: Fh * 1e3,\n    workMomentKNM: M,\n    nominalNeedKNM: nomNeed,\n    selection: pick ? 'G' + pick : null,\n  };\n}\n"],"mappings":";AAEO,IAAM,mBAAmC;AAAA,EAC9C,MAAM;AAAA,EACN,QAAQ;AAAA,EACR,SAAS;AAAA,EACT,SAAS;AAAA,IACP;AAAA,IACA;AAAA,IACA;AAAA,EACF;AAAA,EACA,YAAY;AAAA,IACV;AAAA,IACA;AAAA,IACA;AAAA,EACF;AAAA,EACA,OAAO,CAAC,6BAAc,6BAAc,iCAAkB,gCAAY;AAAA,EAClE,YAAY;AAAA,EACZ,QAAQ;AACV;;;AChBO,IAAM,wBAAwB,CAAC,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,MAAM,MAAM,IAAI;AAGhH,IAAM,qBAAqB;AAwC3B,SAAS,kBAAkB,OAA8C;AAC9E,QAAM,EAAE,SAAS,sBAAsB,oBAAoB,WAAW,OAAO,kBAAkB,gBAAgB,YAAY,aAAa,cAAc,IAAI;AAC1J,MAAI,EAAE,wBAAwB,MAAM,EAAE,sBAAsB,GAAI,OAAM,IAAI,WAAW,sCAAQ;AAC7F,QAAM,IAAI,uBAAuB;AACjC,QAAM,IAAI,YAAY;AACtB,QAAM,KAAM,IAAI,IAAI,IAAK;AACzB,MAAI;AACJ,MAAI,YAAY,SAAS;AACvB,QAAI,EAAE,MAAM,gBAAgB,MAAM,eAAe,GAAI,OAAM,IAAI,WAAW,kDAAU;AACpF,UAAM,KAAM,IAAI,QAAS,MAAM;AAC/B,SAAK,KAAK,IAAI,KAAK,EAAE;AAAA,EACvB,OAAO;AACL,SAAK;AAAA,EACP;AACA,QAAM,KAAK,KAAK;AAChB,QAAM,KAAM,iBAAiB,aAAa,KAAK,IAAI,aAAa,CAAC,IAAI,IAAK;AAC1E,QAAM,MAAO,iBAAiB,KAAK,mBAAoB;AACvD,QAAM,IAAI,KAAK,KAAK;AACpB,QAAM,UAAU,IAAI;AACpB,QAAM,OAAO,sBAAsB,KAAK,CAAC,MAAM,KAAK,OAAO,KAAK;AAChE,SAAO;AAAA,IACL,kBAAkB,KAAK;AAAA,IACvB,eAAe;AAAA,IACf,gBAAgB;AAAA,IAChB,WAAW,OAAO,MAAM,OAAO;AAAA,EACjC;AACF;","names":[]}
+{"version":3,"sources":["../src/pole-capacity/meta.ts","../src/pole-capacity/index.ts"],"sourcesContent":["import type { CalculatorMeta } from '../types';\n\nexport const poleCapacityMeta: CalculatorMeta = {\n  name: '支柱容量选型校核',\n  nameEn: 'Mast Capacity Selection Check',\n  summary: '容量比较法：悬挂水平力与支柱风载合成工作弯矩，对照 GB/T 25020.1 钢支柱检验弯矩系列选型。',\n  formula: [\n    '直线之字力 F_z = 4(T_j+T_c)·a/l；曲线力 F_q = (T_j+T_c)·l/R',\n    '工作弯矩 M = F_h·h_e + P·b·h²/2 + F_wl·h_e',\n    '承载力检验弯矩 = 1.5 × 标称容量（25020.1 表 A.2 表值规律）',\n  ],\n  references: [\n    '钢柱直接依据：GB/T 25020.1-2025 第 5.1.1 条 + 附录 A 检验弯矩系列',\n    '同口径混凝土柱条款：TB/T 2286-2020 第 5.9.2 条（荷载矢量组合不大于检验弯矩）',\n    '分项系数极限状态法（GB/T 32578-2016 6.3.3 表 15）为设计正式口径，不可混用',\n  ],\n  scope: ['张力：5~45 kN', '跨距：30~90 m', '风压：100~1500 Pa', '支柱高：5~20 m'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/pole-capacity/',\n};\n","export { poleCapacityMeta } from './meta';\n\n/** GB/T 25020.1-2025 格构式钢支柱标称容量系列（表 A.2），kN·m */\nexport const STEEL_POLE_SERIES_KNM = [150, 200, 250, 300, 350, 400, 450, 500, 550, 600, 650, 750, 900, 1050, 1200, 1500] as const;\n\n/** 承载力检验弯矩 = 1.5 × 标称容量（25020.1 表 A.2 表值规律） */\nexport const TEST_MOMENT_FACTOR = 1.5;\n\n/** 支柱容量校核输入。单位：kN、m、mm、Pa。 */\nexport interface PoleCapacityInput {\n  /** 区段类型 */\n  readonly section: 'line' | 'curve';\n  /** 接触线张力 T_j，kN */\n  readonly contactWireTensionKN: number;\n  /** 承力索张力 T_c，kN */\n  readonly messengerTensionKN: number;\n  /** 拉出值 a，mm */\n  readonly staggerMM: number;\n  /** 跨距 l，m */\n  readonly spanM: number;\n  /** 曲线半径 R，m（曲线区段） */\n  readonly curveRadiusM?: number;\n  /** 水平力合力作用高度 h_e，m */\n  readonly resultantHeightM: number;\n  /** 设计最大风压 P，Pa */\n  readonly windPressurePa: number;\n  /** 支柱迎风宽度 b，m */\n  readonly poleWidthM: number;\n  /** 支柱高度 h，m */\n  readonly poleHeightM: number;\n  /** 线索风载 F_wl，N */\n  readonly wireWindLoadN?: number;\n}\n\nexport interface PoleCapacityResult {\n  /** 悬挂水平力 F_h，N */\n  readonly horizontalForceN: number;\n  /** 工作弯矩 M，kN·m */\n  readonly workMomentKNM: number;\n  /** 折合标称容量（÷1.5），kN·m */\n  readonly nominalNeedKNM: number;\n  /** 选型结果 */\n  readonly selection: string | null;\n}\n\n/** 支柱容量选型（容量比较法，TB/T 2286 5.9.2 检验弯矩口径；钢柱 25020.1 5.1.1+附录A） */\nexport function poleCapacityCheck(input: PoleCapacityInput): PoleCapacityResult {\n  const { section, contactWireTensionKN, messengerTensionKN, staggerMM, spanM, resultantHeightM, windPressurePa, poleWidthM, poleHeightM, wireWindLoadN } = input;\n  if (!(contactWireTensionKN >= 0) || !(messengerTensionKN >= 0)) throw new RangeError('张力不能为负');\n  if (!(spanM > 0)) throw new RangeError('跨距必须为正，收到 ' + spanM + ' m');\n  const T = contactWireTensionKN + messengerTensionKN;\n  const a = staggerMM / 1e3;\n  const Fz = (4 * T * a) / spanM; // kN\n  let Fh: number;\n  if (section === 'curve') {\n    if (!(input.curveRadiusM && input.curveRadiusM > 0)) throw new RangeError('曲线半径必须为正');\n    const Fq = (T * spanM) / input.curveRadiusM;\n    Fh = Math.abs(Fq - Fz);\n  } else {\n    Fh = Fz;\n  }\n  const M1 = Fh * resultantHeightM; // 悬挂水平力矩 kN·m\n  const M2 = (windPressurePa * poleWidthM * Math.pow(poleHeightM, 2) / 2) / 1e3; // 支柱风载矩\n  const M3 = ((wireWindLoadN ?? 0) * resultantHeightM) / 1e3;\n  const M = M1 + M2 + M3;\n  const nomNeed = M / TEST_MOMENT_FACTOR;\n  const pick = STEEL_POLE_SERIES_KNM.find((n) => n >= nomNeed) ?? null;\n  return {\n    horizontalForceN: Fh * 1e3,\n    workMomentKNM: M,\n    nominalNeedKNM: nomNeed,\n    selection: pick ? 'G' + pick : null,\n  };\n}\n"],"mappings":";AAEO,IAAM,mBAAmC;AAAA,EAC9C,MAAM;AAAA,EACN,QAAQ;AAAA,EACR,SAAS;AAAA,EACT,SAAS;AAAA,IACP;AAAA,IACA;AAAA,IACA;AAAA,EACF;AAAA,EACA,YAAY;AAAA,IACV;AAAA,IACA;AAAA,IACA;AAAA,EACF;AAAA,EACA,OAAO,CAAC,6BAAc,6BAAc,iCAAkB,gCAAY;AAAA,EAClE,YAAY;AAAA,EACZ,QAAQ;AACV;;;AChBO,IAAM,wBAAwB,CAAC,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,KAAK,MAAM,MAAM,IAAI;AAGhH,IAAM,qBAAqB;AAwC3B,SAAS,kBAAkB,OAA8C;AAC9E,QAAM,EAAE,SAAS,sBAAsB,oBAAoB,WAAW,OAAO,kBAAkB,gBAAgB,YAAY,aAAa,cAAc,IAAI;AAC1J,MAAI,EAAE,wBAAwB,MAAM,EAAE,sBAAsB,GAAI,OAAM,IAAI,WAAW,sCAAQ;AAC7F,MAAI,EAAE,QAAQ,GAAI,OAAM,IAAI,WAAW,4DAAe,QAAQ,IAAI;AAClE,QAAM,IAAI,uBAAuB;AACjC,QAAM,IAAI,YAAY;AACtB,QAAM,KAAM,IAAI,IAAI,IAAK;AACzB,MAAI;AACJ,MAAI,YAAY,SAAS;AACvB,QAAI,EAAE,MAAM,gBAAgB,MAAM,eAAe,GAAI,OAAM,IAAI,WAAW,kDAAU;AACpF,UAAM,KAAM,IAAI,QAAS,MAAM;AAC/B,SAAK,KAAK,IAAI,KAAK,EAAE;AAAA,EACvB,OAAO;AACL,SAAK;AAAA,EACP;AACA,QAAM,KAAK,KAAK;AAChB,QAAM,KAAM,iBAAiB,aAAa,KAAK,IAAI,aAAa,CAAC,IAAI,IAAK;AAC1E,QAAM,MAAO,iBAAiB,KAAK,mBAAoB;AACvD,QAAM,IAAI,KAAK,KAAK;AACpB,QAAM,UAAU,IAAI;AACpB,QAAM,OAAO,sBAAsB,KAAK,CAAC,MAAM,KAAK,OAAO,KAAK;AAChE,SAAO;AAAA,IACL,kBAAkB,KAAK;AAAA,IACvB,eAAe;AAAA,IACf,gBAAgB;AAAA,IAChB,WAAW,OAAO,MAAM,OAAO;AAAA,EACjC;AACF;","names":[]}

package/dist/{chunk-CLVLOLUJ.js → chunk-3LUPNS4U.js}

@@ -30,7 +30,7 @@ function creepageCheck(input) {
   const kv = input.maxVoltageKV ?? 29;
   const uscdBands = USCD_BANDS.map((b) => ({
     label: b.label,
-    mm: b.max === Infinity ? Math.round(b.min * kv) : Math.round(b.min * kv)
+    mm: Math.round(b.min * kv)
   }));
   return { floorMM, passes: input.creepageMM >= floorMM, uscdBands };
 }
@@ -42,4 +42,4 @@ export {
   USCD_BANDS,
   creepageCheck
 };
-//# sourceMappingURL=chunk-CLVLOLUJ.js.map
+//# sourceMappingURL=chunk-3LUPNS4U.js.map

package/dist/{chunk-CLVLOLUJ.js.map → chunk-3LUPNS4U.js.map}

@@ -1 +1 @@
-{"version":3,"sources":["../src/creepage/meta.ts","../src/creepage/index.ts"],"sourcesContent":["import type { CalculatorMeta } from '../types';\n\nexport const creepageMeta: CalculatorMeta = {\n  name: '绝缘子爬电距离选型校核',\n  nameEn: 'Insulator Creepage Distance Check',\n  summary: '按 TB 10009-2016 第 5.3.2 条底线判定接触网绝缘最小爬电距离，附 GB/T 32586 比距三档对照。',\n  formula: [\n    '底线：一般区段 ≥1400 mm；V 形天窗上、下行正线间分段串 ≥1600 mm',\n    'GB/T 32586 统一爬电比距三档：正常 24~33、非正常 36~40、苛刻 >48 mm/kV',\n  ],\n  references: [\n    'TB 10009-2016 第 5.3.2 条第 1 款（绝对底线）',\n    'GB/T 32586-2016 第 4.4 条（统一爬电比距三档，按系统最高持续电压折算）',\n    '铁路体系以绝对值门槛判定，比距法仅作对照',\n  ],\n  scope: ['爬电距离：600~2500 mm', '系统最高电压：27.5~31 kV'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/creepage/',\n};\n","export { creepageMeta } from './meta';\n\n/** 接触网绝缘爬电距离底线（TB 10009-2016 第 5.3.2 条第 1 款），mm */\nexport const CREEPAGE_FLOOR_GENERAL = 1400;\n/** V 形天窗区段上、下行正线间分段绝缘子串底线，mm */\nexport const CREEPAGE_FLOOR_VCUT = 1600;\n\n/** GB/T 32586 统一爬电比距三档（第 4.4 条，按系统最高持续电压折算） */\nexport const USCD_BANDS = [\n  { label: '正常', min: 24, max: 33 },\n  { label: '非正常', min: 36, max: 40 },\n  { label: '苛刻', min: 48, max: Infinity },\n] as const;\n\n/** 爬电距离校核 */\nexport function creepageCheck(input: {\n  /** 绝缘子实际爬电距离，mm */\n  readonly creepageMM: number;\n  /** 使用场景：'general' 一般 | 'vcut' V 形天窗分段串 */\n  readonly scenario?: 'general' | 'vcut';\n  /** 系统最高电压，kV（GB/T 32586 折算用，默认 29） */\n  readonly maxVoltageKV?: number;\n}): {\n  floorMM: number; passes: boolean; uscdBands: { label: string; mm: number }[];\n} {\n  const floorMM = (input.scenario === 'vcut' ? CREEPAGE_FLOOR_VCUT : CREEPAGE_FLOOR_GENERAL);\n  const kv = input.maxVoltageKV ?? 29;\n  const uscdBands = USCD_BANDS.map((b) => ({\n    label: b.label,\n    mm: b.max === Infinity ? Math.round(b.min * kv) : Math.round(b.min * kv),\n  }));\n  return { floorMM, passes: input.creepageMM >= floorMM, uscdBands };\n}\n"],"mappings":";AAEO,IAAM,eAA+B;AAAA,EAC1C,MAAM;AAAA,EACN,QAAQ;AAAA,EACR,SAAS;AAAA,EACT,SAAS;AAAA,IACP;AAAA,IACA;AAAA,EACF;AAAA,EACA,YAAY;AAAA,IACV;AAAA,IACA;AAAA,IACA;AAAA,EACF;AAAA,EACA,OAAO,CAAC,6CAAoB,sDAAmB;AAAA,EAC/C,YAAY;AAAA,EACZ,QAAQ;AACV;;;ACfO,IAAM,yBAAyB;AAE/B,IAAM,sBAAsB;AAG5B,IAAM,aAAa;AAAA,EACxB,EAAE,OAAO,gBAAM,KAAK,IAAI,KAAK,GAAG;AAAA,EAChC,EAAE,OAAO,sBAAO,KAAK,IAAI,KAAK,GAAG;AAAA,EACjC,EAAE,OAAO,gBAAM,KAAK,IAAI,KAAK,SAAS;AACxC;AAGO,SAAS,cAAc,OAS5B;AACA,QAAM,UAAW,MAAM,aAAa,SAAS,sBAAsB;AACnE,QAAM,KAAK,MAAM,gBAAgB;AACjC,QAAM,YAAY,WAAW,IAAI,CAAC,OAAO;AAAA,IACvC,OAAO,EAAE;AAAA,IACT,IAAI,EAAE,QAAQ,WAAW,KAAK,MAAM,EAAE,MAAM,EAAE,IAAI,KAAK,MAAM,EAAE,MAAM,EAAE;AAAA,EACzE,EAAE;AACF,SAAO,EAAE,SAAS,QAAQ,MAAM,cAAc,SAAS,UAAU;AACnE;","names":[]}
+{"version":3,"sources":["../src/creepage/meta.ts","../src/creepage/index.ts"],"sourcesContent":["import type { CalculatorMeta } from '../types';\n\nexport const creepageMeta: CalculatorMeta = {\n  name: '绝缘子爬电距离选型校核',\n  nameEn: 'Insulator Creepage Distance Check',\n  summary: '按 TB 10009-2016 第 5.3.2 条底线判定接触网绝缘最小爬电距离，附 GB/T 32586 比距三档对照。',\n  formula: [\n    '底线：一般区段 ≥1400 mm；V 形天窗上、下行正线间分段串 ≥1600 mm',\n    'GB/T 32586 统一爬电比距三档：正常 24~33、非正常 36~40、苛刻 >48 mm/kV',\n  ],\n  references: [\n    'TB 10009-2016 第 5.3.2 条第 1 款（绝对底线）',\n    'GB/T 32586-2016 第 4.4 条（统一爬电比距三档，按系统最高持续电压折算）',\n    '铁路体系以绝对值门槛判定，比距法仅作对照',\n  ],\n  scope: ['爬电距离：600~2500 mm', '系统最高电压：27.5~31 kV'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/creepage/',\n};\n","export { creepageMeta } from './meta';\n\n/** 接触网绝缘爬电距离底线（TB 10009-2016 第 5.3.2 条第 1 款），mm */\nexport const CREEPAGE_FLOOR_GENERAL = 1400;\n/** V 形天窗区段上、下行正线间分段绝缘子串底线，mm */\nexport const CREEPAGE_FLOOR_VCUT = 1600;\n\n/** GB/T 32586 统一爬电比距三档（第 4.4 条，按系统最高持续电压折算） */\nexport const USCD_BANDS = [\n  { label: '正常', min: 24, max: 33 },\n  { label: '非正常', min: 36, max: 40 },\n  { label: '苛刻', min: 48, max: Infinity },\n] as const;\n\n/** 爬电距离校核 */\nexport function creepageCheck(input: {\n  /** 绝缘子实际爬电距离，mm */\n  readonly creepageMM: number;\n  /** 使用场景：'general' 一般 | 'vcut' V 形天窗分段串 */\n  readonly scenario?: 'general' | 'vcut';\n  /** 系统最高电压，kV（GB/T 32586 折算用，默认 29） */\n  readonly maxVoltageKV?: number;\n}): {\n  floorMM: number; passes: boolean; uscdBands: { label: string; mm: number }[];\n} {\n  const floorMM = (input.scenario === 'vcut' ? CREEPAGE_FLOOR_VCUT : CREEPAGE_FLOOR_GENERAL);\n  const kv = input.maxVoltageKV ?? 29;\n  const uscdBands = USCD_BANDS.map((b) => ({\n    label: b.label,\n    mm: Math.round(b.min * kv),\n  }));\n  return { floorMM, passes: input.creepageMM >= floorMM, uscdBands };\n}\n"],"mappings":";AAEO,IAAM,eAA+B;AAAA,EAC1C,MAAM;AAAA,EACN,QAAQ;AAAA,EACR,SAAS;AAAA,EACT,SAAS;AAAA,IACP;AAAA,IACA;AAAA,EACF;AAAA,EACA,YAAY;AAAA,IACV;AAAA,IACA;AAAA,IACA;AAAA,EACF;AAAA,EACA,OAAO,CAAC,6CAAoB,sDAAmB;AAAA,EAC/C,YAAY;AAAA,EACZ,QAAQ;AACV;;;ACfO,IAAM,yBAAyB;AAE/B,IAAM,sBAAsB;AAG5B,IAAM,aAAa;AAAA,EACxB,EAAE,OAAO,gBAAM,KAAK,IAAI,KAAK,GAAG;AAAA,EAChC,EAAE,OAAO,sBAAO,KAAK,IAAI,KAAK,GAAG;AAAA,EACjC,EAAE,OAAO,gBAAM,KAAK,IAAI,KAAK,SAAS;AACxC;AAGO,SAAS,cAAc,OAS5B;AACA,QAAM,UAAW,MAAM,aAAa,SAAS,sBAAsB;AACnE,QAAM,KAAK,MAAM,gBAAgB;AACjC,QAAM,YAAY,WAAW,IAAI,CAAC,OAAO;AAAA,IACvC,OAAO,EAAE;AAAA,IACT,IAAI,KAAK,MAAM,EAAE,MAAM,EAAE;AAAA,EAC3B,EAAE;AACF,SAAO,EAAE,SAAS,QAAQ,MAAM,cAAc,SAAS,UAAU;AACnE;","names":[]}

package/dist/{chunk-LBGUOTCJ.cjs → chunk-AVQ4F6DF.cjs}

@@ -30,7 +30,7 @@ function creepageCheck(input) {
   const kv = _nullishCoalesce(input.maxVoltageKV, () => ( 29));
   const uscdBands = USCD_BANDS.map((b) => ({
     label: b.label,
-    mm: b.max === Infinity ? Math.round(b.min * kv) : Math.round(b.min * kv)
+    mm: Math.round(b.min * kv)
   }));
   return { floorMM, passes: input.creepageMM >= floorMM, uscdBands };
 }
@@ -42,4 +42,4 @@ function creepageCheck(input) {
 
 
 exports.creepageMeta = creepageMeta; exports.CREEPAGE_FLOOR_GENERAL = CREEPAGE_FLOOR_GENERAL; exports.CREEPAGE_FLOOR_VCUT = CREEPAGE_FLOOR_VCUT; exports.USCD_BANDS = USCD_BANDS; exports.creepageCheck = creepageCheck;
-//# sourceMappingURL=chunk-LBGUOTCJ.cjs.map
+//# sourceMappingURL=chunk-AVQ4F6DF.cjs.map

package/dist/chunk-AVQ4F6DF.cjs.map

@@ -0,0 +1 @@
+{"version":3,"sources":["/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-AVQ4F6DF.cjs","../src/creepage/meta.ts","../src/creepage/index.ts"],"names":[],"mappings":"AAAA;ACEO,IAAM,aAAA,EAA+B;AAAA,EAC1C,IAAA,EAAM,oEAAA;AAAA,EACN,MAAA,EAAQ,mCAAA;AAAA,EACR,OAAA,EAAS,sMAAA;AAAA,EACT,OAAA,EAAS;AAAA,IACP,8JAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,UAAA,EAAY;AAAA,IACV,sFAAA;AAAA,IACA,uKAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,KAAA,EAAO,CAAC,2CAAA,EAAoB,sDAAmB,CAAA;AAAA,EAC/C,UAAA,EAAY,sKAAA;AAAA,EACZ,MAAA,EAAQ;AACV,CAAA;ADAA;AACA;AEhBO,IAAM,uBAAA,EAAyB,IAAA;AAE/B,IAAM,oBAAA,EAAsB,IAAA;AAG5B,IAAM,WAAA,EAAa;AAAA,EACxB,EAAE,KAAA,EAAO,cAAA,EAAM,GAAA,EAAK,EAAA,EAAI,GAAA,EAAK,GAAG,CAAA;AAAA,EAChC,EAAE,KAAA,EAAO,oBAAA,EAAO,GAAA,EAAK,EAAA,EAAI,GAAA,EAAK,GAAG,CAAA;AAAA,EACjC,EAAE,KAAA,EAAO,cAAA,EAAM,GAAA,EAAK,EAAA,EAAI,GAAA,EAAK,SAAS;AACxC,CAAA;AAGO,SAAS,aAAA,CAAc,KAAA,EAS5B;AACA,EAAA,MAAM,QAAA,EAAW,KAAA,CAAM,SAAA,IAAa,OAAA,EAAS,oBAAA,EAAsB,sBAAA;AACnE,EAAA,MAAM,GAAA,mBAAK,KAAA,CAAM,YAAA,UAAgB,IAAA;AACjC,EAAA,MAAM,UAAA,EAAY,UAAA,CAAW,GAAA,CAAI,CAAC,CAAA,EAAA,GAAA,CAAO;AAAA,IACvC,KAAA,EAAO,CAAA,CAAE,KAAA;AAAA,IACT,EAAA,EAAI,IAAA,CAAK,KAAA,CAAM,CAAA,CAAE,IAAA,EAAM,EAAE;AAAA,EAC3B,CAAA,CAAE,CAAA;AACF,EAAA,OAAO,EAAE,OAAA,EAAS,MAAA,EAAQ,KAAA,CAAM,WAAA,GAAc,OAAA,EAAS,UAAU,CAAA;AACnE;AFIA;AACA;AACE;AACA;AACA;AACA;AACA;AACF,wNAAC","file":"/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-AVQ4F6DF.cjs","sourcesContent":[null,"import type { CalculatorMeta } from '../types';\n\nexport const creepageMeta: CalculatorMeta = {\n  name: '绝缘子爬电距离选型校核',\n  nameEn: 'Insulator Creepage Distance Check',\n  summary: '按 TB 10009-2016 第 5.3.2 条底线判定接触网绝缘最小爬电距离，附 GB/T 32586 比距三档对照。',\n  formula: [\n    '底线：一般区段 ≥1400 mm；V 形天窗上、下行正线间分段串 ≥1600 mm',\n    'GB/T 32586 统一爬电比距三档：正常 24~33、非正常 36~40、苛刻 >48 mm/kV',\n  ],\n  references: [\n    'TB 10009-2016 第 5.3.2 条第 1 款（绝对底线）',\n    'GB/T 32586-2016 第 4.4 条（统一爬电比距三档，按系统最高持续电压折算）',\n    '铁路体系以绝对值门槛判定，比距法仅作对照',\n  ],\n  scope: ['爬电距离：600~2500 mm', '系统最高电压：27.5~31 kV'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/creepage/',\n};\n","export { creepageMeta } from './meta';\n\n/** 接触网绝缘爬电距离底线（TB 10009-2016 第 5.3.2 条第 1 款），mm */\nexport const CREEPAGE_FLOOR_GENERAL = 1400;\n/** V 形天窗区段上、下行正线间分段绝缘子串底线，mm */\nexport const CREEPAGE_FLOOR_VCUT = 1600;\n\n/** GB/T 32586 统一爬电比距三档（第 4.4 条，按系统最高持续电压折算） */\nexport const USCD_BANDS = [\n  { label: '正常', min: 24, max: 33 },\n  { label: '非正常', min: 36, max: 40 },\n  { label: '苛刻', min: 48, max: Infinity },\n] as const;\n\n/** 爬电距离校核 */\nexport function creepageCheck(input: {\n  /** 绝缘子实际爬电距离，mm */\n  readonly creepageMM: number;\n  /** 使用场景：'general' 一般 | 'vcut' V 形天窗分段串 */\n  readonly scenario?: 'general' | 'vcut';\n  /** 系统最高电压，kV（GB/T 32586 折算用，默认 29） */\n  readonly maxVoltageKV?: number;\n}): {\n  floorMM: number; passes: boolean; uscdBands: { label: string; mm: number }[];\n} {\n  const floorMM = (input.scenario === 'vcut' ? CREEPAGE_FLOOR_VCUT : CREEPAGE_FLOOR_GENERAL);\n  const kv = input.maxVoltageKV ?? 29;\n  const uscdBands = USCD_BANDS.map((b) => ({\n    label: b.label,\n    mm: Math.round(b.min * kv),\n  }));\n  return { floorMM, passes: input.creepageMM >= floorMM, uscdBands };\n}\n"]}

package/dist/{chunk-PYNVEHGR.cjs → chunk-CF663UNG.cjs}

@@ -32,6 +32,8 @@ function tensionFromSagKN(weightNPerM, spanM, sagMM2) {
   return weightNPerM * spanM * spanM / (8 * sagM) / 1e3;
 }
 function maxSpanFromSagM(weightNPerM, tensionKN, sagLimitMM) {
+  if (!(tensionKN > 0)) throw new RangeError("\u5F20\u529B\u5FC5\u987B\u4E3A\u6B63\uFF0C\u6536\u5230 " + tensionKN + " kN");
+  if (!(weightNPerM > 0)) throw new RangeError("\u5355\u4F4D\u91CD\u5FC5\u987B\u4E3A\u6B63\uFF0C\u6536\u5230 " + weightNPerM + " N/m");
   if (!(sagLimitMM > 0)) throw new RangeError("\u9650\u503C\u5F1B\u5EA6\u5FC5\u987B\u4E3A\u6B63\uFF0C\u6536\u5230 " + sagLimitMM + " mm");
   const sagM = sagLimitMM / 1e3;
   return Math.sqrt(8 * tensionKN * 1e3 * sagM / weightNPerM);
@@ -43,4 +45,4 @@ function maxSpanFromSagM(weightNPerM, tensionKN, sagLimitMM) {
 
 
 exports.sagMeta = sagMeta; exports.sagMM = sagMM; exports.tensionFromSagKN = tensionFromSagKN; exports.maxSpanFromSagM = maxSpanFromSagM;
-//# sourceMappingURL=chunk-PYNVEHGR.cjs.map
+//# sourceMappingURL=chunk-CF663UNG.cjs.map

package/dist/chunk-CF663UNG.cjs.map

@@ -0,0 +1 @@
+{"version":3,"sources":["/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-CF663UNG.cjs","../src/sag/meta.ts","../src/sag/index.ts"],"names":["sagMM"],"mappings":"AAAA;ACEO,IAAM,QAAA,EAA0B;AAAA,EACrC,IAAA,EAAM,2EAAA;AAAA,EACN,MAAA,EAAQ,uBAAA;AAAA,EACR,OAAA,EAAS,sLAAA;AAAA,EACT,OAAA,EAAS;AAAA,IACP,kCAAA;AAAA,IACA,kDAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,UAAA,EAAY;AAAA,IACV,oQAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,KAAA,EAAO,CAAC,6BAAA,EAAgB,4BAAA,EAAe,oCAAgB,CAAA;AAAA,EACvD,UAAA,EAAY,sKAAA;AAAA,EACZ,MAAA,EAAQ;AACV,CAAA;ADAA;AACA;AENO,SAAS,KAAA,CAAM,KAAA,EAAyB;AAC7C,EAAA,MAAM,EAAE,SAAA,EAAW,KAAA,EAAO,YAAY,EAAA,EAAI,KAAA;AAC1C,EAAA,GAAA,CAAI,CAAA,CAAE,UAAA,EAAY,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,0DAAA,EAAe,UAAA,EAAY,KAAK,CAAA;AAC3E,EAAA,GAAA,CAAI,CAAA,CAAE,MAAA,EAAQ,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,0DAAA,EAAe,MAAA,EAAQ,IAAI,CAAA;AAClE,EAAA,GAAA,CAAI,CAAA,CAAE,YAAA,GAAe,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,gEAAA,EAAgB,YAAA,EAAc,MAAM,CAAA;AAClF,EAAA,MAAM,KAAA,EAAQ,YAAA,EAAc,MAAA,EAAQ,MAAA,EAAA,CAAU,EAAA,EAAI,UAAA,EAAY,GAAA,CAAA;AAC9D,EAAA,OAAO,KAAA,EAAO,GAAA;AAChB;AAGO,SAAS,gBAAA,CAAiB,WAAA,EAAqB,KAAA,EAAeA,MAAAA,EAAuB;AAC1F,EAAA,GAAA,CAAI,CAAA,CAAEA,OAAAA,EAAQ,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,0DAAA,EAAeA,OAAAA,EAAQ,KAAK,CAAA;AACnE,EAAA,MAAM,KAAA,EAAOA,OAAAA,EAAQ,GAAA;AACrB,EAAA,OAAQ,YAAA,EAAc,MAAA,EAAQ,MAAA,EAAA,CAAU,EAAA,EAAI,IAAA,EAAA,EAAQ,GAAA;AACtD;AAGO,SAAS,eAAA,CAAgB,WAAA,EAAqB,SAAA,EAAmB,UAAA,EAA4B;AAClG,EAAA,GAAA,CAAI,CAAA,CAAE,UAAA,EAAY,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,0DAAA,EAAe,UAAA,EAAY,KAAK,CAAA;AAC3E,EAAA,GAAA,CAAI,CAAA,CAAE,YAAA,EAAc,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,gEAAA,EAAgB,YAAA,EAAc,MAAM,CAAA;AACjF,EAAA,GAAA,CAAI,CAAA,CAAE,WAAA,EAAa,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,sEAAA,EAAiB,WAAA,EAAa,KAAK,CAAA;AAC/E,EAAA,MAAM,KAAA,EAAO,WAAA,EAAa,GAAA;AAC1B,EAAA,OAAO,IAAA,CAAK,IAAA,CAAM,EAAA,EAAI,UAAA,EAAY,IAAA,EAAM,KAAA,EAAQ,WAAW,CAAA;AAC7D;AFIA;AACA;AACE;AACA;AACA;AACA;AACF,yIAAC","file":"/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-CF663UNG.cjs","sourcesContent":[null,"import type { CalculatorMeta } from '../types';\n\nexport const sagMeta: CalculatorMeta = {\n  name: '弛度速算（弛度-张力互算）',\n  nameEn: 'Sag Quick Calculation',\n  summary: '等高悬挂抛物线近似（小弛度假设）下弛度、张力与最大跨距互算。',\n  formula: [\n    '弛度 f = g·l²/(8T)',\n    '反算张力 T = g·l²/(8·f)',\n    '反算跨距上限 l_max = √(8·T·f_max/g)',\n  ],\n  references: [\n    '限值（TB 10009-2016 第 5.1.9 条，推荐性「不宜大于」口径）：链形悬挂接触线 150 mm、简单悬挂 250 mm、低速区段 350 mm',\n    '等高悬挂抛物线近似，适用于 f/l ≤ 1/10',\n  ],\n  scope: ['张力 T：1~40 kN', '跨距 l：5~80 m', '单位重 g：5~25 N/m'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/sag/',\n};\n","export { sagMeta } from './meta';\n\n/** 弛度计算参数。单位：张力 kN、跨距 m、单位重 N/m。 */\nexport interface SagInput {\n  /** 接触线/承力索张力 T，kN */\n  readonly tensionKN: number;\n  /** 跨距 l，m */\n  readonly spanM: number;\n  /** 单位长度重量 g，N/m */\n  readonly weightNPerM: number;\n}\n\n/** 弛度 f = g·l²/(8T)，mm */\nexport function sagMM(input: SagInput): number {\n  const { tensionKN, spanM, weightNPerM } = input;\n  if (!(tensionKN > 0)) throw new RangeError('张力必须为正，收到 ' + tensionKN + ' kN');\n  if (!(spanM > 0)) throw new RangeError('跨距必须为正，收到 ' + spanM + ' m');\n  if (!(weightNPerM >= 0)) throw new RangeError('单位重不能为负，收到 ' + weightNPerM + ' N/m');\n  const sagM = (weightNPerM * spanM * spanM) / (8 * tensionKN * 1e3);\n  return sagM * 1e3;\n}\n\n/** 反算张力：给定弛度求张力 T = g·l²/(8·f)，kN */\nexport function tensionFromSagKN(weightNPerM: number, spanM: number, sagMM: number): number {\n  if (!(sagMM > 0)) throw new RangeError('弛度必须为正，收到 ' + sagMM + ' mm');\n  const sagM = sagMM / 1e3;\n  return (weightNPerM * spanM * spanM) / (8 * sagM) / 1e3;\n}\n\n/** 反算最大跨距：给定张力与限值弛度 l_max = √(8·T·f_max/g)，m */\nexport function maxSpanFromSagM(weightNPerM: number, tensionKN: number, sagLimitMM: number): number {\n  if (!(tensionKN > 0)) throw new RangeError('张力必须为正，收到 ' + tensionKN + ' kN');\n  if (!(weightNPerM > 0)) throw new RangeError('单位重必须为正，收到 ' + weightNPerM + ' N/m');\n  if (!(sagLimitMM > 0)) throw new RangeError('限值弛度必须为正，收到 ' + sagLimitMM + ' mm');\n  const sagM = sagLimitMM / 1e3;\n  return Math.sqrt((8 * tensionKN * 1e3 * sagM) / weightNPerM);\n}\n"]}

package/dist/{chunk-C2XU3XKP.js → chunk-Q7UD52SC.js}

@@ -32,6 +32,8 @@ function tensionFromSagKN(weightNPerM, spanM, sagMM2) {
   return weightNPerM * spanM * spanM / (8 * sagM) / 1e3;
 }
 function maxSpanFromSagM(weightNPerM, tensionKN, sagLimitMM) {
+  if (!(tensionKN > 0)) throw new RangeError("\u5F20\u529B\u5FC5\u987B\u4E3A\u6B63\uFF0C\u6536\u5230 " + tensionKN + " kN");
+  if (!(weightNPerM > 0)) throw new RangeError("\u5355\u4F4D\u91CD\u5FC5\u987B\u4E3A\u6B63\uFF0C\u6536\u5230 " + weightNPerM + " N/m");
   if (!(sagLimitMM > 0)) throw new RangeError("\u9650\u503C\u5F1B\u5EA6\u5FC5\u987B\u4E3A\u6B63\uFF0C\u6536\u5230 " + sagLimitMM + " mm");
   const sagM = sagLimitMM / 1e3;
   return Math.sqrt(8 * tensionKN * 1e3 * sagM / weightNPerM);
@@ -43,4 +45,4 @@ export {
   tensionFromSagKN,
   maxSpanFromSagM
 };
-//# sourceMappingURL=chunk-C2XU3XKP.js.map
+//# sourceMappingURL=chunk-Q7UD52SC.js.map

package/dist/{chunk-C2XU3XKP.js.map → chunk-Q7UD52SC.js.map}

@@ -1 +1 @@
-{"version":3,"sources":["../src/sag/meta.ts","../src/sag/index.ts"],"sourcesContent":["import type { CalculatorMeta } from '../types';\n\nexport const sagMeta: CalculatorMeta = {\n  name: '弛度速算（弛度-张力互算）',\n  nameEn: 'Sag Quick Calculation',\n  summary: '等高悬挂抛物线近似（小弛度假设）下弛度、张力与最大跨距互算。',\n  formula: [\n    '弛度 f = g·l²/(8T)',\n    '反算张力 T = g·l²/(8·f)',\n    '反算跨距上限 l_max = √(8·T·f_max/g)',\n  ],\n  references: [\n    '限值（TB 10009-2016 第 5.1.9 条，推荐性「不宜大于」口径）：链形悬挂接触线 150 mm、简单悬挂 250 mm、低速区段 350 mm',\n    '等高悬挂抛物线近似，适用于 f/l ≤ 1/10',\n  ],\n  scope: ['张力 T：1~40 kN', '跨距 l：5~80 m', '单位重 g：5~25 N/m'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/sag/',\n};\n","export { sagMeta } from './meta';\n\n/** 弛度计算参数。单位：张力 kN、跨距 m、单位重 N/m。 */\nexport interface SagInput {\n  /** 接触线/承力索张力 T，kN */\n  readonly tensionKN: number;\n  /** 跨距 l，m */\n  readonly spanM: number;\n  /** 单位长度重量 g，N/m */\n  readonly weightNPerM: number;\n}\n\n/** 弛度 f = g·l²/(8T)，mm */\nexport function sagMM(input: SagInput): number {\n  const { tensionKN, spanM, weightNPerM } = input;\n  if (!(tensionKN > 0)) throw new RangeError('张力必须为正，收到 ' + tensionKN + ' kN');\n  if (!(spanM > 0)) throw new RangeError('跨距必须为正，收到 ' + spanM + ' m');\n  if (!(weightNPerM >= 0)) throw new RangeError('单位重不能为负，收到 ' + weightNPerM + ' N/m');\n  const sagM = (weightNPerM * spanM * spanM) / (8 * tensionKN * 1e3);\n  return sagM * 1e3;\n}\n\n/** 反算张力：给定弛度求张力 T = g·l²/(8·f)，kN */\nexport function tensionFromSagKN(weightNPerM: number, spanM: number, sagMM: number): number {\n  if (!(sagMM > 0)) throw new RangeError('弛度必须为正，收到 ' + sagMM + ' mm');\n  const sagM = sagMM / 1e3;\n  return (weightNPerM * spanM * spanM) / (8 * sagM) / 1e3;\n}\n\n/** 反算最大跨距：给定张力与限值弛度 l_max = √(8·T·f_max/g)，m */\nexport function maxSpanFromSagM(weightNPerM: number, tensionKN: number, sagLimitMM: number): number {\n  if (!(sagLimitMM > 0)) throw new RangeError('限值弛度必须为正，收到 ' + sagLimitMM + ' mm');\n  const sagM = sagLimitMM / 1e3;\n  return Math.sqrt((8 * tensionKN * 1e3 * sagM) / weightNPerM);\n}\n"],"mappings":";AAEO,IAAM,UAA0B;AAAA,EACrC,MAAM;AAAA,EACN,QAAQ;AAAA,EACR,SAAS;AAAA,EACT,SAAS;AAAA,IACP;AAAA,IACA;AAAA,IACA;AAAA,EACF;AAAA,EACA,YAAY;AAAA,IACV;AAAA,IACA;AAAA,EACF;AAAA,EACA,OAAO,CAAC,+BAAgB,8BAAe,oCAAgB;AAAA,EACvD,YAAY;AAAA,EACZ,QAAQ;AACV;;;ACLO,SAAS,MAAM,OAAyB;AAC7C,QAAM,EAAE,WAAW,OAAO,YAAY,IAAI;AAC1C,MAAI,EAAE,YAAY,GAAI,OAAM,IAAI,WAAW,4DAAe,YAAY,KAAK;AAC3E,MAAI,EAAE,QAAQ,GAAI,OAAM,IAAI,WAAW,4DAAe,QAAQ,IAAI;AAClE,MAAI,EAAE,eAAe,GAAI,OAAM,IAAI,WAAW,kEAAgB,cAAc,MAAM;AAClF,QAAM,OAAQ,cAAc,QAAQ,SAAU,IAAI,YAAY;AAC9D,SAAO,OAAO;AAChB;AAGO,SAAS,iBAAiB,aAAqB,OAAeA,QAAuB;AAC1F,MAAI,EAAEA,SAAQ,GAAI,OAAM,IAAI,WAAW,4DAAeA,SAAQ,KAAK;AACnE,QAAM,OAAOA,SAAQ;AACrB,SAAQ,cAAc,QAAQ,SAAU,IAAI,QAAQ;AACtD;AAGO,SAAS,gBAAgB,aAAqB,WAAmB,YAA4B;AAClG,MAAI,EAAE,aAAa,GAAI,OAAM,IAAI,WAAW,wEAAiB,aAAa,KAAK;AAC/E,QAAM,OAAO,aAAa;AAC1B,SAAO,KAAK,KAAM,IAAI,YAAY,MAAM,OAAQ,WAAW;AAC7D;","names":["sagMM"]}
+{"version":3,"sources":["../src/sag/meta.ts","../src/sag/index.ts"],"sourcesContent":["import type { CalculatorMeta } from '../types';\n\nexport const sagMeta: CalculatorMeta = {\n  name: '弛度速算（弛度-张力互算）',\n  nameEn: 'Sag Quick Calculation',\n  summary: '等高悬挂抛物线近似（小弛度假设）下弛度、张力与最大跨距互算。',\n  formula: [\n    '弛度 f = g·l²/(8T)',\n    '反算张力 T = g·l²/(8·f)',\n    '反算跨距上限 l_max = √(8·T·f_max/g)',\n  ],\n  references: [\n    '限值（TB 10009-2016 第 5.1.9 条，推荐性「不宜大于」口径）：链形悬挂接触线 150 mm、简单悬挂 250 mm、低速区段 350 mm',\n    '等高悬挂抛物线近似，适用于 f/l ≤ 1/10',\n  ],\n  scope: ['张力 T：1~40 kN', '跨距 l：5~80 m', '单位重 g：5~25 N/m'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/sag/',\n};\n","export { sagMeta } from './meta';\n\n/** 弛度计算参数。单位：张力 kN、跨距 m、单位重 N/m。 */\nexport interface SagInput {\n  /** 接触线/承力索张力 T，kN */\n  readonly tensionKN: number;\n  /** 跨距 l，m */\n  readonly spanM: number;\n  /** 单位长度重量 g，N/m */\n  readonly weightNPerM: number;\n}\n\n/** 弛度 f = g·l²/(8T)，mm */\nexport function sagMM(input: SagInput): number {\n  const { tensionKN, spanM, weightNPerM } = input;\n  if (!(tensionKN > 0)) throw new RangeError('张力必须为正，收到 ' + tensionKN + ' kN');\n  if (!(spanM > 0)) throw new RangeError('跨距必须为正，收到 ' + spanM + ' m');\n  if (!(weightNPerM >= 0)) throw new RangeError('单位重不能为负，收到 ' + weightNPerM + ' N/m');\n  const sagM = (weightNPerM * spanM * spanM) / (8 * tensionKN * 1e3);\n  return sagM * 1e3;\n}\n\n/** 反算张力：给定弛度求张力 T = g·l²/(8·f)，kN */\nexport function tensionFromSagKN(weightNPerM: number, spanM: number, sagMM: number): number {\n  if (!(sagMM > 0)) throw new RangeError('弛度必须为正，收到 ' + sagMM + ' mm');\n  const sagM = sagMM / 1e3;\n  return (weightNPerM * spanM * spanM) / (8 * sagM) / 1e3;\n}\n\n/** 反算最大跨距：给定张力与限值弛度 l_max = √(8·T·f_max/g)，m */\nexport function maxSpanFromSagM(weightNPerM: number, tensionKN: number, sagLimitMM: number): number {\n  if (!(tensionKN > 0)) throw new RangeError('张力必须为正，收到 ' + tensionKN + ' kN');\n  if (!(weightNPerM > 0)) throw new RangeError('单位重必须为正，收到 ' + weightNPerM + ' N/m');\n  if (!(sagLimitMM > 0)) throw new RangeError('限值弛度必须为正，收到 ' + sagLimitMM + ' mm');\n  const sagM = sagLimitMM / 1e3;\n  return Math.sqrt((8 * tensionKN * 1e3 * sagM) / weightNPerM);\n}\n"],"mappings":";AAEO,IAAM,UAA0B;AAAA,EACrC,MAAM;AAAA,EACN,QAAQ;AAAA,EACR,SAAS;AAAA,EACT,SAAS;AAAA,IACP;AAAA,IACA;AAAA,IACA;AAAA,EACF;AAAA,EACA,YAAY;AAAA,IACV;AAAA,IACA;AAAA,EACF;AAAA,EACA,OAAO,CAAC,+BAAgB,8BAAe,oCAAgB;AAAA,EACvD,YAAY;AAAA,EACZ,QAAQ;AACV;;;ACLO,SAAS,MAAM,OAAyB;AAC7C,QAAM,EAAE,WAAW,OAAO,YAAY,IAAI;AAC1C,MAAI,EAAE,YAAY,GAAI,OAAM,IAAI,WAAW,4DAAe,YAAY,KAAK;AAC3E,MAAI,EAAE,QAAQ,GAAI,OAAM,IAAI,WAAW,4DAAe,QAAQ,IAAI;AAClE,MAAI,EAAE,eAAe,GAAI,OAAM,IAAI,WAAW,kEAAgB,cAAc,MAAM;AAClF,QAAM,OAAQ,cAAc,QAAQ,SAAU,IAAI,YAAY;AAC9D,SAAO,OAAO;AAChB;AAGO,SAAS,iBAAiB,aAAqB,OAAeA,QAAuB;AAC1F,MAAI,EAAEA,SAAQ,GAAI,OAAM,IAAI,WAAW,4DAAeA,SAAQ,KAAK;AACnE,QAAM,OAAOA,SAAQ;AACrB,SAAQ,cAAc,QAAQ,SAAU,IAAI,QAAQ;AACtD;AAGO,SAAS,gBAAgB,aAAqB,WAAmB,YAA4B;AAClG,MAAI,EAAE,YAAY,GAAI,OAAM,IAAI,WAAW,4DAAe,YAAY,KAAK;AAC3E,MAAI,EAAE,cAAc,GAAI,OAAM,IAAI,WAAW,kEAAgB,cAAc,MAAM;AACjF,MAAI,EAAE,aAAa,GAAI,OAAM,IAAI,WAAW,wEAAiB,aAAa,KAAK;AAC/E,QAAM,OAAO,aAAa;AAC1B,SAAO,KAAK,KAAM,IAAI,YAAY,MAAM,OAAQ,WAAW;AAC7D;","names":["sagMM"]}

package/dist/{chunk-4344WWAF.cjs → chunk-R4IVRYJA.cjs}

@@ -24,6 +24,7 @@ var TEST_MOMENT_FACTOR = 1.5;
 function poleCapacityCheck(input) {
   const { section, contactWireTensionKN, messengerTensionKN, staggerMM, spanM, resultantHeightM, windPressurePa, poleWidthM, poleHeightM, wireWindLoadN } = input;
   if (!(contactWireTensionKN >= 0) || !(messengerTensionKN >= 0)) throw new RangeError("\u5F20\u529B\u4E0D\u80FD\u4E3A\u8D1F");
+  if (!(spanM > 0)) throw new RangeError("\u8DE8\u8DDD\u5FC5\u987B\u4E3A\u6B63\uFF0C\u6536\u5230 " + spanM + " m");
   const T = contactWireTensionKN + messengerTensionKN;
   const a = staggerMM / 1e3;
   const Fz = 4 * T * a / spanM;
@@ -55,4 +56,4 @@ function poleCapacityCheck(input) {
 
 
 exports.poleCapacityMeta = poleCapacityMeta; exports.STEEL_POLE_SERIES_KNM = STEEL_POLE_SERIES_KNM; exports.TEST_MOMENT_FACTOR = TEST_MOMENT_FACTOR; exports.poleCapacityCheck = poleCapacityCheck;
-//# sourceMappingURL=chunk-4344WWAF.cjs.map
+//# sourceMappingURL=chunk-R4IVRYJA.cjs.map

package/dist/chunk-R4IVRYJA.cjs.map

@@ -0,0 +1 @@
+{"version":3,"sources":["/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-R4IVRYJA.cjs","../src/pole-capacity/meta.ts","../src/pole-capacity/index.ts"],"names":[],"mappings":"AAAA;ACEO,IAAM,iBAAA,EAAmC;AAAA,EAC9C,IAAA,EAAM,kDAAA;AAAA,EACN,MAAA,EAAQ,+BAAA;AAAA,EACR,OAAA,EAAS,8OAAA;AAAA,EACT,OAAA,EAAS;AAAA,IACP,uGAAA;AAAA,IACA,2EAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,UAAA,EAAY;AAAA,IACV,uIAAA;AAAA,IACA,0LAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,KAAA,EAAO,CAAC,2BAAA,EAAc,2BAAA,EAAc,+BAAA,EAAkB,gCAAY,CAAA;AAAA,EAClE,UAAA,EAAY,sKAAA;AAAA,EACZ,MAAA,EAAQ;AACV,CAAA;ADAA;AACA;AEjBO,IAAM,sBAAA,EAAwB,CAAC,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,IAAA,EAAM,IAAA,EAAM,IAAI,CAAA;AAGhH,IAAM,mBAAA,EAAqB,GAAA;AAwC3B,SAAS,iBAAA,CAAkB,KAAA,EAA8C;AAC9E,EAAA,MAAM,EAAE,OAAA,EAAS,oBAAA,EAAsB,kBAAA,EAAoB,SAAA,EAAW,KAAA,EAAO,gBAAA,EAAkB,cAAA,EAAgB,UAAA,EAAY,WAAA,EAAa,cAAc,EAAA,EAAI,KAAA;AAC1J,EAAA,GAAA,CAAI,CAAA,CAAE,qBAAA,GAAwB,CAAA,EAAA,GAAM,CAAA,CAAE,mBAAA,GAAsB,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,sCAAQ,CAAA;AAC7F,EAAA,GAAA,CAAI,CAAA,CAAE,MAAA,EAAQ,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,0DAAA,EAAe,MAAA,EAAQ,IAAI,CAAA;AAClE,EAAA,MAAM,EAAA,EAAI,qBAAA,EAAuB,kBAAA;AACjC,EAAA,MAAM,EAAA,EAAI,UAAA,EAAY,GAAA;AACtB,EAAA,MAAM,GAAA,EAAM,EAAA,EAAI,EAAA,EAAI,EAAA,EAAK,KAAA;AACzB,EAAA,IAAI,EAAA;AACJ,EAAA,GAAA,CAAI,QAAA,IAAY,OAAA,EAAS;AACvB,IAAA,GAAA,CAAI,CAAA,CAAE,KAAA,CAAM,aAAA,GAAgB,KAAA,CAAM,aAAA,EAAe,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,kDAAU,CAAA;AACpF,IAAA,MAAM,GAAA,EAAM,EAAA,EAAI,MAAA,EAAS,KAAA,CAAM,YAAA;AAC/B,IAAA,GAAA,EAAK,IAAA,CAAK,GAAA,CAAI,GAAA,EAAK,EAAE,CAAA;AAAA,EACvB,EAAA,KAAO;AACL,IAAA,GAAA,EAAK,EAAA;AAAA,EACP;AACA,EAAA,MAAM,GAAA,EAAK,GAAA,EAAK,gBAAA;AAChB,EAAA,MAAM,GAAA,EAAM,eAAA,EAAiB,WAAA,EAAa,IAAA,CAAK,GAAA,CAAI,WAAA,EAAa,CAAC,EAAA,EAAI,EAAA,EAAK,GAAA;AAC1E,EAAA,MAAM,GAAA,EAAA,kBAAO,aAAA,UAAiB,GAAA,EAAA,EAAK,iBAAA,EAAoB,GAAA;AACvD,EAAA,MAAM,EAAA,EAAI,GAAA,EAAK,GAAA,EAAK,EAAA;AACpB,EAAA,MAAM,QAAA,EAAU,EAAA,EAAI,kBAAA;AACpB,EAAA,MAAM,KAAA,mBAAO,qBAAA,CAAsB,IAAA,CAAK,CAAC,CAAA,EAAA,GAAM,EAAA,GAAK,OAAO,CAAA,UAAK,MAAA;AAChE,EAAA,OAAO;AAAA,IACL,gBAAA,EAAkB,GAAA,EAAK,GAAA;AAAA,IACvB,aAAA,EAAe,CAAA;AAAA,IACf,cAAA,EAAgB,OAAA;AAAA,IAChB,SAAA,EAAW,KAAA,EAAO,IAAA,EAAM,KAAA,EAAO;AAAA,EACjC,CAAA;AACF;AFtBA;AACA;AACE;AACA;AACA;AACA;AACF,mMAAC","file":"/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-R4IVRYJA.cjs","sourcesContent":[null,"import type { CalculatorMeta } from '../types';\n\nexport const poleCapacityMeta: CalculatorMeta = {\n  name: '支柱容量选型校核',\n  nameEn: 'Mast Capacity Selection Check',\n  summary: '容量比较法：悬挂水平力与支柱风载合成工作弯矩，对照 GB/T 25020.1 钢支柱检验弯矩系列选型。',\n  formula: [\n    '直线之字力 F_z = 4(T_j+T_c)·a/l；曲线力 F_q = (T_j+T_c)·l/R',\n    '工作弯矩 M = F_h·h_e + P·b·h²/2 + F_wl·h_e',\n    '承载力检验弯矩 = 1.5 × 标称容量（25020.1 表 A.2 表值规律）',\n  ],\n  references: [\n    '钢柱直接依据：GB/T 25020.1-2025 第 5.1.1 条 + 附录 A 检验弯矩系列',\n    '同口径混凝土柱条款：TB/T 2286-2020 第 5.9.2 条（荷载矢量组合不大于检验弯矩）',\n    '分项系数极限状态法（GB/T 32578-2016 6.3.3 表 15）为设计正式口径，不可混用',\n  ],\n  scope: ['张力：5~45 kN', '跨距：30~90 m', '风压：100~1500 Pa', '支柱高：5~20 m'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/pole-capacity/',\n};\n","export { poleCapacityMeta } from './meta';\n\n/** GB/T 25020.1-2025 格构式钢支柱标称容量系列（表 A.2），kN·m */\nexport const STEEL_POLE_SERIES_KNM = [150, 200, 250, 300, 350, 400, 450, 500, 550, 600, 650, 750, 900, 1050, 1200, 1500] as const;\n\n/** 承载力检验弯矩 = 1.5 × 标称容量（25020.1 表 A.2 表值规律） */\nexport const TEST_MOMENT_FACTOR = 1.5;\n\n/** 支柱容量校核输入。单位：kN、m、mm、Pa。 */\nexport interface PoleCapacityInput {\n  /** 区段类型 */\n  readonly section: 'line' | 'curve';\n  /** 接触线张力 T_j，kN */\n  readonly contactWireTensionKN: number;\n  /** 承力索张力 T_c，kN */\n  readonly messengerTensionKN: number;\n  /** 拉出值 a，mm */\n  readonly staggerMM: number;\n  /** 跨距 l，m */\n  readonly spanM: number;\n  /** 曲线半径 R，m（曲线区段） */\n  readonly curveRadiusM?: number;\n  /** 水平力合力作用高度 h_e，m */\n  readonly resultantHeightM: number;\n  /** 设计最大风压 P，Pa */\n  readonly windPressurePa: number;\n  /** 支柱迎风宽度 b，m */\n  readonly poleWidthM: number;\n  /** 支柱高度 h，m */\n  readonly poleHeightM: number;\n  /** 线索风载 F_wl，N */\n  readonly wireWindLoadN?: number;\n}\n\nexport interface PoleCapacityResult {\n  /** 悬挂水平力 F_h，N */\n  readonly horizontalForceN: number;\n  /** 工作弯矩 M，kN·m */\n  readonly workMomentKNM: number;\n  /** 折合标称容量（÷1.5），kN·m */\n  readonly nominalNeedKNM: number;\n  /** 选型结果 */\n  readonly selection: string | null;\n}\n\n/** 支柱容量选型（容量比较法，TB/T 2286 5.9.2 检验弯矩口径；钢柱 25020.1 5.1.1+附录A） */\nexport function poleCapacityCheck(input: PoleCapacityInput): PoleCapacityResult {\n  const { section, contactWireTensionKN, messengerTensionKN, staggerMM, spanM, resultantHeightM, windPressurePa, poleWidthM, poleHeightM, wireWindLoadN } = input;\n  if (!(contactWireTensionKN >= 0) || !(messengerTensionKN >= 0)) throw new RangeError('张力不能为负');\n  if (!(spanM > 0)) throw new RangeError('跨距必须为正，收到 ' + spanM + ' m');\n  const T = contactWireTensionKN + messengerTensionKN;\n  const a = staggerMM / 1e3;\n  const Fz = (4 * T * a) / spanM; // kN\n  let Fh: number;\n  if (section === 'curve') {\n    if (!(input.curveRadiusM && input.curveRadiusM > 0)) throw new RangeError('曲线半径必须为正');\n    const Fq = (T * spanM) / input.curveRadiusM;\n    Fh = Math.abs(Fq - Fz);\n  } else {\n    Fh = Fz;\n  }\n  const M1 = Fh * resultantHeightM; // 悬挂水平力矩 kN·m\n  const M2 = (windPressurePa * poleWidthM * Math.pow(poleHeightM, 2) / 2) / 1e3; // 支柱风载矩\n  const M3 = ((wireWindLoadN ?? 0) * resultantHeightM) / 1e3;\n  const M = M1 + M2 + M3;\n  const nomNeed = M / TEST_MOMENT_FACTOR;\n  const pick = STEEL_POLE_SERIES_KNM.find((n) => n >= nomNeed) ?? null;\n  return {\n    horizontalForceN: Fh * 1e3,\n    workMomentKNM: M,\n    nominalNeedKNM: nomNeed,\n    selection: pick ? 'G' + pick : null,\n  };\n}\n"]}

package/dist/creepage/index.cjs

@@ -4,12 +4,12 @@
 
 
 
-var _chunkLBGUOTCJcjs = require('../chunk-LBGUOTCJ.cjs');
+var _chunkAVQ4F6DFcjs = require('../chunk-AVQ4F6DF.cjs');
 
 
 
 
 
 
-exports.CREEPAGE_FLOOR_GENERAL = _chunkLBGUOTCJcjs.CREEPAGE_FLOOR_GENERAL; exports.CREEPAGE_FLOOR_VCUT = _chunkLBGUOTCJcjs.CREEPAGE_FLOOR_VCUT; exports.USCD_BANDS = _chunkLBGUOTCJcjs.USCD_BANDS; exports.creepageCheck = _chunkLBGUOTCJcjs.creepageCheck; exports.creepageMeta = _chunkLBGUOTCJcjs.creepageMeta;
+exports.CREEPAGE_FLOOR_GENERAL = _chunkAVQ4F6DFcjs.CREEPAGE_FLOOR_GENERAL; exports.CREEPAGE_FLOOR_VCUT = _chunkAVQ4F6DFcjs.CREEPAGE_FLOOR_VCUT; exports.USCD_BANDS = _chunkAVQ4F6DFcjs.USCD_BANDS; exports.creepageCheck = _chunkAVQ4F6DFcjs.creepageCheck; exports.creepageMeta = _chunkAVQ4F6DFcjs.creepageMeta;
 //# sourceMappingURL=index.cjs.map

package/dist/creepage/index.js

@@ -4,7 +4,7 @@ import {
   USCD_BANDS,
   creepageCheck,
   creepageMeta
-} from "../chunk-CLVLOLUJ.js";
+} from "../chunk-3LUPNS4U.js";
 export {
   CREEPAGE_FLOOR_GENERAL,
   CREEPAGE_FLOOR_VCUT,

package/dist/index.cjs

@@ -25,14 +25,14 @@ var _chunkNBHEOJ5Acjs = require('./chunk-NBHEOJ5A.cjs');
 
 
 
-var _chunk5INEDXRYcjs = require('./chunk-5INEDXRY.cjs');
 
+var _chunkFVESJBUDcjs = require('./chunk-FVESJBUD.cjs');
 
 
 
 
 
-var _chunkFVESJBUDcjs = require('./chunk-FVESJBUD.cjs');
+var _chunk5INEDXRYcjs = require('./chunk-5INEDXRY.cjs');
 
 
 
@@ -47,34 +47,34 @@ var _chunk4UU7WA7Ncjs = require('./chunk-4UU7WA7N.cjs');
 
 
 
-var _chunkJ2UXRMTUcjs = require('./chunk-J2UXRMTU.cjs');
 
+var _chunkRPKDEFSJcjs = require('./chunk-RPKDEFSJ.cjs');
 
 
 
 
 
 
-var _chunkRPKDEFSJcjs = require('./chunk-RPKDEFSJ.cjs');
+var _chunkP6KUGPHDcjs = require('./chunk-P6KUGPHD.cjs');
 
 
 
 
 
 
-var _chunkP6KUGPHDcjs = require('./chunk-P6KUGPHD.cjs');
+var _chunkJ2UXRMTUcjs = require('./chunk-J2UXRMTU.cjs');
 
 
 
 
 
-var _chunk4344WWAFcjs = require('./chunk-4344WWAF.cjs');
+var _chunkR4IVRYJAcjs = require('./chunk-R4IVRYJA.cjs');
 
 
 
 
 
-var _chunkPYNVEHGRcjs = require('./chunk-PYNVEHGR.cjs');
+var _chunkCF663UNGcjs = require('./chunk-CF663UNG.cjs');
 
 
 
@@ -105,12 +105,12 @@ var _chunkCSLI5HEJcjs = require('./chunk-CSLI5HEJ.cjs');
 
 
 
-var _chunkHXALVJ4Gcjs = require('./chunk-HXALVJ4G.cjs');
 
+var _chunkWGTOBRYVcjs = require('./chunk-WGTOBRYV.cjs');
 
 
 
-var _chunkWGTOBRYVcjs = require('./chunk-WGTOBRYV.cjs');
+var _chunkHXALVJ4Gcjs = require('./chunk-HXALVJ4G.cjs');
 
 
 
@@ -127,7 +127,7 @@ var _chunkDGO2DCO5cjs = require('./chunk-DGO2DCO5.cjs');
 
 
 
-var _chunkLBGUOTCJcjs = require('./chunk-LBGUOTCJ.cjs');
+var _chunkAVQ4F6DFcjs = require('./chunk-AVQ4F6DF.cjs');
 
 
 
@@ -333,5 +333,5 @@ function findAmpacityA(params) {
 
 
 
-exports.AIR_DENSITY_KG_PER_M3 = _chunkFVESJBUDcjs.AIR_DENSITY_KG_PER_M3; exports.ASSEMBLY_TOLERANCE_MM = _chunkWGTOBRYVcjs.ASSEMBLY_TOLERANCE_MM; exports.CONVENTIONAL_MARGIN_MM = _chunk5Q6IASB2cjs.CONVENTIONAL_MARGIN_MM; exports.COPPER_ALLOY_ALPHA_PER_DEG_C = COPPER_ALLOY_ALPHA_PER_DEG_C; exports.COPPER_ALPHA_PER_DEG_C = _chunkDGO2DCO5cjs.COPPER_ALPHA_PER_DEG_C; exports.CREEPAGE_FLOOR_GENERAL = _chunkLBGUOTCJcjs.CREEPAGE_FLOOR_GENERAL; exports.CREEPAGE_FLOOR_VCUT = _chunkLBGUOTCJcjs.CREEPAGE_FLOOR_VCUT; exports.DEFAULT_BASE_AMBIENT_TEMP_DEG_C = _chunkNBFOB2PIcjs.DEFAULT_BASE_AMBIENT_TEMP_DEG_C; exports.DEFAULT_ICE_DENSITY_KG_PER_M3 = _chunkP6KUGPHDcjs.DEFAULT_ICE_DENSITY_KG_PER_M3; exports.DEFAULT_MIN_END_VOLTAGE_V = _chunkRVP3IU2Lcjs.DEFAULT_MIN_END_VOLTAGE_V; exports.DEFAULT_PANTOGRAPH_HEIGHT_M = _chunk4UU7WA7Ncjs.DEFAULT_PANTOGRAPH_HEIGHT_M; exports.DEFAULT_REPLACEMENT_THRESHOLD_PERCENT = _chunk5INEDXRYcjs.DEFAULT_REPLACEMENT_THRESHOLD_PERCENT; exports.DEFAULT_WARN_THRESHOLD = _chunkNBHEOJ5Acjs.DEFAULT_WARN_THRESHOLD; exports.G0 = _chunkP6KUGPHDcjs.G0; exports.IACS_RESISTIVITY_OHM_MM2_PER_M = _chunkDGO2DCO5cjs.IACS_RESISTIVITY_OHM_MM2_PER_M; exports.MIN_MARGIN_MM = _chunk5Q6IASB2cjs.MIN_MARGIN_MM; exports.REFERENCE_DENSITY_G_PER_CM3 = REFERENCE_DENSITY_G_PER_CM3; exports.REF_TARGET_COEFF = _chunkRPKDEFSJcjs.REF_TARGET_COEFF; exports.REF_TARGET_OFFSET_N = _chunkRPKDEFSJcjs.REF_TARGET_OFFSET_N; exports.STANDARD_GAUGE_M = _chunk4UU7WA7Ncjs.STANDARD_GAUGE_M; exports.STANDARD_UNIT_WEIGHT_KG_PER_KM = STANDARD_UNIT_WEIGHT_KG_PER_KM; exports.STEEL_POLE_SERIES_KNM = _chunk4344WWAFcjs.STEEL_POLE_SERIES_KNM; exports.TB2809_AMPACITY_A = TB2809_AMPACITY_A; exports.TB2809_WIRE_PARAMS = _chunkMTAYG3U2cjs.TB2809_WIRE_PARAMS; exports.TENSION_DIFF_RATIO = _chunkCSLI5HEJcjs.TENSION_DIFF_RATIO; exports.TEST_MOMENT_FACTOR = _chunk4344WWAFcjs.TEST_MOMENT_FACTOR; exports.TRANSMISSION_RATIOS = _chunk5Q6IASB2cjs.TRANSMISSION_RATIOS; exports.USCD_BANDS = _chunkLBGUOTCJcjs.USCD_BANDS; exports.WIRE_PRESETS = WIRE_PRESETS; exports.ampacityDeratingFactor = _chunkNBFOB2PIcjs.ampacityDeratingFactor; exports.ampacityMeta = _chunkNBFOB2PIcjs.ampacityMeta; exports.anchorLengthCheck = _chunkCSLI5HEJcjs.anchorLengthCheck; exports.anchorLengthMeta = _chunkCSLI5HEJcjs.anchorLengthMeta; exports.assessContactForce = _chunkRPKDEFSJcjs.assessContactForce; exports.bValue = _chunkHXALVJ4Gcjs.bValue; exports.bvalueMeta = _chunkHXALVJ4Gcjs.bvalueMeta; exports.cantShiftM = _chunk4UU7WA7Ncjs.cantShiftM; exports.cantileverCut = _chunkWGTOBRYVcjs.cantileverCut; exports.cantileverMeta = _chunkWGTOBRYVcjs.cantileverMeta; exports.copperMeta = _chunkMTAYG3U2cjs.copperMeta; exports.creepageCheck = _chunkLBGUOTCJcjs.creepageCheck; exports.creepageMeta = _chunkLBGUOTCJcjs.creepageMeta; exports.crossSpanAnalyze = _chunkX25CXRVEcjs.crossSpanAnalyze; exports.crossSpanMeta = _chunkX25CXRVEcjs.crossSpanMeta; exports.curveStaggerCheck = _chunk4UU7WA7Ncjs.curveStaggerCheck; exports.curveStaggerMeta = _chunk4UU7WA7Ncjs.curveStaggerMeta; exports.deratedAmpacityA = _chunkNBFOB2PIcjs.deratedAmpacityA; exports.deriveLinearMassKgPerM = deriveLinearMassKgPerM; exports.dropperLengths = _chunkJ2UXRMTUcjs.dropperLengths; exports.dropperMeta = _chunkJ2UXRMTUcjs.dropperMeta; exports.dropperPositionsM = _chunkJ2UXRMTUcjs.dropperPositionsM; exports.elongationMM = _chunk5Q6IASB2cjs.elongationMM; exports.equivalentSpanM = _chunk3ERFRRHZcjs.equivalentSpanM; exports.findAmpacityA = findAmpacityA; exports.findWirePreset = findWirePreset; exports.forceMeta = _chunkRPKDEFSJcjs.forceMeta; exports.iceLoadNPerM = _chunkP6KUGPHDcjs.iceLoadNPerM; exports.icingCheck = _chunkP6KUGPHDcjs.icingCheck; exports.icingMeta = _chunkP6KUGPHDcjs.icingMeta; exports.kmHToMPerS = _chunkNBHEOJ5Acjs.kmHToMPerS; exports.maxParabolaSagM = _chunkJ2UXRMTUcjs.maxParabolaSagM; exports.maxSpanFromSagM = _chunkPYNVEHGRcjs.maxSpanFromSagM; exports.naturalFrequencyHz = _chunkNBHEOJ5Acjs.naturalFrequencyHz; exports.parabolaSagM = _chunkJ2UXRMTUcjs.parabolaSagM; exports.poleCapacityCheck = _chunk4344WWAFcjs.poleCapacityCheck; exports.poleCapacityMeta = _chunk4344WWAFcjs.poleCapacityMeta; exports.referenceTargetForceN = _chunkRPKDEFSJcjs.referenceTargetForceN; exports.requiredStrokeMM = _chunk5Q6IASB2cjs.requiredStrokeMM; exports.resistanceAtTempOhmPerKm = _chunkDGO2DCO5cjs.resistanceAtTempOhmPerKm; exports.sagM = _chunk3ERFRRHZcjs.sagM; exports.sagMM = _chunkPYNVEHGRcjs.sagMM; exports.sagMeta = _chunkPYNVEHGRcjs.sagMeta; exports.sectionFromDiameterMM2 = _chunk5INEDXRYcjs.sectionFromDiameterMM2; exports.shortCircuitCheck = _chunkNBFOB2PIcjs.shortCircuitCheck; exports.shortCircuitMinSectionMM2 = _chunkNBFOB2PIcjs.shortCircuitMinSectionMM2; exports.solveTensionN = _chunk3ERFRRHZcjs.solveTensionN; exports.stateCoefficientK = _chunk3ERFRRHZcjs.stateCoefficientK; exports.statisticalForcesN = _chunkRPKDEFSJcjs.statisticalForcesN; exports.steadyArmAngleDeg = _chunk57J7I6JAcjs.steadyArmAngleDeg; exports.steadyArmCheck = _chunk57J7I6JAcjs.steadyArmCheck; exports.steadyArmMeta = _chunk57J7I6JAcjs.steadyArmMeta; exports.strokeCheck = _chunk5Q6IASB2cjs.strokeCheck; exports.strokeMeta = _chunk5Q6IASB2cjs.strokeMeta; exports.tensionAt = _chunk3ERFRRHZcjs.tensionAt; exports.tensionCurve = _chunk3ERFRRHZcjs.tensionCurve; exports.tensionFromSagKN = _chunkPYNVEHGRcjs.tensionFromSagKN; exports.tensionMeta = _chunk3ERFRRHZcjs.tensionMeta; exports.unitWeightToKgPerM = unitWeightToKgPerM; exports.versineM = _chunk4UU7WA7Ncjs.versineM; exports.voltageDropCheck = _chunkRVP3IU2Lcjs.voltageDropCheck; exports.voltageDropMeta = _chunkRVP3IU2Lcjs.voltageDropMeta; exports.wavePropagationSpeedMPerS = _chunkNBHEOJ5Acjs.wavePropagationSpeedMPerS; exports.waveSpeedCheck = _chunkNBHEOJ5Acjs.waveSpeedCheck; exports.wavespeedMeta = _chunkNBHEOJ5Acjs.wavespeedMeta; exports.wearMeta = _chunk5INEDXRYcjs.wearMeta; exports.wearRatio = _chunk5INEDXRYcjs.wearRatio; exports.weightOfPresetNPerM = weightOfPresetNPerM; exports.weightPerLengthNPerM = weightPerLengthNPerM; exports.windClearanceCheck = _chunkFVESJBUDcjs.windClearanceCheck; exports.windDeflectionM = _chunkFVESJBUDcjs.windDeflectionM; exports.windLoadNPerM = _chunkFVESJBUDcjs.windLoadNPerM; exports.windMeta = _chunkFVESJBUDcjs.windMeta; exports.wireLookup = _chunkMTAYG3U2cjs.wireLookup;
+exports.AIR_DENSITY_KG_PER_M3 = _chunkFVESJBUDcjs.AIR_DENSITY_KG_PER_M3; exports.ASSEMBLY_TOLERANCE_MM = _chunkWGTOBRYVcjs.ASSEMBLY_TOLERANCE_MM; exports.CONVENTIONAL_MARGIN_MM = _chunk5Q6IASB2cjs.CONVENTIONAL_MARGIN_MM; exports.COPPER_ALLOY_ALPHA_PER_DEG_C = COPPER_ALLOY_ALPHA_PER_DEG_C; exports.COPPER_ALPHA_PER_DEG_C = _chunkDGO2DCO5cjs.COPPER_ALPHA_PER_DEG_C; exports.CREEPAGE_FLOOR_GENERAL = _chunkAVQ4F6DFcjs.CREEPAGE_FLOOR_GENERAL; exports.CREEPAGE_FLOOR_VCUT = _chunkAVQ4F6DFcjs.CREEPAGE_FLOOR_VCUT; exports.DEFAULT_BASE_AMBIENT_TEMP_DEG_C = _chunkNBFOB2PIcjs.DEFAULT_BASE_AMBIENT_TEMP_DEG_C; exports.DEFAULT_ICE_DENSITY_KG_PER_M3 = _chunkP6KUGPHDcjs.DEFAULT_ICE_DENSITY_KG_PER_M3; exports.DEFAULT_MIN_END_VOLTAGE_V = _chunkRVP3IU2Lcjs.DEFAULT_MIN_END_VOLTAGE_V; exports.DEFAULT_PANTOGRAPH_HEIGHT_M = _chunk4UU7WA7Ncjs.DEFAULT_PANTOGRAPH_HEIGHT_M; exports.DEFAULT_REPLACEMENT_THRESHOLD_PERCENT = _chunk5INEDXRYcjs.DEFAULT_REPLACEMENT_THRESHOLD_PERCENT; exports.DEFAULT_WARN_THRESHOLD = _chunkNBHEOJ5Acjs.DEFAULT_WARN_THRESHOLD; exports.G0 = _chunkP6KUGPHDcjs.G0; exports.IACS_RESISTIVITY_OHM_MM2_PER_M = _chunkDGO2DCO5cjs.IACS_RESISTIVITY_OHM_MM2_PER_M; exports.MIN_MARGIN_MM = _chunk5Q6IASB2cjs.MIN_MARGIN_MM; exports.REFERENCE_DENSITY_G_PER_CM3 = REFERENCE_DENSITY_G_PER_CM3; exports.REF_TARGET_COEFF = _chunkRPKDEFSJcjs.REF_TARGET_COEFF; exports.REF_TARGET_OFFSET_N = _chunkRPKDEFSJcjs.REF_TARGET_OFFSET_N; exports.STANDARD_GAUGE_M = _chunk4UU7WA7Ncjs.STANDARD_GAUGE_M; exports.STANDARD_UNIT_WEIGHT_KG_PER_KM = STANDARD_UNIT_WEIGHT_KG_PER_KM; exports.STEEL_POLE_SERIES_KNM = _chunkR4IVRYJAcjs.STEEL_POLE_SERIES_KNM; exports.TB2809_AMPACITY_A = TB2809_AMPACITY_A; exports.TB2809_WIRE_PARAMS = _chunkMTAYG3U2cjs.TB2809_WIRE_PARAMS; exports.TENSION_DIFF_RATIO = _chunkCSLI5HEJcjs.TENSION_DIFF_RATIO; exports.TEST_MOMENT_FACTOR = _chunkR4IVRYJAcjs.TEST_MOMENT_FACTOR; exports.TRANSMISSION_RATIOS = _chunk5Q6IASB2cjs.TRANSMISSION_RATIOS; exports.USCD_BANDS = _chunkAVQ4F6DFcjs.USCD_BANDS; exports.WIRE_PRESETS = WIRE_PRESETS; exports.ampacityDeratingFactor = _chunkNBFOB2PIcjs.ampacityDeratingFactor; exports.ampacityMeta = _chunkNBFOB2PIcjs.ampacityMeta; exports.anchorLengthCheck = _chunkCSLI5HEJcjs.anchorLengthCheck; exports.anchorLengthMeta = _chunkCSLI5HEJcjs.anchorLengthMeta; exports.assessContactForce = _chunkRPKDEFSJcjs.assessContactForce; exports.bValue = _chunkHXALVJ4Gcjs.bValue; exports.bvalueMeta = _chunkHXALVJ4Gcjs.bvalueMeta; exports.cantShiftM = _chunk4UU7WA7Ncjs.cantShiftM; exports.cantileverCut = _chunkWGTOBRYVcjs.cantileverCut; exports.cantileverMeta = _chunkWGTOBRYVcjs.cantileverMeta; exports.copperMeta = _chunkMTAYG3U2cjs.copperMeta; exports.creepageCheck = _chunkAVQ4F6DFcjs.creepageCheck; exports.creepageMeta = _chunkAVQ4F6DFcjs.creepageMeta; exports.crossSpanAnalyze = _chunkX25CXRVEcjs.crossSpanAnalyze; exports.crossSpanMeta = _chunkX25CXRVEcjs.crossSpanMeta; exports.curveStaggerCheck = _chunk4UU7WA7Ncjs.curveStaggerCheck; exports.curveStaggerMeta = _chunk4UU7WA7Ncjs.curveStaggerMeta; exports.deratedAmpacityA = _chunkNBFOB2PIcjs.deratedAmpacityA; exports.deriveLinearMassKgPerM = deriveLinearMassKgPerM; exports.dropperLengths = _chunkJ2UXRMTUcjs.dropperLengths; exports.dropperMeta = _chunkJ2UXRMTUcjs.dropperMeta; exports.dropperPositionsM = _chunkJ2UXRMTUcjs.dropperPositionsM; exports.elongationMM = _chunk5Q6IASB2cjs.elongationMM; exports.equivalentSpanM = _chunk3ERFRRHZcjs.equivalentSpanM; exports.findAmpacityA = findAmpacityA; exports.findWirePreset = findWirePreset; exports.forceMeta = _chunkRPKDEFSJcjs.forceMeta; exports.iceLoadNPerM = _chunkP6KUGPHDcjs.iceLoadNPerM; exports.icingCheck = _chunkP6KUGPHDcjs.icingCheck; exports.icingMeta = _chunkP6KUGPHDcjs.icingMeta; exports.kmHToMPerS = _chunkNBHEOJ5Acjs.kmHToMPerS; exports.maxParabolaSagM = _chunkJ2UXRMTUcjs.maxParabolaSagM; exports.maxSpanFromSagM = _chunkCF663UNGcjs.maxSpanFromSagM; exports.naturalFrequencyHz = _chunkNBHEOJ5Acjs.naturalFrequencyHz; exports.parabolaSagM = _chunkJ2UXRMTUcjs.parabolaSagM; exports.poleCapacityCheck = _chunkR4IVRYJAcjs.poleCapacityCheck; exports.poleCapacityMeta = _chunkR4IVRYJAcjs.poleCapacityMeta; exports.referenceTargetForceN = _chunkRPKDEFSJcjs.referenceTargetForceN; exports.requiredStrokeMM = _chunk5Q6IASB2cjs.requiredStrokeMM; exports.resistanceAtTempOhmPerKm = _chunkDGO2DCO5cjs.resistanceAtTempOhmPerKm; exports.sagM = _chunk3ERFRRHZcjs.sagM; exports.sagMM = _chunkCF663UNGcjs.sagMM; exports.sagMeta = _chunkCF663UNGcjs.sagMeta; exports.sectionFromDiameterMM2 = _chunk5INEDXRYcjs.sectionFromDiameterMM2; exports.shortCircuitCheck = _chunkNBFOB2PIcjs.shortCircuitCheck; exports.shortCircuitMinSectionMM2 = _chunkNBFOB2PIcjs.shortCircuitMinSectionMM2; exports.solveTensionN = _chunk3ERFRRHZcjs.solveTensionN; exports.stateCoefficientK = _chunk3ERFRRHZcjs.stateCoefficientK; exports.statisticalForcesN = _chunkRPKDEFSJcjs.statisticalForcesN; exports.steadyArmAngleDeg = _chunk57J7I6JAcjs.steadyArmAngleDeg; exports.steadyArmCheck = _chunk57J7I6JAcjs.steadyArmCheck; exports.steadyArmMeta = _chunk57J7I6JAcjs.steadyArmMeta; exports.strokeCheck = _chunk5Q6IASB2cjs.strokeCheck; exports.strokeMeta = _chunk5Q6IASB2cjs.strokeMeta; exports.tensionAt = _chunk3ERFRRHZcjs.tensionAt; exports.tensionCurve = _chunk3ERFRRHZcjs.tensionCurve; exports.tensionFromSagKN = _chunkCF663UNGcjs.tensionFromSagKN; exports.tensionMeta = _chunk3ERFRRHZcjs.tensionMeta; exports.unitWeightToKgPerM = unitWeightToKgPerM; exports.versineM = _chunk4UU7WA7Ncjs.versineM; exports.voltageDropCheck = _chunkRVP3IU2Lcjs.voltageDropCheck; exports.voltageDropMeta = _chunkRVP3IU2Lcjs.voltageDropMeta; exports.wavePropagationSpeedMPerS = _chunkNBHEOJ5Acjs.wavePropagationSpeedMPerS; exports.waveSpeedCheck = _chunkNBHEOJ5Acjs.waveSpeedCheck; exports.wavespeedMeta = _chunkNBHEOJ5Acjs.wavespeedMeta; exports.wearMeta = _chunk5INEDXRYcjs.wearMeta; exports.wearRatio = _chunk5INEDXRYcjs.wearRatio; exports.weightOfPresetNPerM = weightOfPresetNPerM; exports.weightPerLengthNPerM = weightPerLengthNPerM; exports.windClearanceCheck = _chunkFVESJBUDcjs.windClearanceCheck; exports.windDeflectionM = _chunkFVESJBUDcjs.windDeflectionM; exports.windLoadNPerM = _chunkFVESJBUDcjs.windLoadNPerM; exports.windMeta = _chunkFVESJBUDcjs.windMeta; exports.wireLookup = _chunkMTAYG3U2cjs.wireLookup;
 //# sourceMappingURL=index.cjs.map

package/dist/index.cjs.map

@@ -1 +1 @@
-{"version":3,"sources":["/home/runner/work/ocs-calculators/ocs-calculators/dist/index.cjs","../src/data/wire-specs.ts","../src/data/tb2809-ampacity.ts"],"names":[],"mappings":"AAAA;AACE;AACA;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACF,wDAA6B;AAC7B;AACA;AC5FO,IAAM,4BAAA,EAA8B,IAAA;AAUpC,IAAM,+BAAA,EAAyE;AAAA,EACpF,OAAA,EAAS,IAAA;AAAA,EACT,OAAA,EAAS,IAAA;AAAA,EACT,OAAA,EAAS;AACX,CAAA;AAGO,SAAS,kBAAA,CAAmB,OAAA,EAAyB;AAC1D,EAAA,OAAO,QAAA,EAAU,GAAA;AACnB;AAYO,SAAS,sBAAA,CACd,eAAA,EACA,eAAA,EAAyB,2BAAA,EACjB;AAER,EAAA,OAAO,gBAAA,EAAkB,KAAA,EAAO,eAAA,EAAiB,GAAA;AACnD;AAGO,IAAM,6BAAA,EAA+B,KAAA;AAErC,IAAM,aAAA,EAAoC;AAAA,EAC/C;AAAA,IACE,EAAA,EAAI,SAAA;AAAA,IACJ,IAAA,EAAM,sCAAA;AAAA,IACN,MAAA,EAAQ,4BAAA;AAAA,IACR,eAAA,EAAiB,GAAA;AAAA,IACjB,oBAAA,EAAsB,GAAA;AAAA,IACtB,iBAAA,EAAmB,GAAA;AAAA,IACnB,gBAAA,EAAkB,4BAAA;AAAA,IAClB,gBAAA,EAAkB,kBAAA,CAAmB,8BAAA,CAA+B,OAAO;AAAA,EAC7E,CAAA;AAAA,EACA;AAAA,IACE,EAAA,EAAI,SAAA;AAAA,IACJ,IAAA,EAAM,sCAAA;AAAA,IACN,MAAA,EAAQ,4BAAA;AAAA,IACR,eAAA,EAAiB,GAAA;AAAA,IACjB,oBAAA,EAAsB,GAAA;AAAA,IACtB,iBAAA,EAAmB,GAAA;AAAA,IACnB,gBAAA,EAAkB,4BAAA;AAAA,IAClB,gBAAA,EAAkB,kBAAA,CAAmB,8BAAA,CAA+B,OAAO;AAAA,EAC7E,CAAA;AAAA,EACA;AAAA,IACE,EAAA,EAAI,SAAA;AAAA,IACJ,IAAA,EAAM,sCAAA;AAAA,IACN,MAAA,EAAQ,4BAAA;AAAA,IACR,eAAA,EAAiB,GAAA;AAAA,IACjB,oBAAA,EAAsB,GAAA;AAAA,IACtB,iBAAA,EAAmB,GAAA;AAAA,IACnB,gBAAA,EAAkB,4BAAA;AAAA,IAClB,gBAAA,EAAkB,kBAAA,CAAmB,8BAAA,CAA+B,OAAO;AAAA,EAC7E;AACF,CAAA;AAGO,SAAS,cAAA,CAAe,EAAA,EAAkC;AAC/D,EAAA,OAAO,YAAA,CAAa,IAAA,CAAK,CAAC,CAAA,EAAA,GAAM,CAAA,CAAE,GAAA,IAAO,EAAE,CAAA;AAC7C;AAMO,SAAS,oBAAA,CAAqB,gBAAA,EAAkC;AACrE,EAAA,OAAO,iBAAA,EAAmB,oBAAA;AAC5B;AAKO,SAAS,mBAAA,CAAoB,IAAA,EAAwB;AAC1D,EAAA,OAAO,oBAAA,CAAqB,IAAA,CAAK,gBAAgB,CAAA;AACnD;ADsDA;AACA;AEnJA,IAAM,EAAA,EAAI,CACR,IAAA,EACA,UAAA,EACA,QAAA,EACA,QAAA,EACA,SAAA,EACA,SAAA,EACA,UAAA,EAAA,GACoB;AACpB,EAAA,MAAM,WAAA,EAAuE;AAAA,IAC3E,CAAC,WAAA,EAAa,QAAQ,CAAA;AAAA,IACtB,CAAC,YAAA,EAAc,SAAS,CAAA;AAAA,IACxB,CAAC,YAAA,EAAc,SAAS,CAAA;AAAA,IACxB,CAAC,aAAA,EAAe,UAAU;AAAA,EAC5B,CAAA;AACA,EAAA,MAAM,IAAA,EAAuB,CAAC,CAAA;AAC9B,EAAA,IAAA,CAAA,MAAW,QAAA,GAAW,QAAA,EAAU;AAC9B,IAAA,IAAA,CAAA,MAAW,CAAC,SAAA,EAAW,IAAI,EAAA,GAAK,UAAA,EAAY;AAC1C,MAAA,MAAM,MAAA,EAAQ,QAAA,IAAY,IAAA,EAAM,IAAA,CAAK,CAAC,EAAA,EAAI,IAAA,CAAK,CAAC,CAAA;AAChD,MAAA,GAAA,CAAI,IAAA,CAAK;AAAA,QACP,IAAA;AAAA,QACA,UAAA;AAAA,QACA,eAAA,EAAiB,OAAA;AAAA,QACjB,SAAA;AAAA,QACA,SAAA,mBAAW,KAAA,UAAS;AAAA,MACtB,CAAC,CAAA;AAAA,IACH;AAAA,EACF;AACA,EAAA,OAAO,GAAA;AACT,CAAA;AAEO,IAAM,kBAAA,EAA8C;AAAA,EACzD,GAAG,CAAA,CAAE,IAAA,EAAM,QAAA,EAAK,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,IAAA,EAAM,IAAI,CAAA,EAAG,CAAC,IAAA,EAAM,IAAI,CAAC,CAAA;AAAA,EAC9E,GAAG,CAAA,CAAE,KAAA,EAAO,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC5E,GAAG,CAAA,CAAE,KAAA,EAAO,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC5E,GAAG,CAAA,CAAE,MAAA,EAAQ,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC7E,GAAG,CAAA,CAAE,MAAA,EAAQ,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC7E,GAAG,CAAA,CAAE,KAAA,EAAO,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC5E,GAAG,CAAA,CAAE,MAAA,EAAQ,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC7E,GAAG,CAAA,CAAE,MAAA,EAAQ,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC7E,GAAG,CAAA,CAAE,MAAA,EAAQ,oBAAA,EAAO,CAAC,GAAG,CAAA,EAAG,CAAC,IAAA,EAAM,GAAG,CAAA,EAAG,CAAC,IAAA,EAAM,GAAG,CAAA,EAAG,CAAC,IAAA,EAAM,GAAG,CAAA,EAAG,CAAC,IAAA,EAAM,GAAG,CAAC;AAC/E,CAAA;AAMO,SAAS,aAAA,CAAc,MAAA,EAIA;AAC5B,EAAA,MAAM,IAAA,EAAM,iBAAA,CAAkB,IAAA;AAAA,IAC5B,CAAC,CAAA,EAAA,GACC,CAAA,CAAE,KAAA,IAAS,MAAA,CAAO,KAAA,GAClB,CAAA,CAAE,gBAAA,IAAoB,MAAA,CAAO,gBAAA,GAC7B,CAAA,CAAE,UAAA,IAAc,MAAA,CAAO;AAAA,EAC3B,CAAA;AACA,EAAA,OAAO,IAAA,IAAQ,KAAA,EAAA,EAAY,KAAA,EAAA,EAAY,GAAA,CAAI,SAAA;AAC7C;AFg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gqMAAC","file":"/home/runner/work/ocs-calculators/ocs-calculators/dist/index.cjs","sourcesContent":[null,"import { G0 } from '../types';\n\n/**\n * 接触线线材参数预设。\n *\n * ⚠️ 全部为标称参考值，实际取值以产品技术条件与设计文件为准。\n * ⚠️ 本站计算器的参数界面支持手工覆盖这些值 —— 那才是工程上正确的用法。\n *\n * 自重口径（2026-08-31 已确定）：\n * 线密度取标准「参考单位质量」表值，而非由标称截面推算。标准表分两列：\n *   型号｜标称截面｜计算截面｜参考单位质量\n *   CT 120｜120｜121｜1082 kg/km\n *   注：参考单位质量按密度 8.94 g/cm³ 计算\n * 即标准的 8.94 g/cm³ 是配「计算截面」（把尺寸公差计入后的截面）用的，\n * 不是配「标称截面」用的：121 × 8.94 × 1e-3 = 1.0817 ≈ 1.082 kg/m。\n * 因此 CTMH-120 自重 g = 1.082 × 9.81 = 10.61442 N/m，\n * 与站点 /calculator/tension/ 预设 rho=1.082、COPPER_TABLE.unitWeight=1082 一致。\n * 早期版本用标称截面 120 直接推算得 1.0728 kg/m，偏低约 0.85%，已废弃。\n *\n * 依据：TB/T 2810-2017（纯铜）、TB/T 2821-2017（铜银）规格尺寸表；\n * CTMH/CTAH 型号口径与 TB/T 2809-2017 的对应关系见 copper 模块 note 字段。\n */\n\nexport interface WireSpec {\n  /** 唯一标识 */\n  readonly id: WirePresetId;\n  /** 中文名 */\n  readonly name: string;\n  /** 英文名 */\n  readonly nameEn: string;\n  /** 标称截面积 A，mm² */\n  readonly crossSectionMM2: number;\n  /** 计算截面积，mm²（标准表列，自重按此值 × 8.94 g/cm³ 计） */\n  readonly calculatedSectionMM2: number;\n  /** 弹性模量 E，GPa（标称参考值） */\n  readonly elasticModulusGPa: number;\n  /** 线膨胀系数 α，1/℃（标称参考值） */\n  readonly expansionPerDegC: number;\n  /** 线密度，kg/m（标准参考单位质量） */\n  readonly linearMassKgPerM: number;\n}\n\n/** 参考密度，g/cm³（标准注：参考单位质量按此密度计） */\nexport const REFERENCE_DENSITY_G_PER_CM3 = 8.94;\n\n/** 线材预设 id */\nexport type WirePresetId = 'cthm120' | 'cthm150' | 'ctha120';\n\n/**\n * 标准「参考单位质量」表，kg/km。\n * 与 `src/copper/index.ts` 的 TB2809_WIRE_PARAMS.unitWeightKgPerKm 同源\n * （站点 /calculator/assets/calc-core.js 的 COPPER_TABLE）。\n */\nexport const STANDARD_UNIT_WEIGHT_KG_PER_KM: Readonly<Record<WirePresetId, number>> = {\n  cthm120: 1082,\n  cthm150: 1350,\n  ctha120: 1070,\n};\n\n/** 由标准参考单位质量换算线密度，kg/m */\nexport function unitWeightToKgPerM(kgPerKm: number): number {\n  return kgPerKm / 1000;\n}\n\n/**\n * 由截面积与密度反算线密度。\n *\n * ⚠️ 传入的必须是「计算截面」而非「标称截面」，否则结果偏低约 0.85%。\n * 120 mm² 标称对应计算截面 121 mm²；150 mm² 标称对应 151 mm²。\n *\n * @param crossSectionMM2 计算截面积，mm²\n * @param densityGPerCm3 密度，g/cm³\n * @returns 线密度，kg/m\n */\nexport function deriveLinearMassKgPerM(\n  crossSectionMM2: number,\n  densityGPerCm3: number = REFERENCE_DENSITY_G_PER_CM3,\n): number {\n  // A[mm²] × 1e-6 [m²/mm²] × ρ[g/cm³] × 1000 [kg/m³ per g/cm³]\n  return crossSectionMM2 * 1e-6 * densityGPerCm3 * 1000;\n}\n\n/** 铜及铜合金接触线的常用线膨胀系数，1/℃ */\nexport const COPPER_ALLOY_ALPHA_PER_DEG_C = 1.7e-5;\n\nexport const WIRE_PRESETS: readonly WireSpec[] = [\n  {\n    id: 'cthm120',\n    name: 'CTMH-120（铜镁 120）',\n    nameEn: 'CTMH-120 (CuMg 120 mm²)',\n    crossSectionMM2: 120,\n    calculatedSectionMM2: 121,\n    elasticModulusGPa: 120,\n    expansionPerDegC: COPPER_ALLOY_ALPHA_PER_DEG_C,\n    linearMassKgPerM: unitWeightToKgPerM(STANDARD_UNIT_WEIGHT_KG_PER_KM.cthm120),\n  },\n  {\n    id: 'cthm150',\n    name: 'CTMH-150（铜镁 150）',\n    nameEn: 'CTMH-150 (CuMg 150 mm²)',\n    crossSectionMM2: 150,\n    calculatedSectionMM2: 151,\n    elasticModulusGPa: 120,\n    expansionPerDegC: COPPER_ALLOY_ALPHA_PER_DEG_C,\n    linearMassKgPerM: unitWeightToKgPerM(STANDARD_UNIT_WEIGHT_KG_PER_KM.cthm150),\n  },\n  {\n    id: 'ctha120',\n    name: 'CTAH-120（铜银 120）',\n    nameEn: 'CTAH-120 (CuAg 120 mm²)',\n    crossSectionMM2: 120,\n    calculatedSectionMM2: 121,\n    elasticModulusGPa: 120,\n    expansionPerDegC: COPPER_ALLOY_ALPHA_PER_DEG_C,\n    linearMassKgPerM: unitWeightToKgPerM(STANDARD_UNIT_WEIGHT_KG_PER_KM.ctha120),\n  },\n];\n\n/** 按 id 取线材预设，找不到返回 undefined */\nexport function findWirePreset(id: string): WireSpec | undefined {\n  return WIRE_PRESETS.find((w) => w.id === id);\n}\n\n/**\n * 由线密度求单位自重荷载 g，N/m。\n * @param linearMassKgPerM 线密度，kg/m\n */\nexport function weightPerLengthNPerM(linearMassKgPerM: number): number {\n  return linearMassKgPerM * G0;\n}\n\n/**\n * 由线材预设直接取单位自重荷载 g，N/m。\n */\nexport function weightOfPresetNPerM(spec: WireSpec): number {\n  return weightPerLengthNPerM(spec.linearMassKgPerM);\n}\n","/**\n * TB/T 2809-2017 表5 持续载流量参考值（A）。\n *\n * 来源：itswe.com 标准规范库，据 TB/T 2809-2017 无水印全文扫描件逐格复核。\n *\n * 查表语义：\n *   - 返回数值：该项载流量\n *   - 返回 null：该 (材质， 截面) 规格存在，但该工况按标准原文注\"不需要考核\"\n *     （如纯铜接触线不考核 150℃ 工况）\n *   - 返回 undefined：该材质无此截面规格（如铜铬锆无 120 mm²）\n *\n * ⚠️ 表中为室内（无风无日照试验条件）值与室外值；工程取值请以标准原文与\n * 产品技术条件为准。高海拔、隧道内等场景须另行叠加散热修正。\n */\n\nexport type ContactWireTypeCode =\n  | 'CT'\n  | 'CTA'\n  | 'CTS'\n  | 'CTSM'\n  | 'CTSH'\n  | 'CTM'\n  | 'CTMM'\n  | 'CTMH'\n  | 'CTCZ';\n\n/** 载流量考核工况 */\nexport type AmpacityCondition = 'indoor-95' | 'outdoor-95' | 'indoor-150' | 'outdoor-150';\n\nexport type CrossSectionMM2 = 120 | 150;\n\n/** 按截面索引的载流量对，[120 mm², 150 mm²] */\ntype SectionPair = readonly [number | null, number | null];\n\nexport interface AmpacityEntry {\n  readonly type: ContactWireTypeCode;\n  readonly materialZh: string;\n  /** 标称截面，mm² */\n  readonly crossSectionMM2: CrossSectionMM2;\n  readonly condition: AmpacityCondition;\n  /** 持续载流量，A。null 表示该项不需要考核 */\n  readonly ampacityA: number | null;\n}\n\nconst M = (\n  type: ContactWireTypeCode,\n  materialZh: string,\n  sections: readonly CrossSectionMM2[],\n  indoor95: SectionPair,\n  outdoor95: SectionPair,\n  indoor150: SectionPair,\n  outdoor150: SectionPair,\n): AmpacityEntry[] => {\n  const conditions: ReadonlyArray<readonly [AmpacityCondition, SectionPair]> = [\n    ['indoor-95', indoor95],\n    ['outdoor-95', outdoor95],\n    ['indoor-150', indoor150],\n    ['outdoor-150', outdoor150],\n  ];\n  const out: AmpacityEntry[] = [];\n  for (const section of sections) {\n    for (const [condition, pair] of conditions) {\n      const value = section === 120 ? pair[0] : pair[1];\n      out.push({\n        type,\n        materialZh,\n        crossSectionMM2: section,\n        condition,\n        ampacityA: value ?? null,\n      });\n    }\n  }\n  return out;\n};\n\nexport const TB2809_AMPACITY_A: readonly AmpacityEntry[] = [\n  ...M('CT', '铜', [120, 150], [360, 425], [495, 570], [null, null], [null, null]),\n  ...M('CTA', '铜银', [120, 150], [360, 425], [495, 570], [515, 620], [680, 785]),\n  ...M('CTS', '铜锡', [120, 150], [360, 425], [490, 565], [515, 620], [680, 790]),\n  ...M('CTSM', '铜锡', [120, 150], [330, 400], [455, 525], [490, 560], [630, 730]),\n  ...M('CTSH', '铜锡', [120, 150], [310, 360], [420, 480], [450, 520], [580, 670]),\n  ...M('CTM', '铜镁', [120, 150], [330, 400], [455, 525], [490, 560], [630, 730]),\n  ...M('CTMM', '铜镁', [120, 150], [310, 360], [420, 480], [450, 520], [580, 670]),\n  ...M('CTMH', '铜镁', [120, 150], [300, 340], [410, 460], [430, 500], [560, 650]),\n  ...M('CTCZ', '铜铬锆', [150], [null, 395], [null, 505], [null, 580], [null, 710]),\n];\n\n/**\n * 查表。\n * @returns 载流量 A；该规格存在但不考核时为 null；该材质无此截面时为 undefined\n */\nexport function findAmpacityA(params: {\n  type: ContactWireTypeCode;\n  crossSectionMM2: CrossSectionMM2;\n  condition: AmpacityCondition;\n}): number | null | undefined {\n  const row = TB2809_AMPACITY_A.find(\n    (e) =>\n      e.type === params.type &&\n      e.crossSectionMM2 === params.crossSectionMM2 &&\n      e.condition === params.condition,\n  );\n  return row === undefined ? undefined : row.ampacityA;\n}\n"]}
+{"version":3,"sources":["/home/runner/work/ocs-calculators/ocs-calculators/dist/index.cjs","../src/data/wire-specs.ts","../src/data/tb2809-ampacity.ts"],"names":[],"mappings":"AAAA;AACE;AACA;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACA;AACA;AACA;AACF,wDAA6B;AAC7B;AACE;AACA;AACF,wDAA6B;AAC7B;AACA;AC5FO,IAAM,4BAAA,EAA8B,IAAA;AAUpC,IAAM,+BAAA,EAAyE;AAAA,EACpF,OAAA,EAAS,IAAA;AAAA,EACT,OAAA,EAAS,IAAA;AAAA,EACT,OAAA,EAAS;AACX,CAAA;AAGO,SAAS,kBAAA,CAAmB,OAAA,EAAyB;AAC1D,EAAA,OAAO,QAAA,EAAU,GAAA;AACnB;AAYO,SAAS,sBAAA,CACd,eAAA,EACA,eAAA,EAAyB,2BAAA,EACjB;AAER,EAAA,OAAO,gBAAA,EAAkB,KAAA,EAAO,eAAA,EAAiB,GAAA;AACnD;AAGO,IAAM,6BAAA,EAA+B,KAAA;AAErC,IAAM,aAAA,EAAoC;AAAA,EAC/C;AAAA,IACE,EAAA,EAAI,SAAA;AAAA,IACJ,IAAA,EAAM,sCAAA;AAAA,IACN,MAAA,EAAQ,4BAAA;AAAA,IACR,eAAA,EAAiB,GAAA;AAAA,IACjB,oBAAA,EAAsB,GAAA;AAAA,IACtB,iBAAA,EAAmB,GAAA;AAAA,IACnB,gBAAA,EAAkB,4BAAA;AAAA,IAClB,gBAAA,EAAkB,kBAAA,CAAmB,8BAAA,CAA+B,OAAO;AAAA,EAC7E,CAAA;AAAA,EACA;AAAA,IACE,EAAA,EAAI,SAAA;AAAA,IACJ,IAAA,EAAM,sCAAA;AAAA,IACN,MAAA,EAAQ,4BAAA;AAAA,IACR,eAAA,EAAiB,GAAA;AAAA,IACjB,oBAAA,EAAsB,GAAA;AAAA,IACtB,iBAAA,EAAmB,GAAA;AAAA,IACnB,gBAAA,EAAkB,4BAAA;AAAA,IAClB,gBAAA,EAAkB,kBAAA,CAAmB,8BAAA,CAA+B,OAAO;AAAA,EAC7E,CAAA;AAAA,EACA;AAAA,IACE,EAAA,EAAI,SAAA;AAAA,IACJ,IAAA,EAAM,sCAAA;AAAA,IACN,MAAA,EAAQ,4BAAA;AAAA,IACR,eAAA,EAAiB,GAAA;AAAA,IACjB,oBAAA,EAAsB,GAAA;AAAA,IACtB,iBAAA,EAAmB,GAAA;AAAA,IACnB,gBAAA,EAAkB,4BAAA;AAAA,IAClB,gBAAA,EAAkB,kBAAA,CAAmB,8BAAA,CAA+B,OAAO;AAAA,EAC7E;AACF,CAAA;AAGO,SAAS,cAAA,CAAe,EAAA,EAAkC;AAC/D,EAAA,OAAO,YAAA,CAAa,IAAA,CAAK,CAAC,CAAA,EAAA,GAAM,CAAA,CAAE,GAAA,IAAO,EAAE,CAAA;AAC7C;AAMO,SAAS,oBAAA,CAAqB,gBAAA,EAAkC;AACrE,EAAA,OAAO,iBAAA,EAAmB,oBAAA;AAC5B;AAKO,SAAS,mBAAA,CAAoB,IAAA,EAAwB;AAC1D,EAAA,OAAO,oBAAA,CAAqB,IAAA,CAAK,gBAAgB,CAAA;AACnD;ADsDA;AACA;AEnJA,IAAM,EAAA,EAAI,CACR,IAAA,EACA,UAAA,EACA,QAAA,EACA,QAAA,EACA,SAAA,EACA,SAAA,EACA,UAAA,EAAA,GACoB;AACpB,EAAA,MAAM,WAAA,EAAuE;AAAA,IAC3E,CAAC,WAAA,EAAa,QAAQ,CAAA;AAAA,IACtB,CAAC,YAAA,EAAc,SAAS,CAAA;AAAA,IACxB,CAAC,YAAA,EAAc,SAAS,CAAA;AAAA,IACxB,CAAC,aAAA,EAAe,UAAU;AAAA,EAC5B,CAAA;AACA,EAAA,MAAM,IAAA,EAAuB,CAAC,CAAA;AAC9B,EAAA,IAAA,CAAA,MAAW,QAAA,GAAW,QAAA,EAAU;AAC9B,IAAA,IAAA,CAAA,MAAW,CAAC,SAAA,EAAW,IAAI,EAAA,GAAK,UAAA,EAAY;AAC1C,MAAA,MAAM,MAAA,EAAQ,QAAA,IAAY,IAAA,EAAM,IAAA,CAAK,CAAC,EAAA,EAAI,IAAA,CAAK,CAAC,CAAA;AAChD,MAAA,GAAA,CAAI,IAAA,CAAK;AAAA,QACP,IAAA;AAAA,QACA,UAAA;AAAA,QACA,eAAA,EAAiB,OAAA;AAAA,QACjB,SAAA;AAAA,QACA,SAAA,mBAAW,KAAA,UAAS;AAAA,MACtB,CAAC,CAAA;AAAA,IACH;AAAA,EACF;AACA,EAAA,OAAO,GAAA;AACT,CAAA;AAEO,IAAM,kBAAA,EAA8C;AAAA,EACzD,GAAG,CAAA,CAAE,IAAA,EAAM,QAAA,EAAK,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,IAAA,EAAM,IAAI,CAAA,EAAG,CAAC,IAAA,EAAM,IAAI,CAAC,CAAA;AAAA,EAC9E,GAAG,CAAA,CAAE,KAAA,EAAO,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC5E,GAAG,CAAA,CAAE,KAAA,EAAO,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC5E,GAAG,CAAA,CAAE,MAAA,EAAQ,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC7E,GAAG,CAAA,CAAE,MAAA,EAAQ,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC7E,GAAG,CAAA,CAAE,KAAA,EAAO,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC5E,GAAG,CAAA,CAAE,MAAA,EAAQ,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC7E,GAAG,CAAA,CAAE,MAAA,EAAQ,cAAA,EAAM,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAA,EAAG,CAAC,GAAA,EAAK,GAAG,CAAC,CAAA;AAAA,EAC7E,GAAG,CAAA,CAAE,MAAA,EAAQ,oBAAA,EAAO,CAAC,GAAG,CAAA,EAAG,CAAC,IAAA,EAAM,GAAG,CAAA,EAAG,CAAC,IAAA,EAAM,GAAG,CAAA,EAAG,CAAC,IAAA,EAAM,GAAG,CAAA,EAAG,CAAC,IAAA,EAAM,GAAG,CAAC;AAC/E,CAAA;AAMO,SAAS,aAAA,CAAc,MAAA,EAIA;AAC5B,EAAA,MAAM,IAAA,EAAM,iBAAA,CAAkB,IAAA;AAAA,IAC5B,CAAC,CAAA,EAAA,GACC,CAAA,CAAE,KAAA,IAAS,MAAA,CAAO,KAAA,GAClB,CAAA,CAAE,gBAAA,IAAoB,MAAA,CAAO,gBAAA,GAC7B,CAAA,CAAE,UAAA,IAAc,MAAA,CAAO;AAAA,EAC3B,CAAA;AACA,EAAA,OAAO,IAAA,IAAQ,KAAA,EAAA,EAAY,KAAA,EAAA,EAAY,GAAA,CAAI,SAAA;AAC7C;AFgIA;AACE;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACA;AACF,gqMAAC","file":"/home/runner/work/ocs-calculators/ocs-calculators/dist/index.cjs","sourcesContent":[null,"import { G0 } from '../types';\n\n/**\n * 接触线线材参数预设。\n *\n * ⚠️ 全部为标称参考值，实际取值以产品技术条件与设计文件为准。\n * ⚠️ 本站计算器的参数界面支持手工覆盖这些值 —— 那才是工程上正确的用法。\n *\n * 自重口径（2026-08-31 已确定）：\n * 线密度取标准「参考单位质量」表值，而非由标称截面推算。标准表分两列：\n *   型号｜标称截面｜计算截面｜参考单位质量\n *   CT 120｜120｜121｜1082 kg/km\n *   注：参考单位质量按密度 8.94 g/cm³ 计算\n * 即标准的 8.94 g/cm³ 是配「计算截面」（把尺寸公差计入后的截面）用的，\n * 不是配「标称截面」用的：121 × 8.94 × 1e-3 = 1.0817 ≈ 1.082 kg/m。\n * 因此 CTMH-120 自重 g = 1.082 × 9.81 = 10.61442 N/m，\n * 与站点 /calculator/tension/ 预设 rho=1.082、COPPER_TABLE.unitWeight=1082 一致。\n * 早期版本用标称截面 120 直接推算得 1.0728 kg/m，偏低约 0.85%，已废弃。\n *\n * 依据：TB/T 2810-2017（纯铜）、TB/T 2821-2017（铜银）规格尺寸表；\n * CTMH/CTAH 型号口径与 TB/T 2809-2017 的对应关系见 copper 模块 note 字段。\n */\n\nexport interface WireSpec {\n  /** 唯一标识 */\n  readonly id: WirePresetId;\n  /** 中文名 */\n  readonly name: string;\n  /** 英文名 */\n  readonly nameEn: string;\n  /** 标称截面积 A，mm² */\n  readonly crossSectionMM2: number;\n  /** 计算截面积，mm²（标准表列，自重按此值 × 8.94 g/cm³ 计） */\n  readonly calculatedSectionMM2: number;\n  /** 弹性模量 E，GPa（标称参考值） */\n  readonly elasticModulusGPa: number;\n  /** 线膨胀系数 α，1/℃（标称参考值） */\n  readonly expansionPerDegC: number;\n  /** 线密度，kg/m（标准参考单位质量） */\n  readonly linearMassKgPerM: number;\n}\n\n/** 参考密度，g/cm³（标准注：参考单位质量按此密度计） */\nexport const REFERENCE_DENSITY_G_PER_CM3 = 8.94;\n\n/** 线材预设 id */\nexport type WirePresetId = 'cthm120' | 'cthm150' | 'ctha120';\n\n/**\n * 标准「参考单位质量」表，kg/km。\n * 与 `src/copper/index.ts` 的 TB2809_WIRE_PARAMS.unitWeightKgPerKm 同源\n * （站点 /calculator/assets/calc-core.js 的 COPPER_TABLE）。\n */\nexport const STANDARD_UNIT_WEIGHT_KG_PER_KM: Readonly<Record<WirePresetId, number>> = {\n  cthm120: 1082,\n  cthm150: 1350,\n  ctha120: 1070,\n};\n\n/** 由标准参考单位质量换算线密度，kg/m */\nexport function unitWeightToKgPerM(kgPerKm: number): number {\n  return kgPerKm / 1000;\n}\n\n/**\n * 由截面积与密度反算线密度。\n *\n * ⚠️ 传入的必须是「计算截面」而非「标称截面」，否则结果偏低约 0.85%。\n * 120 mm² 标称对应计算截面 121 mm²；150 mm² 标称对应 151 mm²。\n *\n * @param crossSectionMM2 计算截面积，mm²\n * @param densityGPerCm3 密度，g/cm³\n * @returns 线密度，kg/m\n */\nexport function deriveLinearMassKgPerM(\n  crossSectionMM2: number,\n  densityGPerCm3: number = REFERENCE_DENSITY_G_PER_CM3,\n): number {\n  // A[mm²] × 1e-6 [m²/mm²] × ρ[g/cm³] × 1000 [kg/m³ per g/cm³]\n  return crossSectionMM2 * 1e-6 * densityGPerCm3 * 1000;\n}\n\n/** 铜及铜合金接触线的常用线膨胀系数，1/℃ */\nexport const COPPER_ALLOY_ALPHA_PER_DEG_C = 1.7e-5;\n\nexport const WIRE_PRESETS: readonly WireSpec[] = [\n  {\n    id: 'cthm120',\n    name: 'CTMH-120（铜镁 120）',\n    nameEn: 'CTMH-120 (CuMg 120 mm²)',\n    crossSectionMM2: 120,\n    calculatedSectionMM2: 121,\n    elasticModulusGPa: 120,\n    expansionPerDegC: COPPER_ALLOY_ALPHA_PER_DEG_C,\n    linearMassKgPerM: unitWeightToKgPerM(STANDARD_UNIT_WEIGHT_KG_PER_KM.cthm120),\n  },\n  {\n    id: 'cthm150',\n    name: 'CTMH-150（铜镁 150）',\n    nameEn: 'CTMH-150 (CuMg 150 mm²)',\n    crossSectionMM2: 150,\n    calculatedSectionMM2: 151,\n    elasticModulusGPa: 120,\n    expansionPerDegC: COPPER_ALLOY_ALPHA_PER_DEG_C,\n    linearMassKgPerM: unitWeightToKgPerM(STANDARD_UNIT_WEIGHT_KG_PER_KM.cthm150),\n  },\n  {\n    id: 'ctha120',\n    name: 'CTAH-120（铜银 120）',\n    nameEn: 'CTAH-120 (CuAg 120 mm²)',\n    crossSectionMM2: 120,\n    calculatedSectionMM2: 121,\n    elasticModulusGPa: 120,\n    expansionPerDegC: COPPER_ALLOY_ALPHA_PER_DEG_C,\n    linearMassKgPerM: unitWeightToKgPerM(STANDARD_UNIT_WEIGHT_KG_PER_KM.ctha120),\n  },\n];\n\n/** 按 id 取线材预设，找不到返回 undefined */\nexport function findWirePreset(id: string): WireSpec | undefined {\n  return WIRE_PRESETS.find((w) => w.id === id);\n}\n\n/**\n * 由线密度求单位自重荷载 g，N/m。\n * @param linearMassKgPerM 线密度，kg/m\n */\nexport function weightPerLengthNPerM(linearMassKgPerM: number): number {\n  return linearMassKgPerM * G0;\n}\n\n/**\n * 由线材预设直接取单位自重荷载 g，N/m。\n */\nexport function weightOfPresetNPerM(spec: WireSpec): number {\n  return weightPerLengthNPerM(spec.linearMassKgPerM);\n}\n","/**\n * TB/T 2809-2017 表5 持续载流量参考值（A）。\n *\n * 来源：itswe.com 标准规范库，据 TB/T 2809-2017 无水印全文扫描件逐格复核。\n *\n * 查表语义：\n *   - 返回数值：该项载流量\n *   - 返回 null：该 (材质， 截面) 规格存在，但该工况按标准原文注\"不需要考核\"\n *     （如纯铜接触线不考核 150℃ 工况）\n *   - 返回 undefined：该材质无此截面规格（如铜铬锆无 120 mm²）\n *\n * ⚠️ 表中为室内（无风无日照试验条件）值与室外值；工程取值请以标准原文与\n * 产品技术条件为准。高海拔、隧道内等场景须另行叠加散热修正。\n */\n\nexport type ContactWireTypeCode =\n  | 'CT'\n  | 'CTA'\n  | 'CTS'\n  | 'CTSM'\n  | 'CTSH'\n  | 'CTM'\n  | 'CTMM'\n  | 'CTMH'\n  | 'CTCZ';\n\n/** 载流量考核工况 */\nexport type AmpacityCondition = 'indoor-95' | 'outdoor-95' | 'indoor-150' | 'outdoor-150';\n\nexport type CrossSectionMM2 = 120 | 150;\n\n/** 按截面索引的载流量对，[120 mm², 150 mm²] */\ntype SectionPair = readonly [number | null, number | null];\n\nexport interface AmpacityEntry {\n  readonly type: ContactWireTypeCode;\n  readonly materialZh: string;\n  /** 标称截面，mm² */\n  readonly crossSectionMM2: CrossSectionMM2;\n  readonly condition: AmpacityCondition;\n  /** 持续载流量，A。null 表示该项不需要考核 */\n  readonly ampacityA: number | null;\n}\n\nconst M = (\n  type: ContactWireTypeCode,\n  materialZh: string,\n  sections: readonly CrossSectionMM2[],\n  indoor95: SectionPair,\n  outdoor95: SectionPair,\n  indoor150: SectionPair,\n  outdoor150: SectionPair,\n): AmpacityEntry[] => {\n  const conditions: ReadonlyArray<readonly [AmpacityCondition, SectionPair]> = [\n    ['indoor-95', indoor95],\n    ['outdoor-95', outdoor95],\n    ['indoor-150', indoor150],\n    ['outdoor-150', outdoor150],\n  ];\n  const out: AmpacityEntry[] = [];\n  for (const section of sections) {\n    for (const [condition, pair] of conditions) {\n      const value = section === 120 ? pair[0] : pair[1];\n      out.push({\n        type,\n        materialZh,\n        crossSectionMM2: section,\n        condition,\n        ampacityA: value ?? null,\n      });\n    }\n  }\n  return out;\n};\n\nexport const TB2809_AMPACITY_A: readonly AmpacityEntry[] = [\n  ...M('CT', '铜', [120, 150], [360, 425], [495, 570], [null, null], [null, null]),\n  ...M('CTA', '铜银', [120, 150], [360, 425], [495, 570], [515, 620], [680, 785]),\n  ...M('CTS', '铜锡', [120, 150], [360, 425], [490, 565], [515, 620], [680, 790]),\n  ...M('CTSM', '铜锡', [120, 150], [330, 400], [455, 525], [490, 560], [630, 730]),\n  ...M('CTSH', '铜锡', [120, 150], [310, 360], [420, 480], [450, 520], [580, 670]),\n  ...M('CTM', '铜镁', [120, 150], [330, 400], [455, 525], [490, 560], [630, 730]),\n  ...M('CTMM', '铜镁', [120, 150], [310, 360], [420, 480], [450, 520], [580, 670]),\n  ...M('CTMH', '铜镁', [120, 150], [300, 340], [410, 460], [430, 500], [560, 650]),\n  ...M('CTCZ', '铜铬锆', [150], [null, 395], [null, 505], [null, 580], [null, 710]),\n];\n\n/**\n * 查表。\n * @returns 载流量 A；该规格存在但不考核时为 null；该材质无此截面时为 undefined\n */\nexport function findAmpacityA(params: {\n  type: ContactWireTypeCode;\n  crossSectionMM2: CrossSectionMM2;\n  condition: AmpacityCondition;\n}): number | null | undefined {\n  const row = TB2809_AMPACITY_A.find(\n    (e) =>\n      e.type === params.type &&\n      e.crossSectionMM2 === params.crossSectionMM2 &&\n      e.condition === params.condition,\n  );\n  return row === undefined ? undefined : row.ampacityA;\n}\n"]}

package/dist/index.js

@@ -20,12 +20,6 @@ import {
   waveSpeedCheck,
   wavespeedMeta
 } from "./chunk-VAHQDIMW.js";
-import {
-  DEFAULT_REPLACEMENT_THRESHOLD_PERCENT,
-  sectionFromDiameterMM2,
-  wearMeta,
-  wearRatio
-} from "./chunk-LDSV3U4M.js";
 import {
   AIR_DENSITY_KG_PER_M3,
   windClearanceCheck,
@@ -33,6 +27,12 @@ import {
   windLoadNPerM,
   windMeta
 } from "./chunk-RVG3LEZQ.js";
+import {
+  DEFAULT_REPLACEMENT_THRESHOLD_PERCENT,
+  sectionFromDiameterMM2,
+  wearMeta,
+  wearRatio
+} from "./chunk-LDSV3U4M.js";
 import {
   DEFAULT_PANTOGRAPH_HEIGHT_M,
   STANDARD_GAUGE_M,
@@ -41,13 +41,6 @@ import {
   curveStaggerMeta,
   versineM
 } from "./chunk-IFVYGNT3.js";
-import {
-  dropperLengths,
-  dropperMeta,
-  dropperPositionsM,
-  maxParabolaSagM,
-  parabolaSagM
-} from "./chunk-UO2PHBC3.js";
 import {
   REF_TARGET_COEFF,
   REF_TARGET_OFFSET_N,
@@ -63,18 +56,25 @@ import {
   icingCheck,
   icingMeta
 } from "./chunk-GN6QNOUL.js";
+import {
+  dropperLengths,
+  dropperMeta,
+  dropperPositionsM,
+  maxParabolaSagM,
+  parabolaSagM
+} from "./chunk-UO2PHBC3.js";
 import {
   STEEL_POLE_SERIES_KNM,
   TEST_MOMENT_FACTOR,
   poleCapacityCheck,
   poleCapacityMeta
-} from "./chunk-VXVTT6WS.js";
+} from "./chunk-2YFKWFBJ.js";
 import {
   maxSpanFromSagM,
   sagMM,
   sagMeta,
   tensionFromSagKN
-} from "./chunk-C2XU3XKP.js";
+} from "./chunk-Q7UD52SC.js";
 import {
   steadyArmAngleDeg,
   steadyArmCheck,
@@ -102,15 +102,15 @@ import {
   anchorLengthCheck,
   anchorLengthMeta
 } from "./chunk-75EGROQB.js";
-import {
-  bValue,
-  bvalueMeta
-} from "./chunk-3GREMF76.js";
 import {
   ASSEMBLY_TOLERANCE_MM,
   cantileverCut,
   cantileverMeta
 } from "./chunk-HZWNKKIB.js";
+import {
+  bValue,
+  bvalueMeta
+} from "./chunk-3GREMF76.js";
 import {
   TB2809_WIRE_PARAMS,
   copperMeta,
@@ -127,7 +127,7 @@ import {
   USCD_BANDS,
   creepageCheck,
   creepageMeta
-} from "./chunk-CLVLOLUJ.js";
+} from "./chunk-3LUPNS4U.js";
 import {
   crossSpanAnalyze,
   crossSpanMeta

package/dist/pole-capacity/index.cjs

@@ -3,11 +3,11 @@
 
 
 
-var _chunk4344WWAFcjs = require('../chunk-4344WWAF.cjs');
+var _chunkR4IVRYJAcjs = require('../chunk-R4IVRYJA.cjs');
 
 
 
 
 
-exports.STEEL_POLE_SERIES_KNM = _chunk4344WWAFcjs.STEEL_POLE_SERIES_KNM; exports.TEST_MOMENT_FACTOR = _chunk4344WWAFcjs.TEST_MOMENT_FACTOR; exports.poleCapacityCheck = _chunk4344WWAFcjs.poleCapacityCheck; exports.poleCapacityMeta = _chunk4344WWAFcjs.poleCapacityMeta;
+exports.STEEL_POLE_SERIES_KNM = _chunkR4IVRYJAcjs.STEEL_POLE_SERIES_KNM; exports.TEST_MOMENT_FACTOR = _chunkR4IVRYJAcjs.TEST_MOMENT_FACTOR; exports.poleCapacityCheck = _chunkR4IVRYJAcjs.poleCapacityCheck; exports.poleCapacityMeta = _chunkR4IVRYJAcjs.poleCapacityMeta;
 //# sourceMappingURL=index.cjs.map

package/dist/pole-capacity/index.js

@@ -3,7 +3,7 @@ import {
   TEST_MOMENT_FACTOR,
   poleCapacityCheck,
   poleCapacityMeta
-} from "../chunk-VXVTT6WS.js";
+} from "../chunk-2YFKWFBJ.js";
 export {
   STEEL_POLE_SERIES_KNM,
   TEST_MOMENT_FACTOR,

package/dist/sag/index.cjs

@@ -3,11 +3,11 @@
 
 
 
-var _chunkPYNVEHGRcjs = require('../chunk-PYNVEHGR.cjs');
+var _chunkCF663UNGcjs = require('../chunk-CF663UNG.cjs');
 
 
 
 
 
-exports.maxSpanFromSagM = _chunkPYNVEHGRcjs.maxSpanFromSagM; exports.sagMM = _chunkPYNVEHGRcjs.sagMM; exports.sagMeta = _chunkPYNVEHGRcjs.sagMeta; exports.tensionFromSagKN = _chunkPYNVEHGRcjs.tensionFromSagKN;
+exports.maxSpanFromSagM = _chunkCF663UNGcjs.maxSpanFromSagM; exports.sagMM = _chunkCF663UNGcjs.sagMM; exports.sagMeta = _chunkCF663UNGcjs.sagMeta; exports.tensionFromSagKN = _chunkCF663UNGcjs.tensionFromSagKN;
 //# sourceMappingURL=index.cjs.map

package/dist/sag/index.js

@@ -3,7 +3,7 @@ import {
   sagMM,
   sagMeta,
   tensionFromSagKN
-} from "../chunk-C2XU3XKP.js";
+} from "../chunk-Q7UD52SC.js";
 export {
   maxSpanFromSagM,
   sagMM,

package/package.json

@@ -1,6 +1,6 @@
 {
   "name": "ocs-calculators",
-  "version": "0.2.0",
+  "version": "0.2.2",
   "description": "铁路接触网（OCS）工程计算工具集 —— 张力、弛度、吊弦、风偏移等计算，零依赖纯函数实现 / Railway overhead contact system (OCS) engineering calculators as zero-dependency pure functions",
   "keywords": [
     "catenary",
@@ -88,42 +88,42 @@
       "require": "./dist/wear/index.cjs"
     },
     "./package.json": "./package.json",
-    "steady-arm": {
+    "./steady-arm": {
       "types": "./dist/steady-arm/index.d.ts",
       "import": "./dist/steady-arm/index.js",
       "require": "./dist/steady-arm/index.cjs"
     },
-    "cross-span": {
+    "./cross-span": {
       "types": "./dist/cross-span/index.d.ts",
       "import": "./dist/cross-span/index.js",
       "require": "./dist/cross-span/index.cjs"
     },
-    "bvalue": {
+    "./bvalue": {
       "types": "./dist/bvalue/index.d.ts",
       "import": "./dist/bvalue/index.js",
       "require": "./dist/bvalue/index.cjs"
     },
-    "sag": {
+    "./sag": {
       "types": "./dist/sag/index.d.ts",
       "import": "./dist/sag/index.js",
       "require": "./dist/sag/index.cjs"
     },
-    "anchor-length": {
+    "./anchor-length": {
       "types": "./dist/anchor-length/index.d.ts",
       "import": "./dist/anchor-length/index.js",
       "require": "./dist/anchor-length/index.cjs"
     },
-    "creepage": {
+    "./creepage": {
       "types": "./dist/creepage/index.d.ts",
       "import": "./dist/creepage/index.js",
       "require": "./dist/creepage/index.cjs"
     },
-    "pole-capacity": {
+    "./pole-capacity": {
       "types": "./dist/pole-capacity/index.d.ts",
       "import": "./dist/pole-capacity/index.js",
       "require": "./dist/pole-capacity/index.cjs"
     },
-    "cantilever": {
+    "./cantilever": {
       "types": "./dist/cantilever/index.d.ts",
       "import": "./dist/cantilever/index.js",
       "require": "./dist/cantilever/index.cjs"
@@ -161,4 +161,4 @@
     "url": "https://github.com/showhoo/ocs-calculators/issues"
   },
   "author": "思维接触网百科"
-}
+}

package/dist/chunk-4344WWAF.cjs.map

@@ -1 +0,0 @@
-{"version":3,"sources":["/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-4344WWAF.cjs","../src/pole-capacity/meta.ts","../src/pole-capacity/index.ts"],"names":[],"mappings":"AAAA;ACEO,IAAM,iBAAA,EAAmC;AAAA,EAC9C,IAAA,EAAM,kDAAA;AAAA,EACN,MAAA,EAAQ,+BAAA;AAAA,EACR,OAAA,EAAS,8OAAA;AAAA,EACT,OAAA,EAAS;AAAA,IACP,uGAAA;AAAA,IACA,2EAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,UAAA,EAAY;AAAA,IACV,uIAAA;AAAA,IACA,0LAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,KAAA,EAAO,CAAC,2BAAA,EAAc,2BAAA,EAAc,+BAAA,EAAkB,gCAAY,CAAA;AAAA,EAClE,UAAA,EAAY,sKAAA;AAAA,EACZ,MAAA,EAAQ;AACV,CAAA;ADAA;AACA;AEjBO,IAAM,sBAAA,EAAwB,CAAC,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,GAAA,EAAK,IAAA,EAAM,IAAA,EAAM,IAAI,CAAA;AAGhH,IAAM,mBAAA,EAAqB,GAAA;AAwC3B,SAAS,iBAAA,CAAkB,KAAA,EAA8C;AAC9E,EAAA,MAAM,EAAE,OAAA,EAAS,oBAAA,EAAsB,kBAAA,EAAoB,SAAA,EAAW,KAAA,EAAO,gBAAA,EAAkB,cAAA,EAAgB,UAAA,EAAY,WAAA,EAAa,cAAc,EAAA,EAAI,KAAA;AAC1J,EAAA,GAAA,CAAI,CAAA,CAAE,qBAAA,GAAwB,CAAA,EAAA,GAAM,CAAA,CAAE,mBAAA,GAAsB,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,sCAAQ,CAAA;AAC7F,EAAA,MAAM,EAAA,EAAI,qBAAA,EAAuB,kBAAA;AACjC,EAAA,MAAM,EAAA,EAAI,UAAA,EAAY,GAAA;AACtB,EAAA,MAAM,GAAA,EAAM,EAAA,EAAI,EAAA,EAAI,EAAA,EAAK,KAAA;AACzB,EAAA,IAAI,EAAA;AACJ,EAAA,GAAA,CAAI,QAAA,IAAY,OAAA,EAAS;AACvB,IAAA,GAAA,CAAI,CAAA,CAAE,KAAA,CAAM,aAAA,GAAgB,KAAA,CAAM,aAAA,EAAe,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,kDAAU,CAAA;AACpF,IAAA,MAAM,GAAA,EAAM,EAAA,EAAI,MAAA,EAAS,KAAA,CAAM,YAAA;AAC/B,IAAA,GAAA,EAAK,IAAA,CAAK,GAAA,CAAI,GAAA,EAAK,EAAE,CAAA;AAAA,EACvB,EAAA,KAAO;AACL,IAAA,GAAA,EAAK,EAAA;AAAA,EACP;AACA,EAAA,MAAM,GAAA,EAAK,GAAA,EAAK,gBAAA;AAChB,EAAA,MAAM,GAAA,EAAM,eAAA,EAAiB,WAAA,EAAa,IAAA,CAAK,GAAA,CAAI,WAAA,EAAa,CAAC,EAAA,EAAI,EAAA,EAAK,GAAA;AAC1E,EAAA,MAAM,GAAA,EAAA,kBAAO,aAAA,UAAiB,GAAA,EAAA,EAAK,iBAAA,EAAoB,GAAA;AACvD,EAAA,MAAM,EAAA,EAAI,GAAA,EAAK,GAAA,EAAK,EAAA;AACpB,EAAA,MAAM,QAAA,EAAU,EAAA,EAAI,kBAAA;AACpB,EAAA,MAAM,KAAA,mBAAO,qBAAA,CAAsB,IAAA,CAAK,CAAC,CAAA,EAAA,GAAM,EAAA,GAAK,OAAO,CAAA,UAAK,MAAA;AAChE,EAAA,OAAO;AAAA,IACL,gBAAA,EAAkB,GAAA,EAAK,GAAA;AAAA,IACvB,aAAA,EAAe,CAAA;AAAA,IACf,cAAA,EAAgB,OAAA;AAAA,IAChB,SAAA,EAAW,KAAA,EAAO,IAAA,EAAM,KAAA,EAAO;AAAA,EACjC,CAAA;AACF;AFtBA;AACA;AACE;AACA;AACA;AACA;AACF,mMAAC","file":"/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-4344WWAF.cjs","sourcesContent":[null,"import type { CalculatorMeta } from '../types';\n\nexport const poleCapacityMeta: CalculatorMeta = {\n  name: '支柱容量选型校核',\n  nameEn: 'Mast Capacity Selection Check',\n  summary: '容量比较法：悬挂水平力与支柱风载合成工作弯矩，对照 GB/T 25020.1 钢支柱检验弯矩系列选型。',\n  formula: [\n    '直线之字力 F_z = 4(T_j+T_c)·a/l；曲线力 F_q = (T_j+T_c)·l/R',\n    '工作弯矩 M = F_h·h_e + P·b·h²/2 + F_wl·h_e',\n    '承载力检验弯矩 = 1.5 × 标称容量（25020.1 表 A.2 表值规律）',\n  ],\n  references: [\n    '钢柱直接依据：GB/T 25020.1-2025 第 5.1.1 条 + 附录 A 检验弯矩系列',\n    '同口径混凝土柱条款：TB/T 2286-2020 第 5.9.2 条（荷载矢量组合不大于检验弯矩）',\n    '分项系数极限状态法（GB/T 32578-2016 6.3.3 表 15）为设计正式口径，不可混用',\n  ],\n  scope: ['张力：5~45 kN', '跨距：30~90 m', '风压：100~1500 Pa', '支柱高：5~20 m'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/pole-capacity/',\n};\n","export { poleCapacityMeta } from './meta';\n\n/** GB/T 25020.1-2025 格构式钢支柱标称容量系列（表 A.2），kN·m */\nexport const STEEL_POLE_SERIES_KNM = [150, 200, 250, 300, 350, 400, 450, 500, 550, 600, 650, 750, 900, 1050, 1200, 1500] as const;\n\n/** 承载力检验弯矩 = 1.5 × 标称容量（25020.1 表 A.2 表值规律） */\nexport const TEST_MOMENT_FACTOR = 1.5;\n\n/** 支柱容量校核输入。单位：kN、m、mm、Pa。 */\nexport interface PoleCapacityInput {\n  /** 区段类型 */\n  readonly section: 'line' | 'curve';\n  /** 接触线张力 T_j，kN */\n  readonly contactWireTensionKN: number;\n  /** 承力索张力 T_c，kN */\n  readonly messengerTensionKN: number;\n  /** 拉出值 a，mm */\n  readonly staggerMM: number;\n  /** 跨距 l，m */\n  readonly spanM: number;\n  /** 曲线半径 R，m（曲线区段） */\n  readonly curveRadiusM?: number;\n  /** 水平力合力作用高度 h_e，m */\n  readonly resultantHeightM: number;\n  /** 设计最大风压 P，Pa */\n  readonly windPressurePa: number;\n  /** 支柱迎风宽度 b，m */\n  readonly poleWidthM: number;\n  /** 支柱高度 h，m */\n  readonly poleHeightM: number;\n  /** 线索风载 F_wl，N */\n  readonly wireWindLoadN?: number;\n}\n\nexport interface PoleCapacityResult {\n  /** 悬挂水平力 F_h，N */\n  readonly horizontalForceN: number;\n  /** 工作弯矩 M，kN·m */\n  readonly workMomentKNM: number;\n  /** 折合标称容量（÷1.5），kN·m */\n  readonly nominalNeedKNM: number;\n  /** 选型结果 */\n  readonly selection: string | null;\n}\n\n/** 支柱容量选型（容量比较法，TB/T 2286 5.9.2 检验弯矩口径；钢柱 25020.1 5.1.1+附录A） */\nexport function poleCapacityCheck(input: PoleCapacityInput): PoleCapacityResult {\n  const { section, contactWireTensionKN, messengerTensionKN, staggerMM, spanM, resultantHeightM, windPressurePa, poleWidthM, poleHeightM, wireWindLoadN } = input;\n  if (!(contactWireTensionKN >= 0) || !(messengerTensionKN >= 0)) throw new RangeError('张力不能为负');\n  const T = contactWireTensionKN + messengerTensionKN;\n  const a = staggerMM / 1e3;\n  const Fz = (4 * T * a) / spanM; // kN\n  let Fh: number;\n  if (section === 'curve') {\n    if (!(input.curveRadiusM && input.curveRadiusM > 0)) throw new RangeError('曲线半径必须为正');\n    const Fq = (T * spanM) / input.curveRadiusM;\n    Fh = Math.abs(Fq - Fz);\n  } else {\n    Fh = Fz;\n  }\n  const M1 = Fh * resultantHeightM; // 悬挂水平力矩 kN·m\n  const M2 = (windPressurePa * poleWidthM * Math.pow(poleHeightM, 2) / 2) / 1e3; // 支柱风载矩\n  const M3 = ((wireWindLoadN ?? 0) * resultantHeightM) / 1e3;\n  const M = M1 + M2 + M3;\n  const nomNeed = M / TEST_MOMENT_FACTOR;\n  const pick = STEEL_POLE_SERIES_KNM.find((n) => n >= nomNeed) ?? null;\n  return {\n    horizontalForceN: Fh * 1e3,\n    workMomentKNM: M,\n    nominalNeedKNM: nomNeed,\n    selection: pick ? 'G' + pick : null,\n  };\n}\n"]}

package/dist/chunk-LBGUOTCJ.cjs.map

@@ -1 +0,0 @@
-{"version":3,"sources":["/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-LBGUOTCJ.cjs","../src/creepage/meta.ts","../src/creepage/index.ts"],"names":[],"mappings":"AAAA;ACEO,IAAM,aAAA,EAA+B;AAAA,EAC1C,IAAA,EAAM,oEAAA;AAAA,EACN,MAAA,EAAQ,mCAAA;AAAA,EACR,OAAA,EAAS,sMAAA;AAAA,EACT,OAAA,EAAS;AAAA,IACP,8JAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,UAAA,EAAY;AAAA,IACV,sFAAA;AAAA,IACA,uKAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,KAAA,EAAO,CAAC,2CAAA,EAAoB,sDAAmB,CAAA;AAAA,EAC/C,UAAA,EAAY,sKAAA;AAAA,EACZ,MAAA,EAAQ;AACV,CAAA;ADAA;AACA;AEhBO,IAAM,uBAAA,EAAyB,IAAA;AAE/B,IAAM,oBAAA,EAAsB,IAAA;AAG5B,IAAM,WAAA,EAAa;AAAA,EACxB,EAAE,KAAA,EAAO,cAAA,EAAM,GAAA,EAAK,EAAA,EAAI,GAAA,EAAK,GAAG,CAAA;AAAA,EAChC,EAAE,KAAA,EAAO,oBAAA,EAAO,GAAA,EAAK,EAAA,EAAI,GAAA,EAAK,GAAG,CAAA;AAAA,EACjC,EAAE,KAAA,EAAO,cAAA,EAAM,GAAA,EAAK,EAAA,EAAI,GAAA,EAAK,SAAS;AACxC,CAAA;AAGO,SAAS,aAAA,CAAc,KAAA,EAS5B;AACA,EAAA,MAAM,QAAA,EAAW,KAAA,CAAM,SAAA,IAAa,OAAA,EAAS,oBAAA,EAAsB,sBAAA;AACnE,EAAA,MAAM,GAAA,mBAAK,KAAA,CAAM,YAAA,UAAgB,IAAA;AACjC,EAAA,MAAM,UAAA,EAAY,UAAA,CAAW,GAAA,CAAI,CAAC,CAAA,EAAA,GAAA,CAAO;AAAA,IACvC,KAAA,EAAO,CAAA,CAAE,KAAA;AAAA,IACT,EAAA,EAAI,CAAA,CAAE,IAAA,IAAQ,SAAA,EAAW,IAAA,CAAK,KAAA,CAAM,CAAA,CAAE,IAAA,EAAM,EAAE,EAAA,EAAI,IAAA,CAAK,KAAA,CAAM,CAAA,CAAE,IAAA,EAAM,EAAE;AAAA,EACzE,CAAA,CAAE,CAAA;AACF,EAAA,OAAO,EAAE,OAAA,EAAS,MAAA,EAAQ,KAAA,CAAM,WAAA,GAAc,OAAA,EAAS,UAAU,CAAA;AACnE;AFIA;AACA;AACE;AACA;AACA;AACA;AACA;AACF,wNAAC","file":"/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-LBGUOTCJ.cjs","sourcesContent":[null,"import type { CalculatorMeta } from '../types';\n\nexport const creepageMeta: CalculatorMeta = {\n  name: '绝缘子爬电距离选型校核',\n  nameEn: 'Insulator Creepage Distance Check',\n  summary: '按 TB 10009-2016 第 5.3.2 条底线判定接触网绝缘最小爬电距离，附 GB/T 32586 比距三档对照。',\n  formula: [\n    '底线：一般区段 ≥1400 mm；V 形天窗上、下行正线间分段串 ≥1600 mm',\n    'GB/T 32586 统一爬电比距三档：正常 24~33、非正常 36~40、苛刻 >48 mm/kV',\n  ],\n  references: [\n    'TB 10009-2016 第 5.3.2 条第 1 款（绝对底线）',\n    'GB/T 32586-2016 第 4.4 条（统一爬电比距三档，按系统最高持续电压折算）',\n    '铁路体系以绝对值门槛判定，比距法仅作对照',\n  ],\n  scope: ['爬电距离：600~2500 mm', '系统最高电压：27.5~31 kV'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/creepage/',\n};\n","export { creepageMeta } from './meta';\n\n/** 接触网绝缘爬电距离底线（TB 10009-2016 第 5.3.2 条第 1 款），mm */\nexport const CREEPAGE_FLOOR_GENERAL = 1400;\n/** V 形天窗区段上、下行正线间分段绝缘子串底线，mm */\nexport const CREEPAGE_FLOOR_VCUT = 1600;\n\n/** GB/T 32586 统一爬电比距三档（第 4.4 条，按系统最高持续电压折算） */\nexport const USCD_BANDS = [\n  { label: '正常', min: 24, max: 33 },\n  { label: '非正常', min: 36, max: 40 },\n  { label: '苛刻', min: 48, max: Infinity },\n] as const;\n\n/** 爬电距离校核 */\nexport function creepageCheck(input: {\n  /** 绝缘子实际爬电距离，mm */\n  readonly creepageMM: number;\n  /** 使用场景：'general' 一般 | 'vcut' V 形天窗分段串 */\n  readonly scenario?: 'general' | 'vcut';\n  /** 系统最高电压，kV（GB/T 32586 折算用，默认 29） */\n  readonly maxVoltageKV?: number;\n}): {\n  floorMM: number; passes: boolean; uscdBands: { label: string; mm: number }[];\n} {\n  const floorMM = (input.scenario === 'vcut' ? CREEPAGE_FLOOR_VCUT : CREEPAGE_FLOOR_GENERAL);\n  const kv = input.maxVoltageKV ?? 29;\n  const uscdBands = USCD_BANDS.map((b) => ({\n    label: b.label,\n    mm: b.max === Infinity ? Math.round(b.min * kv) : Math.round(b.min * kv),\n  }));\n  return { floorMM, passes: input.creepageMM >= floorMM, uscdBands };\n}\n"]}

package/dist/chunk-PYNVEHGR.cjs.map

@@ -1 +0,0 @@
-{"version":3,"sources":["/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-PYNVEHGR.cjs","../src/sag/meta.ts","../src/sag/index.ts"],"names":["sagMM"],"mappings":"AAAA;ACEO,IAAM,QAAA,EAA0B;AAAA,EACrC,IAAA,EAAM,2EAAA;AAAA,EACN,MAAA,EAAQ,uBAAA;AAAA,EACR,OAAA,EAAS,sLAAA;AAAA,EACT,OAAA,EAAS;AAAA,IACP,kCAAA;AAAA,IACA,kDAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,UAAA,EAAY;AAAA,IACV,oQAAA;AAAA,IACA;AAAA,EACF,CAAA;AAAA,EACA,KAAA,EAAO,CAAC,6BAAA,EAAgB,4BAAA,EAAe,oCAAgB,CAAA;AAAA,EACvD,UAAA,EAAY,sKAAA;AAAA,EACZ,MAAA,EAAQ;AACV,CAAA;ADAA;AACA;AENO,SAAS,KAAA,CAAM,KAAA,EAAyB;AAC7C,EAAA,MAAM,EAAE,SAAA,EAAW,KAAA,EAAO,YAAY,EAAA,EAAI,KAAA;AAC1C,EAAA,GAAA,CAAI,CAAA,CAAE,UAAA,EAAY,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,0DAAA,EAAe,UAAA,EAAY,KAAK,CAAA;AAC3E,EAAA,GAAA,CAAI,CAAA,CAAE,MAAA,EAAQ,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,0DAAA,EAAe,MAAA,EAAQ,IAAI,CAAA;AAClE,EAAA,GAAA,CAAI,CAAA,CAAE,YAAA,GAAe,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,gEAAA,EAAgB,YAAA,EAAc,MAAM,CAAA;AAClF,EAAA,MAAM,KAAA,EAAQ,YAAA,EAAc,MAAA,EAAQ,MAAA,EAAA,CAAU,EAAA,EAAI,UAAA,EAAY,GAAA,CAAA;AAC9D,EAAA,OAAO,KAAA,EAAO,GAAA;AAChB;AAGO,SAAS,gBAAA,CAAiB,WAAA,EAAqB,KAAA,EAAeA,MAAAA,EAAuB;AAC1F,EAAA,GAAA,CAAI,CAAA,CAAEA,OAAAA,EAAQ,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,0DAAA,EAAeA,OAAAA,EAAQ,KAAK,CAAA;AACnE,EAAA,MAAM,KAAA,EAAOA,OAAAA,EAAQ,GAAA;AACrB,EAAA,OAAQ,YAAA,EAAc,MAAA,EAAQ,MAAA,EAAA,CAAU,EAAA,EAAI,IAAA,EAAA,EAAQ,GAAA;AACtD;AAGO,SAAS,eAAA,CAAgB,WAAA,EAAqB,SAAA,EAAmB,UAAA,EAA4B;AAClG,EAAA,GAAA,CAAI,CAAA,CAAE,WAAA,EAAa,CAAA,CAAA,EAAI,MAAM,IAAI,UAAA,CAAW,sEAAA,EAAiB,WAAA,EAAa,KAAK,CAAA;AAC/E,EAAA,MAAM,KAAA,EAAO,WAAA,EAAa,GAAA;AAC1B,EAAA,OAAO,IAAA,CAAK,IAAA,CAAM,EAAA,EAAI,UAAA,EAAY,IAAA,EAAM,KAAA,EAAQ,WAAW,CAAA;AAC7D;AFIA;AACA;AACE;AACA;AACA;AACA;AACF,yIAAC","file":"/home/runner/work/ocs-calculators/ocs-calculators/dist/chunk-PYNVEHGR.cjs","sourcesContent":[null,"import type { CalculatorMeta } from '../types';\n\nexport const sagMeta: CalculatorMeta = {\n  name: '弛度速算（弛度-张力互算）',\n  nameEn: 'Sag Quick Calculation',\n  summary: '等高悬挂抛物线近似（小弛度假设）下弛度、张力与最大跨距互算。',\n  formula: [\n    '弛度 f = g·l²/(8T)',\n    '反算张力 T = g·l²/(8·f)',\n    '反算跨距上限 l_max = √(8·T·f_max/g)',\n  ],\n  references: [\n    '限值（TB 10009-2016 第 5.1.9 条，推荐性「不宜大于」口径）：链形悬挂接触线 150 mm、简单悬挂 250 mm、低速区段 350 mm',\n    '等高悬挂抛物线近似，适用于 f/l ≤ 1/10',\n  ],\n  scope: ['张力 T：1~40 kN', '跨距 l：5~80 m', '单位重 g：5~25 N/m'],\n  disclaimer: '本工具结果仅供参考，工程应用以设计文件为准。详见 DISCLAIMER.md。',\n  online: 'https://www.itswe.com/calculator/sag/',\n};\n","export { sagMeta } from './meta';\n\n/** 弛度计算参数。单位：张力 kN、跨距 m、单位重 N/m。 */\nexport interface SagInput {\n  /** 接触线/承力索张力 T，kN */\n  readonly tensionKN: number;\n  /** 跨距 l，m */\n  readonly spanM: number;\n  /** 单位长度重量 g，N/m */\n  readonly weightNPerM: number;\n}\n\n/** 弛度 f = g·l²/(8T)，mm */\nexport function sagMM(input: SagInput): number {\n  const { tensionKN, spanM, weightNPerM } = input;\n  if (!(tensionKN > 0)) throw new RangeError('张力必须为正，收到 ' + tensionKN + ' kN');\n  if (!(spanM > 0)) throw new RangeError('跨距必须为正，收到 ' + spanM + ' m');\n  if (!(weightNPerM >= 0)) throw new RangeError('单位重不能为负，收到 ' + weightNPerM + ' N/m');\n  const sagM = (weightNPerM * spanM * spanM) / (8 * tensionKN * 1e3);\n  return sagM * 1e3;\n}\n\n/** 反算张力：给定弛度求张力 T = g·l²/(8·f)，kN */\nexport function tensionFromSagKN(weightNPerM: number, spanM: number, sagMM: number): number {\n  if (!(sagMM > 0)) throw new RangeError('弛度必须为正，收到 ' + sagMM + ' mm');\n  const sagM = sagMM / 1e3;\n  return (weightNPerM * spanM * spanM) / (8 * sagM) / 1e3;\n}\n\n/** 反算最大跨距：给定张力与限值弛度 l_max = √(8·T·f_max/g)，m */\nexport function maxSpanFromSagM(weightNPerM: number, tensionKN: number, sagLimitMM: number): number {\n  if (!(sagLimitMM > 0)) throw new RangeError('限值弛度必须为正，收到 ' + sagLimitMM + ' mm');\n  const sagM = sagLimitMM / 1e3;\n  return Math.sqrt((8 * tensionKN * 1e3 * sagM) / weightNPerM);\n}\n"]}