fritzkit 0.0.0-stage → 0.1.1

package/skills/fritzkit/reference/examples.md

@@ -0,0 +1,275 @@
+# fritzkit worked examples
+
+Each example is a complete, valid `part.json` that compiles to a checker-clean `.fzpz`.
+Field reference: [part-json.md](part-json.md). The XIAO ESP32-C6 example (headers, castellated
+pads, a bus; a portrait board, USB at the top) is in [../SKILL.md](../SKILL.md); the second worked example, a pads-only board
+measured from a listing photo, is "Pads-only board measured from a photo" below.
+
+## Brushless ESC with wire leads
+
+A board with no pins at all, only flying wires: battery leads on one side, three motor
+phases on the other, a thin servo cable underneath. Each wire is a `leads` entry; the
+connector is the free end, which plugs into a breadboard. The two ground wires (thick
+battery minus and the servo cable's ground) are the same net, so they are one bus. The
+motor phases are NOT bused: they are three separate outputs.
+
+```json
+{
+  "slug": "esc-30a-example",
+  "title": "30A brushless ESC (wire leads)",
+  "description": "Top view. Battery leads leave the left edge, motor phases the right edge, servo cable the bottom edge.",
+  "label": "A",
+  "outline": { "widthMm": 45, "heightMm": 24, "shape": "rounded", "cornerRadiusMm": 2 },
+  "artwork": {
+    "boardColor": "#1F4FA0",
+    "silkscreen": [{ "kind": "text", "text": "30A ESC", "xMm": 22.5, "yMm": 12, "sizeMm": 2.5 }]
+  },
+  "leads": [
+    {
+      "key": "vbat",
+      "name": "VBAT",
+      "role": "power",
+      "color": "#D02020",
+      "gaugeMm": 2.2,
+      "fromXMm": 0,
+      "fromYMm": 6,
+      "direction": "left",
+      "lengthMm": 40
+    },
+    {
+      "key": "gnd",
+      "name": "GND",
+      "role": "gnd",
+      "color": "#000000",
+      "gaugeMm": 2.2,
+      "fromXMm": 0,
+      "fromYMm": 18,
+      "direction": "left",
+      "lengthMm": 40
+    },
+    {
+      "key": "ma",
+      "name": "A",
+      "role": "other",
+      "color": "#202020",
+      "fromXMm": 45,
+      "fromYMm": 5,
+      "direction": "right",
+      "lengthMm": 30,
+      "description": "motor phase A"
+    },
+    {
+      "key": "mb",
+      "name": "B",
+      "role": "other",
+      "color": "#202020",
+      "fromXMm": 45,
+      "fromYMm": 12,
+      "direction": "right",
+      "lengthMm": 30,
+      "description": "motor phase B"
+    },
+    {
+      "key": "mc",
+      "name": "C",
+      "role": "other",
+      "color": "#202020",
+      "fromXMm": 45,
+      "fromYMm": 19,
+      "direction": "right",
+      "lengthMm": 30,
+      "description": "motor phase C"
+    },
+    {
+      "key": "sig",
+      "name": "SIG",
+      "role": "pwm",
+      "color": "#F0F0F0",
+      "gaugeMm": 0.8,
+      "fromXMm": 10,
+      "fromYMm": 24,
+      "direction": "down",
+      "lengthMm": 30,
+      "description": "servo PWM input"
+    },
+    {
+      "key": "sgnd",
+      "name": "SIG GND",
+      "label": "-",
+      "role": "gnd",
+      "color": "#5A3A1A",
+      "gaugeMm": 0.8,
+      "fromXMm": 12,
+      "fromYMm": 24,
+      "direction": "down",
+      "lengthMm": 30
+    }
+  ],
+  "buses": [{ "id": "GND", "pins": ["gnd", "sgnd"] }]
+}
+```
+
+Notes: if the ESC's servo cable also has a BEC `+5V` wire, add it as a third thin lead with
+`role: "power"`; do not bus it with VBAT (a regulator sits between them).
+
+## 1-channel 5 V relay module
+
+A 3-pin 0.1 in input header on the left (a `headers` entry, vertical column) and a 3-way
+screw terminal on the right (three `pins` with big holes, `type: "female"`, because the
+terminal pitch is 5 mm and the terminal accepts wires). Mounting holes go in
+`outline.holes`.
+
+```json
+{
+  "slug": "relay-1ch-5v-example",
+  "title": "1-channel 5V relay module",
+  "description": "Top view. Input header on the left edge, screw terminal on the right edge.",
+  "label": "K",
+  "outline": {
+    "widthMm": 50,
+    "heightMm": 26,
+    "shape": "rect",
+    "holes": [
+      { "xMm": 3, "yMm": 3, "dMm": 3 },
+      { "xMm": 47, "yMm": 3, "dMm": 3 }
+    ]
+  },
+  "artwork": {
+    "boardColor": "#1B4F9C",
+    "components": [
+      {
+        "kind": "rect",
+        "xMm": 16,
+        "yMm": 5,
+        "wMm": 19,
+        "hMm": 15.5,
+        "color": "#2060D0",
+        "note": "relay can"
+      }
+    ]
+  },
+  "headers": [
+    {
+      "key": "in",
+      "kind": "male",
+      "cols": 3,
+      "orientation": "vertical",
+      "xMm": 2.5,
+      "yMm": 10.46,
+      "pins": [
+        { "key": "vcc", "name": "VCC", "role": "power" },
+        { "key": "gnd", "name": "GND", "role": "gnd" },
+        { "key": "in1", "name": "IN", "role": "io", "description": "relay driver input" }
+      ]
+    }
+  ],
+  "pins": [
+    {
+      "key": "no",
+      "name": "NO",
+      "type": "female",
+      "role": "other",
+      "xMm": 46,
+      "yMm": 8,
+      "pad": { "shape": "round", "wMm": 3, "hMm": 3, "holeMm": 1.3 },
+      "description": "screw terminal: normally open"
+    },
+    {
+      "key": "com",
+      "name": "COM",
+      "type": "female",
+      "role": "other",
+      "xMm": 46,
+      "yMm": 13,
+      "pad": { "shape": "round", "wMm": 3, "hMm": 3, "holeMm": 1.3 },
+      "description": "screw terminal: common"
+    },
+    {
+      "key": "nc",
+      "name": "NC",
+      "type": "female",
+      "role": "other",
+      "xMm": 46,
+      "yMm": 18,
+      "pad": { "shape": "round", "wMm": 3, "hMm": 3, "holeMm": 1.3 },
+      "description": "screw terminal: normally closed"
+    }
+  ]
+}
+```
+
+Notes: NO, COM and NC are three different nets; no bus. Modules with an extra `JD-VCC`
+jumper header get those pins as a second header; bus `VCC` with `JD-VCC` only if the jumper
+is a fixed trace, not a removable jumper.
+
+## Pads-only board measured from a photo (HW-391 2S 20A balance board)
+
+The full spec is [examples/hw391-2s-20a-bms/part.json](../../../examples/hw391-2s-20a-bms/part.json)
+(see its [README](../../../examples/hw391-2s-20a-bms/README.md) for the measured-vs-golden
+table). It was built by a fresh agent from an Amazon listing using only this skill and the
+CLI. What it shows:
+
+- No headers, no leads: five through-hole solder pads, each a `pins` entry with
+  `type: "female"` and a measured `pad` (`rect`, `wMm`, `hMm`, `holeMm`). Outline 48 x 20 mm
+  from the listing's dimension callout; pad centres from the orthographic top photo at a
+  known px/mm (the `measure.py` `bbox` and `grid` helpers), good to about 0.3 mm.
+- Conventional names for symbol-only silkscreen: the charger/load pads are printed as a plus
+  or minus inside a circle, so `name` is `P+` / `P-` and the `description` says what is
+  printed. The cell pads keep their printed text (`0V`, `4.2V`, `8.4V`).
+- An INFERRED bus: `8.4V` and `P+` look like one copper pour on the back photo, so
+  `"buses": [{ "id": "BPLUS", "pins": ["bplus", "pplus"] }]`. `0V` and `P-` are NOT bused (the
+  MOSFETs sit between them). Inferred nets belong in the report as "check with a meter".
+- Position and size, abridged (all in mm, origin top-left, x right, y down):
+
+```json
+{
+  "outline": { "widthMm": 48, "heightMm": 20, "shape": "rect" },
+  "pins": [
+    {
+      "key": "pplus",
+      "name": "P+",
+      "description": "Charge/discharge plus (silkscreen: plus in a circle); same copper as 8.4V",
+      "role": "power",
+      "type": "female",
+      "xMm": 7.55,
+      "yMm": 12.6,
+      "pad": { "shape": "rect", "wMm": 4.3, "hMm": 3.1, "holeMm": 1.9 }
+    },
+    {
+      "key": "bplus",
+      "name": "8.4V",
+      "role": "power",
+      "type": "female",
+      "xMm": 45.85,
+      "yMm": 17.4,
+      "pad": { "shape": "rect", "wMm": 4.3, "hMm": 3.1, "holeMm": 1.6 }
+    }
+  ],
+  "buses": [{ "id": "BPLUS", "pins": ["bplus", "pplus"] }]
+}
+```
+
+Lessons: verify the silkscreen model in the photo matches the listing title before
+measuring; use a dimension callout for the outline and the photo only for pad positions;
+the rectangular pads render as solid copper in the PCB preview, the drill is in the SVG
+ring (see "Reading the PCB preview" in [../SKILL.md](../SKILL.md)).
+
+## Starting from a KiCad footprint
+
+When a `.kicad_mod` exists (manufacturer download, SnapEDA, KiCad library):
+
+```
+fritzkit import-kicad path/to/Module.kicad_mod --slug my-module
+```
+
+This writes a part with exact pad positions and sizes (through-hole pads -> `type: "female"`
+with `holeMm`; SMD pads -> `type: "pad"`, `smd: true`; non-plated holes -> `outline.holes`;
+pads that share a KiCad number -> tied by a bus). The outline comes from the board edge,
+courtyard, fab layer or the pad bounding box, in that order. Pads on a 2.54 mm grid stay as
+individual pins (exact geometry), they are not converted to headers.
+
+What you still do: replace the KiCad pad numbers in `name` with the real signal names from
+the datasheet, set every `role`, add buses for pads that share a net but have different
+KiCad numbers, set `title`, `description`, `sources` and artwork, then validate and render
+as usual. Check the orientation: KiCad footprints are drawn from the top, y down, the same
+frame as fritzkit.

package/skills/fritzkit/reference/part-json.md

@@ -0,0 +1,333 @@
+<!-- Copy of docs/part-json.md, shipped with the skill so it works when the skill folder is
+     copied on its own. Edit docs/part-json.md and copy it here; keep the two identical
+     except the relative links in "Worked examples". -->
+
+# part.json reference
+
+Every fritzkit part is one folder: `part.json` plus an optional `assets/` folder. This page
+documents every field of `part.json`. The source of truth is the zod schema in
+`src/core/schema/part.ts`; the published JSON Schema (`fritzkit schema`, or
+`src/core/schema/part.schema.json`) is generated from it. If this page and the schema ever
+disagree, the schema wins.
+
+```
+<workspace>/<slug>/part.json          the spec (you write this)
+<workspace>/<slug>/assets/...         photos, datasheet crops (artwork.photo.src points here)
+<workspace>/<slug>/build/...          render output (never read back)
+<workspace>/<slug>/<moduleId>.fzpz    export output (never read back)
+```
+
+The workspace defaults to `~/fritzkit/parts`; override it with `--workspace <dir>` or the
+`FRITZKIT_WORKSPACE` environment variable. Only `part.json` and `assets/` feed the
+compiler.
+
+## Units and the coordinate frame
+
+- **Every length is in millimetres** (fields end in `Mm`). fritzkit converts to mils when it
+  writes SVG; you never deal with inches, mils or pixels in the spec.
+- **Origin = the top-left corner of the outline.** x grows to the RIGHT along `widthMm`,
+  y grows DOWN along `heightMm`. This is the orientation of a top-down photo of the board on
+  screen, so a pixel in an orthographic photo maps straight to mm:
+  `xMm = (px - boardLeftPx) / pxPerMm`, `yMm = (py - boardTopPx) / pxPerMm`.
+- **Positions are centres.** A pin's `xMm`/`yMm` is the centre of its pad; a header's
+  `xMm`/`yMm` is the centre of its FIRST pin; a hole's `xMm`/`yMm` is its centre. Only
+  `rect` silk items use their top-left corner.
+- **Pad sizes are in the part frame and never rotated:** `pad.wMm` is the extent along x,
+  `pad.hMm` the extent along y, whatever the header orientation.
+- Pins, leads and overhanging parts may lie OUTSIDE the outline (negative coordinates or
+  beyond the outline size). The compiler grows the drawing canvas to fit them.
+- If the part has headers, the compiler shifts the whole drawing so the first header pin
+  lands exactly on Fritzing's 0.1 in (100 mil) grid; that is what makes the part seat in a
+  breadboard. You do nothing for this; just keep header pins at their true pitch.
+- The drawing shows the TOP (component) side. A pad that exists only on the back is placed
+  where it would be seen through the board from the top (same x/y as from the top).
+
+## Top level
+
+| field         | type                            | default       | notes                                                                                                                                  |
+| ------------- | ------------------------------- | ------------- | -------------------------------------------------------------------------------------------------------------------------------------- |
+| `$schema`     | string                          | -             | optional; `fritzkit new` writes the published schema URL so editors validate as you type                                               |
+| `slug`        | string, 3-60 chars              | **required**  | lowercase letters, digits and `-`, starting and ending with a letter or digit (`xiao-esp32-c6`). Names the folder and the moduleId     |
+| `title`       | string, 1-120                   | **required**  | shown in Fritzing's Inspector and parts bin                                                                                            |
+| `version`     | integer >= 1                    | `1`           | bump by hand when the part changes materially; shown in the variant as `v<version> <hash8>`                                            |
+| `family`      | string, 1-60                    | the slug      | Fritzing swap group: parts in one family can be swapped in the Inspector. Leave unset unless several slugs should swap with each other |
+| `label`       | string, 1-4                     | `"A"`         | reference designator prefix: `A` module/board, `U` IC or MCU board, `J` connector, `K` relay, `M` motor                                |
+| `author`      | string, max 80                  | `"fritzkit"`  |                                                                                                                                        |
+| `tags`        | string[] (each 1-30)            | `[]`          | search keywords for Fritzing's parts search                                                                                            |
+| `description` | string, max 4000                | `""`          | plain text; say what the part is and which side and orientation the drawing shows                                                      |
+| `sources`     | URL[]                           | `[]`          | listing, wiki and datasheet URLs (must be valid URLs); appended to the description in Fritzing                                         |
+| `properties`  | object string -> string         | `{}`          | extra Inspector properties (`mpn`, `type`, `voltage`, `chip` ...). Keys and values must be non-empty. `family`/`variant` are automatic |
+| `outline`     | [Outline](#outline)             | **required**  | board size and shape                                                                                                                   |
+| `artwork`     | [Artwork](#artwork)             | `{}` (vector) | how the breadboard view looks                                                                                                          |
+| `pins`        | [Pin](#pin)[]                   | `[]`          | free-standing pads or pins at arbitrary positions                                                                                      |
+| `headers`     | [Header](#header)[]             | `[]`          | rows/grids of pins at a fixed pitch (0.1 in headers, castellated edges)                                                                |
+| `leads`       | [Lead](#lead)[]                 | `[]`          | flying wire leads with a connector at the free end                                                                                     |
+| `pinIds`      | object key -> integer >= 0      | `{}`          | **managed by fritzkit; never edit by hand.** See [pinIds](#pinids)                                                                     |
+| `buses`       | [Bus](#bus)[]                   | `[]`          | connectors that are the same electrical node (e.g. several GND pads)                                                                   |
+| `spice`       | [Spice](#spice)                 | -             | optional simulator model                                                                                                               |
+| `schematic`   | [schematic options](#schematic) | `{}`          | schematic symbol layout                                                                                                                |
+| `pcb`         | [pcb options](#pcb)             | `{}`          | PCB footprint options                                                                                                                  |
+
+Unknown keys are rejected everywhere (every object is strict), so a typo such as
+`"widthmm"` is an error instead of being silently ignored.
+
+## Fields shared by pins, header pins and leads
+
+| field         | type            | default      | notes                                                                                                                           |
+| ------------- | --------------- | ------------ | ------------------------------------------------------------------------------------------------------------------------------- |
+| `key`         | string          | **required** | stable identifier, unique across the whole part. Letters, digits, `_ . + -`; must not start with `.`, `+` or `-`. Never rename  |
+| `name`        | string, 1-40    | **required** | the connector name Fritzing shows on hover and in the Inspector. Use the silkscreen text (`GND`, `D7`, `NO`), never `pin1`      |
+| `label`       | string, max 16  | the name     | text drawn next to the pin (breadboard and schematic); `""` hides the breadboard label; the fzp connector name is always `name` |
+| `description` | string, max 400 | the name     | function, voltage, alternate functions (`D4 / SDA`)                                                                             |
+| `role`        | enum            | `"io"`       | `power`, `gnd`, `io`, `analog`, `pwm`, `i2c`, `spi`, `uart`, `usb`, `clock`, `reset`, `enable`, `nc`, `other`                   |
+
+`role` decides where the pin goes on the schematic symbol (see [schematic](#schematic)) and
+its label colour. Use `power` for every supply pin (VCC, 5V, 3V3, VBAT, VIN), `gnd` for every
+ground, `nc` for pins that are not connected, `other` for things like relay contacts and
+motor phases.
+
+Symbol-only or non-Latin silkscreen (a plus in a circle, Chinese text): `name` is the
+conventional ASCII function name (`P+`, `P-`, `VCC`); the printed symbol or the translation
+goes in `description`. Names and labels are ASCII only.
+
+## Pin
+
+A pad or pin at an arbitrary position: solder pads, screw terminals, odd pin spacings, test
+pads, anything not on a regular grid.
+
+| field                               | type                               | default                                                | notes                                                               |
+| ----------------------------------- | ---------------------------------- | ------------------------------------------------------ | ------------------------------------------------------------------- |
+| key, name, label, description, role | see above                          |                                                        |                                                                     |
+| `type`                              | `female` / `male` / `pad` / `wire` | `"female"`                                             | see below                                                           |
+| `xMm`                               | number                             | **required**                                           | pad centre, part frame                                              |
+| `yMm`                               | number                             | **required**                                           | pad centre, part frame                                              |
+| `pad`                               | [PadGeometry](#padgeometry)        | `{ "shape": "rect", "wMm": 2, "hMm": 2, "holeMm": 1 }` | copper size and drill                                               |
+| `snap`                              | boolean                            | -                                                      | UI hint only: snap to the 0.1 in grid when dragged in `fritzkit ui` |
+
+Connector `type` (what Fritzing lets attach to it):
+
+- `female` - a wire or a male pin attaches to it: through-hole solder pads, female header
+  sockets, screw terminals. The default, and the right choice for most pads with a hole.
+- `male` - it plugs into a breadboard or socket: header pins.
+- `pad` - a surface pad with no hole: SMD pads, castellated edges, test pads.
+- `wire` - reserved by Fritzing for its own wires; do not use it (leads are emitted as
+  `male` automatically).
+
+## PadGeometry
+
+| field    | type                      | default      | notes                                                           |
+| -------- | ------------------------- | ------------ | --------------------------------------------------------------- |
+| `shape`  | `rect` / `round` / `oval` | `"rect"`     | copper shape                                                    |
+| `wMm`    | number > 0                | **required** | copper extent along x                                           |
+| `hMm`    | number > 0                | **required** | copper extent along y                                           |
+| `holeMm` | number >= 0               | -            | drill diameter; absent or 0 = no hole (SMD, top copper only)    |
+| `smd`    | boolean                   | -            | force SMD (no drill, top copper only) even when `holeMm` is set |
+
+In the PCB view a pad with a hole becomes a through-hole pad on both copper layers. Fritzing
+needs a minimum hole and annular ring, so very small holes are drawn slightly bigger.
+
+The PCB SVG draws the pad as a ring: a `<circle fill="none">` whose stroke is the copper, so
+`drill = 2 * (r - stroke-width / 2)` and `copper = 2 * (r + stroke-width / 2)` (mils). Oblong
+and rectangular pads also get a solid copper rect under the ring, so a preview PNG can look
+like a solid block; the drill is still the ring's empty centre.
+
+## Header
+
+A row or grid of pins at a fixed pitch, drawn in Fritzing's house style.
+
+| field         | type                              | default        | notes                                                                                                    |
+| ------------- | --------------------------------- | -------------- | -------------------------------------------------------------------------------------------------------- |
+| `key`         | string                            | **required**   | identifies the header (not a connector)                                                                  |
+| `kind`        | `male` / `female` / `castellated` | `"male"`       | male pins, female sockets, or castellated (half-hole) SMD edge pads                                      |
+| `pitchMm`     | number > 0                        | `2.54`         | centre-to-centre spacing, both directions                                                                |
+| `rows`        | integer 1-8                       | `1`            |                                                                                                          |
+| `cols`        | integer 1-64                      | **required**   |                                                                                                          |
+| `xMm`, `yMm`  | number                            | **required**   | centre of the FIRST pin (row 0, col 0)                                                                   |
+| `orientation` | `horizontal` / `vertical`         | `"horizontal"` | horizontal: cols run along +x, rows along +y. vertical: cols run along +y (down), rows along +x (right)  |
+| `pins`        | (HeaderPin or `null`)[]           | **required**   | exactly `rows * cols` entries, row-major (row 0 col 0, row 0 col 1, ...). `null` leaves a position empty |
+| `pad`         | [PadGeometry](#padgeometry)       | see below      | copper override                                                                                          |
+
+A HeaderPin has only `key`, `name`, `label`, `description` and `role`. Its position comes
+from the grid and its connector type from `kind` (male -> `male`, female -> `female`,
+castellated -> `pad`).
+
+Default copper: male/female = round 1.6 mm pad with a 1.0 mm hole (through-hole);
+castellated = rect 1.6 x 2.4 mm SMD (`wMm` along x, `hMm` along y). The castellated default
+suits a HORIZONTAL row along the top or bottom edge. For a VERTICAL column along the left or
+right edge set `"pad": { "shape": "rect", "wMm": 2.4, "hMm": 1.6, "smd": true }` so the long
+side points into the board.
+
+Examples: a 1x7 row with pin 1 at the left is
+`{ "key": "j1", "cols": 7, "xMm": <x of pin 1>, "yMm": <y>, "pins": [7 entries] }`; a 2x20
+header is `{ "rows": 2, "cols": 20, ... }` with 40 entries (all of row 0, then all of row 1).
+Two rows that are NOT one pitch apart (the two sides of a DIP-style module) are two separate
+headers.
+
+## Lead
+
+A flying wire (motor phases, battery leads, a servo cable). Drawn as a bendable leg; the
+connector is the free end, which plugs into a breadboard like a male pin.
+
+| field                               | type                             | default      | notes                                                         |
+| ----------------------------------- | -------------------------------- | ------------ | ------------------------------------------------------------- |
+| key, name, label, description, role | see above                        |              |                                                               |
+| `fromXMm`, `fromYMm`                | number                           | **required** | where the wire leaves the board (usually on the outline edge) |
+| `direction`                         | `left` / `right` / `up` / `down` | `"left"`     | which way the wire runs from that point                       |
+| `lengthMm`                          | number > 0                       | `40`         | drawn length; the free end is `lengthMm` away in `direction`  |
+| `color`                             | `#RRGGBB`                        | `"#000000"`  | insulation colour                                             |
+| `gaugeMm`                           | number > 0                       | `1.6`        | wire outer diameter, for drawing                              |
+
+Leads have no `type` or `pad` field. In the PCB view a lead becomes a through-hole pad
+(unless `pcb.mode` is `smd`).
+
+## Outline
+
+| field            | type                          | default      | notes                                                                          |
+| ---------------- | ----------------------------- | ------------ | ------------------------------------------------------------------------------ |
+| `widthMm`        | number > 0                    | **required** | extent along x. Convention: put the LONG edge on x                             |
+| `heightMm`       | number > 0                    | **required** | extent along y                                                                 |
+| `shape`          | `rect` / `rounded` / `custom` | `"rounded"`  |                                                                                |
+| `cornerRadiusMm` | number >= 0                   | `1`          | used by `rounded`                                                              |
+| `pathMm`         | string                        | -            | for `custom`: an SVG path in mm, part frame, e.g. `"M0 0 H30 V10 L25 15 H0 Z"` |
+| `holes`          | `{ xMm, yMm, dMm }`[]         | `[]`         | mounting holes (centre, diameter); drawn in breadboard and PCB, not connectors |
+
+## Artwork
+
+How the breadboard view is drawn. The schematic, PCB and icon views are always generated
+from the pins and the outline.
+
+| field        | type                    | default     | notes                                                                                |
+| ------------ | ----------------------- | ----------- | ------------------------------------------------------------------------------------ |
+| `style`      | `vector` / `photo`      | `"vector"`  | vector = Fritzing house style; photo = embedded raster with vector pads on top       |
+| `boardColor` | `#RRGGBB`               | `"#1B7F3B"` | PCB colour (green). Black `#1A1A1A`, blue `#1B4F9C`, red `#B0242A`, purple `#5B2A86` |
+| `silkColor`  | `#RRGGBB`               | `"#FFFFFF"` | silkscreen colour                                                                    |
+| `silkscreen` | [SilkItem](#silkitem)[] | `[]`        | text and lines printed on the board                                                  |
+| `components` | [SilkItem](#silkitem)[] | `[]`        | large components drawn as shapes (USB socket, relay can, chip, heatsink)             |
+| `photo`      | [Photo](#photo)         | -           | required when `style` is `photo`                                                     |
+
+Draw only the components that help a user recognise the board and find pin 1 (the USB
+connector, a relay can, a big chip). Do not draw every resistor. fritzkit labels every pin
+already, so do not repeat pin names in `silkscreen`. Component shapes are drawn on top of
+silkscreen text (pads are drawn on top of both), so keep text off component shapes or it is
+hidden. Silkscreen and components are drawn under header bodies, pads and pin labels, so
+put text where pads are not.
+
+### SilkItem
+
+A union on `kind`. All positions in mm, part frame.
+
+| kind     | fields (default)                                                                                                                                 |
+| -------- | ------------------------------------------------------------------------------------------------------------------------------------------------ |
+| `text`   | `text` (1-80, required), `xMm`, `yMm`, `sizeMm` (`1.2`), `color` (`#FFFFFF`), `anchor` `start`/`middle`/`end` (`middle`), `rotate` degrees (`0`) |
+| `rect`   | `xMm`, `yMm` (TOP-LEFT corner), `wMm`, `hMm`, `color` (`#222222`), `rxMm` corner radius (`0`), `note` (not rendered)                             |
+| `circle` | `xMm`, `yMm` (centre), `dMm` diameter, `color` (`#222222`), `note`                                                                               |
+| `line`   | `x1Mm`, `y1Mm`, `x2Mm`, `y2Mm`, `widthMm` (`0.2`), `color` (`#FFFFFF`)                                                                           |
+
+### Photo
+
+| field              | type                       | default      | notes                                                                           |
+| ------------------ | -------------------------- | ------------ | ------------------------------------------------------------------------------- |
+| `src`              | string                     | **required** | path relative to the part folder, e.g. `"assets/top.jpg"`                       |
+| `crop`             | `[x, y, w, h]` (pixels)    | -            | crop rectangle in source pixels, applied BEFORE rotation                        |
+| `rotate`           | `0` / `90` / `180` / `270` | `0`          | clockwise, applied after the crop, so the board ends up in the spec orientation |
+| `removeBackground` | boolean                    | `true`       | key out a near-white listing background and trim to the board                   |
+| `opacity`          | number 0-1                 | `1`          |                                                                                 |
+
+After crop, rotate and trim the image is stretched over the outline rectangle, so the board
+must fill the processed image edge to edge (that is what `removeBackground` trims to; with
+`removeBackground: false`, crop exactly to the board). The image is downscaled to at most
+1600 px wide. Pads are still drawn as vector shapes on top, at the spec positions.
+
+## Bus
+
+| field  | type                    | notes                                                 |
+| ------ | ----------------------- | ----------------------------------------------------- |
+| `id`   | string (`A-Za-z0-9_.-`) | unique, e.g. `GND`, `VBAT`                            |
+| `pins` | pin key[] (>= 2)        | keys of pins, header pins or leads that share one net |
+
+A bus tells Fritzing that the connectors are one electrical node, so a wire to one GND pad
+counts as connected to every GND pad (ratsnest, routing checks). A connector can be in at
+most one bus. Bus pins that are really the same copper: several `GND` pads, two `VIN` pads
+tied together, a screw terminal paralleled with a solder pad. Pins that merely have similar
+names (two `+` pads on different nets, `IN1` and `IN2`, `VCC` and `5V` with a regulator
+between them) are NOT a bus unless the copper is visibly shared or the datasheet says so.
+
+## pinIds
+
+`pinIds` maps every pin key to its Fritzing connector number (`connector0`, `connector1`,
+...). fritzkit fills it in: the first `validate`, `render` or `export` after you add a pin
+gives the new key the next free number and writes it back to `part.json`. Numbers are never
+reused, so when you delete a pin its number stays reserved and every other pin keeps its id.
+That is what lets Fritzing swap a placed copy for a newer version without dropping wires.
+
+fritzkit manages `pinIds`: do not hand-edit them for a part that has ever been
+exported/installed (connector ids must stay stable). For a brand-new part you may delete
+the `pinIds` object before the first export to close gaps. Never reuse a key for a
+different physical pin;
+rename a pin by changing `name`, not `key`. A new spec may omit `pinIds` or write `{}`. Gaps
+in the numbering after a pin was removed produce a harmless `connector-numbering` warning
+(only a warning).
+
+## Spice
+
+| field   | type     | notes                              |
+| ------- | -------- | ---------------------------------- |
+| `model` | string   | optional `.model` / `.subckt` text |
+| `lines` | string[] | at least one netlist line          |
+
+Tokens: `{instanceTitle}`, `{net connectorN}` (N from `pinIds`, so add spice AFTER the first
+validate), and `{<property>}` for any entry in `properties`. A battery with internal
+resistance, where connector0 is minus and connector1 is plus:
+
+```json
+{
+  "properties": { "voltage": "3.7V", "internal resistance": "0.05" },
+  "spice": {
+    "lines": [
+      "V{instanceTitle} {net connector1}_{instanceTitle}_aux {net connector0} DC {voltage}",
+      "R{instanceTitle} {net connector1}_{instanceTitle}_aux {net connector1} {internal resistance}"
+    ]
+  }
+}
+```
+
+Parts without `spice` are greyed out in Fritzing's simulator, which is normal for modules
+and MCU boards.
+
+## schematic
+
+| field    | type                                       | default     | notes                                      |
+| -------- | ------------------------------------------ | ----------- | ------------------------------------------ |
+| `layout` | `by-role`                                  | `"by-role"` | an auto-sized rectangle on the 0.1 in grid |
+| `sides`  | `{ left?, right?, top?, bottom? }`, role[] | -           | override which side each role lands on     |
+
+Behaviour of `by-role`: one box; pins are grouped by role onto sides, in spec order within
+a role; every bused GND pin still gets its own pin. Default sides: power, usb, enable and
+reset on the left, gnd at the bottom, everything else on the right. An empty `label` is
+drawn as an empty pin label (it does not fall back to `name`). An explicit per-pin ordering
+hint is not available yet.
+Example override:
+`"schematic": { "sides": { "left": ["power", "gnd"], "right": ["io", "i2c", "spi", "uart", "analog", "pwm"] } }`.
+
+## pcb
+
+| field               | type                   | default  | notes                                                               |
+| ------------------- | ---------------------- | -------- | ------------------------------------------------------------------- |
+| `mode`              | `auto` / `tht` / `smd` | `"auto"` | auto: per pad (a hole means through-hole); tht / smd force all pads |
+| `silkscreenOutline` | boolean                | `true`   | draw the board outline on the PCB silkscreen                        |
+
+## Identity (computed, not in the spec)
+
+- `moduleId = fritzkit-<slug>-<hash8>`; `hash8` hashes part.json (minus `$schema`) and every
+  file in `assets/`. Any change gives a new moduleId, because Fritzing refuses to import a
+  moduleId it already has.
+- `family = family ?? slug` (stable) and `variant = v<version> <hash8>` (unique per export).
+  In Fritzing, select a placed part and pick another variant in the Inspector to swap it.
+
+## Worked examples
+
+Complete, valid specs live in the skill's
+[examples.md](examples.md): the Seeed XIAO ESP32-C6 (headers and a
+bus), an ESC with wire leads, a relay module, a KiCad import, and the pads-only HW-391
+board measured from a listing photo. The full XIAO spec is also in
+[SKILL.md](../SKILL.md) (a portrait board, USB at the top).