edfcore 0.5.4 → 0.5.6

package/dist/constants.d.ts

@@ -109,5 +109,5 @@ export declare const SIGNAL_FIELD_BLOCK_OFFSETS: {
     readonly reserved: 224;
 };
 /** Published package version. Kept in sync with package.json by a test. */
-export declare const VERSION = "0.5.4";
+export declare const VERSION = "0.5.6";
 //# sourceMappingURL=constants.d.ts.map

package/dist/constants.js

@@ -79,5 +79,5 @@ export const SIGNAL_FIELD_BLOCK_OFFSETS = {
     reserved: 224,
 };
 /** Published package version. Kept in sync with package.json by a test. */
-export const VERSION = '0.5.4';
+export const VERSION = '0.5.6';
 //# sourceMappingURL=constants.js.map

package/docs/CHANGELOG.md

@@ -6,6 +6,48 @@ alone does not tell you whether you were affected.
 edfcore is pre-1.0. Patch releases have carried behaviour changes where the old behaviour was a
 defect; those are called out below.
 
+## 0.5.6
+
+- **Fixed** two lines of the `EdfSignal` block on `api-types.md` describing a different file from
+  the other five. The page prints one running example — six one-second records, one 100-sample
+  signal — and its test builds that file and checks `index`, `kind`, `samplesPerRecord`,
+  `sampleRateHz` and `sampleCount`. It stopped there, and the two lines it stopped before are the
+  two that would have failed: `signal.scale` prints a bitValue of `0.1221001221001221` and
+  `signal.raw.digitalMinimum` prints `'-2048   '`, while the fixture took the writer's defaults and
+  produced `0.015259021896696421` and `'-32768  '`.
+- The page is the specification and the fixture is the reconstruction, so the fixture moved: the
+  printed values imply 500 µV over 4,095 digital steps and nothing else, and the conventions
+  paragraph at the top of the page introduces the "exposed twice" rule with the same `-2048` as its
+  example. Declaring `-250`..`250` over `-2048`..`2047` makes every line of the block true of one
+  file, and makes the sentence at the top true of it too.
+- `bitValue` is re-derived through the pinned expression from the declared fields rather than
+  compared against the printed float. It is the number a reader checks their own port against, and
+  copying the page's sixteen digits into the test would make the two agree without either being
+  right.
+- The whole block is now under test, including the raw field with its padding intact — compared
+  against the page without collapsing whitespace, since collapsing turns `'-2048   '` into
+  `'-2048 '` and quietly passes the check the sentence exists to make.
+
+## 0.5.5
+
+- **Added** the table under "Files with several sample rates" on `reading-signals.md`, and the
+  sentence after it. Nine numbers — three channels' `samplesPerRecord`, `sampleCount` and
+  `firstSampleIndex` over `[10, 14)`, then three more counts after trimming the same chunk to
+  `[10.5, 12.5)` — and none had been run. `multi-signal-cost.test.ts` covers a different table on
+  the same page and `reading-signals-arithmetic.test.ts` the section above it.
+- The last sentence is the one worth having under test: "The temperature channel's trimmed window
+  starts at 11 s rather than 10.5 s. At 1 Hz there's no sample at 10.5, and the first one inside the
+  window is the one at 11." That is `startSeconds` becoming genuinely per-signal — before the trim
+  all three share a value, because a record-aligned read starts every channel at the same record,
+  and the run asserts that too so the change is visible as a change.
+- It is the difference between a boundary computed on each channel's own grid and one computed from
+  a rate. A viewer that reused the requested 10.5 for all three would draw the temperature trace
+  half a sample to the left, on the one channel where half a sample is half a second. The boundary
+  is checked in ticks as well as seconds.
+- Every figure is read out of the page's own table and prose, so neither side can drift, and the
+  row arithmetic is checked against itself: a sample count is the rate times the window, a first
+  index is the rate times the start.
+
 ## 0.5.4
 
 - **Added** the rest of the block `discontinuous.md` prints for `index.segments` and `index.gaps`.

package/package.json

@@ -1,6 +1,6 @@
 {
   "name": "edfcore",
-  "version": "0.5.4",
+  "version": "0.5.6",
   "description": "Modern, typed, zero-dependency reader for EDF, EDF+, BDF and BDF+ biosignal files. Works in browsers and Node with true random access.",
   "keywords": [
     "edf",

package/src/constants.ts

@@ -93,4 +93,4 @@ export const SIGNAL_FIELD_BLOCK_OFFSETS = {
 } as const;
 
 /** Published package version. Kept in sync with package.json by a test. */
-export const VERSION = '0.5.4';
+export const VERSION = '0.5.6';