edfcore 0.5.3 → 0.5.5

package/dist/constants.d.ts

@@ -109,5 +109,5 @@ export declare const SIGNAL_FIELD_BLOCK_OFFSETS: {
     readonly reserved: 224;
 };
 /** Published package version. Kept in sync with package.json by a test. */
-export declare const VERSION = "0.5.3";
+export declare const VERSION = "0.5.5";
 //# sourceMappingURL=constants.d.ts.map

package/dist/constants.js

@@ -79,5 +79,5 @@ export const SIGNAL_FIELD_BLOCK_OFFSETS = {
     reserved: 224,
 };
 /** Published package version. Kept in sync with package.json by a test. */
-export const VERSION = '0.5.3';
+export const VERSION = '0.5.5';
 //# sourceMappingURL=constants.js.map

package/docs/CHANGELOG.md

@@ -6,6 +6,45 @@ alone does not tell you whether you were affected.
 edfcore is pre-1.0. Patch releases have carried behaviour changes where the old behaviour was a
 defect; those are called out below.
 
+## 0.5.5
+
+- **Added** the table under "Files with several sample rates" on `reading-signals.md`, and the
+  sentence after it. Nine numbers — three channels' `samplesPerRecord`, `sampleCount` and
+  `firstSampleIndex` over `[10, 14)`, then three more counts after trimming the same chunk to
+  `[10.5, 12.5)` — and none had been run. `multi-signal-cost.test.ts` covers a different table on
+  the same page and `reading-signals-arithmetic.test.ts` the section above it.
+- The last sentence is the one worth having under test: "The temperature channel's trimmed window
+  starts at 11 s rather than 10.5 s. At 1 Hz there's no sample at 10.5, and the first one inside the
+  window is the one at 11." That is `startSeconds` becoming genuinely per-signal — before the trim
+  all three share a value, because a record-aligned read starts every channel at the same record,
+  and the run asserts that too so the change is visible as a change.
+- It is the difference between a boundary computed on each channel's own grid and one computed from
+  a rate. A viewer that reused the requested 10.5 for all three would draw the temperature trace
+  half a sample to the left, on the one channel where half a sample is half a second. The boundary
+  is checked in ticks as well as seconds.
+- Every figure is read out of the page's own table and prose, so neither side can drift, and the
+  row arithmetic is checked against itself: a sample count is the rate times the window, a first
+  index is the rate times the start.
+
+## 0.5.4
+
+- **Added** the rest of the block `discontinuous.md` prints for `index.segments` and `index.gaps`.
+  The page prints three objects in full — fifteen fields between them — and the tests checked four:
+  the two record ranges and the two `startSeconds`. Each segment's own `index`, its `startTicks`,
+  its `endSeconds`, and the gap's `beforeSegmentIndex`/`afterSegmentIndex` were printed and never
+  run.
+- Those are the fields most worth running. `startTicks` is the exact value the whole time model
+  rests on and the only one a reader cannot check by eye against the diagram above it;
+  `endSeconds` is derived from two other printed numbers, so a page printing all three can
+  contradict itself while every individual number matches something; and the gap's two segment
+  indices are what make it a gap between a specific pair rather than a free-floating interval.
+- The fields are enumerated from the page rather than listed in the test — the block is parsed into
+  objects and each `name: value` compared against the object the scan produced — so a field added to
+  the block is checked by having been printed. Adding `1n` to a segment's `startTicks` fails it.
+- The derived fields are also checked against each other rather than only against the page:
+  `endSeconds` is `startSeconds + durationSeconds` on every segment and gap, and the gap runs from
+  where the earlier segment ends to where the later one starts, in ticks.
+
 ## 0.5.3
 
 - **Added** the claim `api-reading.md` makes in one clause: "that makes `startSeconds` trustworthy

package/package.json

@@ -1,6 +1,6 @@
 {
   "name": "edfcore",
-  "version": "0.5.3",
+  "version": "0.5.5",
   "description": "Modern, typed, zero-dependency reader for EDF, EDF+, BDF and BDF+ biosignal files. Works in browsers and Node with true random access.",
   "keywords": [
     "edf",

package/src/constants.ts

@@ -93,4 +93,4 @@ export const SIGNAL_FIELD_BLOCK_OFFSETS = {
 } as const;
 
 /** Published package version. Kept in sync with package.json by a test. */
-export const VERSION = '0.5.3';
+export const VERSION = '0.5.5';