dsh-engineering-ui 0.0.0-stage → 1.5.1

package/engineering/tools/physics/rules/gb_structural_rules.json

@@ -0,0 +1,201 @@
+{
+  "ruleset_id": "DSVA-GB_STRUCTURAL",
+  "revision": "A",
+  "category": "gb_structural",
+  "generated_from": "DSVA国标对照表.xlsx",
+  "total": 12,
+  "rules": [
+    {
+      "rule_id": "GB_STRUCTURAL-001",
+      "standard_id": "GB 50017-2017",
+      "title": "钢结构设计标准",
+      "topic": "钢结构设计",
+      "scope": "本标准适用于工业与民用建筑和一般构筑物的钢结构设计。",
+      "status": "现行(替代GB 50017-2003；部分强制性条文因GB 55006-2021实施而废止)",
+      "dsva_requirement": "材料设计强度、稳定性、局部屈曲、连接验算、允许长细比",
+      "severity": "BLOCKER",
+      "validation_method": "manual_review",
+      "requires_manual_review": true,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://www.mohurd.gov.cn/gongkai/zc/wjk/art/2018/art_17339_237277.html",
+      "note": "工程建设国标(住建部公告2017年第1771号)；强制性条文第4.3.2、4.4.1、4.4.3~4.4.6、18.3.3条已被GB 55006-2021部分代替(2022-01-01起)"
+    },
+    {
+      "rule_id": "GB_STRUCTURAL-002",
+      "standard_id": "GB/T 985.1-2008",
+      "title": "气焊、焊条电弧焊、气体保护焊和高能束焊的推荐坡口",
+      "topic": "焊接接头",
+      "scope": "GB/T 985 的本部分规定了钢材焊接的坡口形式和尺寸。本部分适用于气焊、焊条电弧焊、气体保护焊和高能束焊接。",
+      "status": "现行(替代GB/T 985-1988)",
+      "dsva_requirement": "坡口形式、焊缝形式、焊脚尺寸、焊透要求",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=3DBC8D7D6FE879681E301D62CE9DDC48",
+      "note": ""
+    },
+    {
+      "rule_id": "GB_STRUCTURAL-003",
+      "standard_id": "GB/T 985.2-2008",
+      "title": "埋弧焊的推荐坡口",
+      "topic": "焊接接头",
+      "scope": "GB/T 985 的本部分规定了钢材焊接的坡口形式和尺寸。本部分适用于埋弧焊工艺方法。",
+      "status": "现行(代替GB/T 986-1988)",
+      "dsva_requirement": "(同上)",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://std.samr.gov.cn/gb/search/gbDetailed?id=2lRLMZyiWTg%3D&mode=p",
+      "note": ""
+    },
+    {
+      "rule_id": "GB_STRUCTURAL-004",
+      "standard_id": "GB/T 3323.1-2019；GB/T 3323.2-2019",
+      "title": "焊缝无损检测 射线检测 第1部分:X和伽玛射线的胶片技术；第2部分:使用数字化探测器的X和伽玛射线技术",
+      "topic": "焊缝质量",
+      "scope": "第1部分：GB/T 3323的本部分规定了金属材料熔化焊焊接接头的射线检测技术。本部分适用于板、管焊接接头或其他焊接接头的射线检测。本部分不包含金属材料焊接接头射线检测的验收等级。如合同各方采用低于本部分的检测条件,检测图像质量极有可能显著下降。第2部分：GB/T 3323的本部分基于数字射线检测基本理论和实际经验,规定了采用计算机射线照相(CR)技术与采用数字阵列探测器(DDA)的数字成像(DR)技术对金属材料焊接接头进行X和伽玛射线数字检测的通用技术和要求,包括X和伽玛射线数字检测技术的技术等级、一般要求及推荐技术(探测器系统选择、透照技术控制、图像采集与显示要求)等内容,规定了获得与本标准第1部分(GB/T 3323.1)基于胶片的射线检测技术同等检测灵敏度的数字检测图像的最低要求。本部分适用于采用存储荧光成像板(IP板)的CR技术与采用数字阵列探测器(DDA)的DR技术,检测板、管焊接接头或其他焊接接头。本部分不包含金属材料焊接接头数字射线检测的验收等级。如合同各方采用低于本部分的检测条件,检测图像质量极有可能显著下降",
+      "status": "现行(两分部分共同代替GB/T 3323-2005,2020-03-01废止)",
+      "dsva_requirement": "无损检测、焊缝缺陷等级、验收等级",
+      "severity": "BLOCKER",
+      "validation_method": "manual_review",
+      "requires_manual_review": true,
+      "is_deprecated": true,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/std/newGbInfo?hcno=5CDEE3B59B905A98F42EC36E56F1979C ；https://openstd.samr.gov.cn/bzgk/std/newGbInfo?hcno=54831989A7A4255AB16794D5EED32456",
+      "note": "修改采用ISO 17636-1:2013、ISO 17636-2:2013；修订计划20254705/20254706-T-604分别征求意见/批准中"
+    },
+    {
+      "rule_id": "GB_STRUCTURAL-005",
+      "standard_id": "GB/T 11345-2023",
+      "title": "焊缝无损检测 超声检测 技术、检测等级和评定",
+      "topic": "焊缝质量",
+      "scope": "本文件描述了母材厚度不小于8mm的低超声衰减（特别是散射衰减小）金属材料熔化焊焊接接头手工超声检测技术。检测时焊缝及其母材温度为0°C~60°C。本文件主要适用于母材和焊缝均为铁素体类钢的全熔透焊缝。本文件描述的材料超声特性，是基于纵波声速为（5920±50）m/s和横波声速为（3255±30）m/s的钢材。本文件描述了四个检测等级。不同的检测等级对应不同的缺欠检出率。本文件适用于通过下列任一技术对其所发现的不连续进行评定或验收： a）基于不连续的长度和回波幅度的评定； b）基于采用探头移动技术获得不连续的特性和尺寸的评定。",
+      "status": "现行(代替GB/T 11345-2013)",
+      "dsva_requirement": "(同上)",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/std/newGbInfo?hcno=74F18273E6C78A39D2B5D0BE347162AB",
+      "note": ""
+    },
+    {
+      "rule_id": "GB_STRUCTURAL-006",
+      "standard_id": "GB/T 12469-1990",
+      "title": "焊接质量保证 钢熔化焊接头的要求和缺陷分级",
+      "topic": "焊缝质量",
+      "scope": "本标准规定了钢熔化焊接头的要求及缺陷的分级。本标准适用于熔焊方法施焊的对接和角接（搭接及T型）接头。",
+      "status": "已废止(废止日期官方平台记录不一致:std.samr为2004-10-14,ndls/cssn为2005-10-14,以官方废止公告为准)",
+      "dsva_requirement": "(同上)",
+      "severity": "BLOCKER",
+      "validation_method": "manual_review",
+      "requires_manual_review": true,
+      "is_deprecated": true,
+      "deprecated_reason": "1990版已废止（2005-10-14）；用户原写名称实为 GB/T 12467 系列",
+      "source_url": "https://std.samr.gov.cn/gb/search/gbDetailed?id=71F772D7809DD3A7E05397BE0A0AB82A",
+      "note": "用户反馈废止日期2005-10-14；功能相近的现行标准为GB/T 19418-2003《钢的弧焊接头 缺陷质量分级指南》"
+    },
+    {
+      "rule_id": "GB_STRUCTURAL-007",
+      "standard_id": "GB/T 3811-2008",
+      "title": "起重机设计规范",
+      "topic": "起重机械金属结构",
+      "scope": "本标准确立了起重机总体、结构、机械、电气与安全等部分设计应共同遵守的必要准则，规定了设计、计算要求和方法，并可作为对设计进行分析和评价的技术依据。本标准适用于桥架型起重机、臂架型起重机和缆索型起重机，但不涉及上述起重机设计的特殊问题。本标准也可供其他起重机参照使用。",
+      "status": "现行(代替GB/T 3811-1983)",
+      "dsva_requirement": "动载系数、疲劳、屈服、稳定、失效保护",
+      "severity": "BLOCKER",
+      "validation_method": "manual_review",
+      "requires_manual_review": true,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/std/newGbInfo?hcno=4F6CEE797EBFF2A3E3B96DC198AE18DA",
+      "note": ""
+    },
+    {
+      "rule_id": "GB_STRUCTURAL-008",
+      "standard_id": "GB/T 6067.1-2010",
+      "title": "起重机械安全规程 第1部分：总则",
+      "topic": "起重机械金属结构",
+      "scope": "GB 6067 的本部分规定了起重机械的设计、制造、安装、改造、维修、使用、报废、检查等方面的基本安全要求。本部分适用于桥式和门式起重机、流动式起重机、塔式起重机、臂架起重机、缆索起重机及轻小型起重设备的通用要求。对特定型式起重机械的特殊要求在 GB 6067 的其他部分中给出。本部分不适用于浮式起重机、甲板起重机及载人等起重设备。",
+      "status": "现行",
+      "dsva_requirement": "(同上)",
+      "severity": "BLOCKER",
+      "validation_method": "manual_review",
+      "requires_manual_review": true,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=9DED7058601D511BFD5EEE88677548D8",
+      "note": "原为强制性GB 6067.1-2010，依2017年第7号公告自2017-03-23强改推为推荐性GB/T；引用时宜注明"
+    },
+    {
+      "rule_id": "GB_STRUCTURAL-009",
+      "standard_id": "GB/T 14406-2011",
+      "title": "通用门式起重机",
+      "topic": "起重机械金属结构",
+      "scope": "本标准规定了额定起重量为3.2t~320t通用门式起重机的型式分类与基本参数、技术要求、试验方法、检验规则、标志、包装、运输及贮存。本标准适用于在露天作业的通用门式起重机（以下简称起重机）。其取物装置为吊钩或抓斗或起重电磁铁（电磁吸盘），或同时用其中二种或三种。",
+      "status": "现行",
+      "dsva_requirement": "(同上)",
+      "severity": "BLOCKER",
+      "validation_method": "manual_review",
+      "requires_manual_review": true,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=FDE4E0D761D3681F02936BE626320934",
+      "note": "修订计划20254756-T-604正在征求意见"
+    },
+    {
+      "rule_id": "GB_STRUCTURAL-010",
+      "standard_id": "GB/T 19418-2003",
+      "title": "钢的弧焊接头 缺陷质量分级指南",
+      "topic": "焊接接头缺欠质量分级",
+      "scope": "本标准规定了钢弧焊接头缺陷的质量等级。这些等级与产品的制造质量有关而与其适用性(见3.1)无关。本标准适用于:——按GB/T 5185规定的下述焊接方法及其工艺类别:11无气体保护的金属电弧焊;12埋弧焊;13气体保护电弧焊;14非熔化极气体保护电弧焊;15等离子弧焊;——手工、机械化及自动化焊接方法;——所有的焊接位置;——对接焊缝、角焊缝及支管接头;——厚度范围在3~63 mm的钢材。本标准未考虑冶金方面的因素,如:晶粒尺寸、硬度。",
+      "status": "现行",
+      "dsva_requirement": "承载焊缝质量等级、NDT验收",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=12D30DA26FA5F9418BED933A7B7430E6",
+      "note": "等同采用ISO 5817:1992(IDT)；修订计划20253463-T-469征求意见中，新版拟改名《钢、镍、钛及其合金的熔焊接头(束焊除外) 缺欠质量分级指南》"
+    },
+    {
+      "rule_id": "GB_STRUCTURAL-011",
+      "standard_id": "GB/T 26951-2025",
+      "title": "焊缝无损检测 磁粉检测",
+      "topic": "焊缝磁粉检测",
+      "scope": "本文件规定了铁磁性材料焊缝及热影响区表面缺欠的磁粉检测方法,该方法适用于大多数焊接工艺和接头结构。附录A描述了磁粉检测基本工艺中影响达到更高或更低检测灵敏度的因素。本文件不规定显示的验收等级。显示的验收等级的更多信息见ISO 23278或产品/应用标准。",
+      "status": "现行(代替GB/T 26951-2011)",
+      "dsva_requirement": "焊缝NDT比例与验收等级",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://std.samr.gov.cn/gb/search/gbDetailed?id=42BA7D06A3FCE936E06397BE0A0ACDC9",
+      "note": "等同采用ISO 17638:2016(IDT)；2026-02-01已实施"
+    },
+    {
+      "rule_id": "GB_STRUCTURAL-012",
+      "standard_id": "GB 50661-2011",
+      "title": "钢结构焊接规范",
+      "topic": "钢结构焊接规范",
+      "scope": "1.0.2 本规范适用于工业与民用钢结构工程中承受静荷载或动荷载、钢材厚度不小于3mm的结构焊接。本规范适用的焊接方法包括焊条电弧焊、气体保护电弧焊、药芯焊丝自保护焊、埋弧焊、电渣焊、气电立焊、栓钉焊及其组合。",
+      "status": "现行(强制性条文部分被GB 55006-2021替代)",
+      "dsva_requirement": "钢结构焊接规范",
+      "severity": "BLOCKER",
+      "validation_method": "manual_review",
+      "requires_manual_review": true,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://www.mohurd.gov.cn/gongkai/zc/wjk/art/2012/art_17339_208377.html",
+      "note": "工程建设国标(住建部公告第1212号)；强条4.0.1、5.7.1、6.1.1、8.1.8；新版《钢结构焊接标准》修订中，网上流传GB 50661-2024/2025均非官方"
+    }
+  ]
+}

package/engineering/tools/physics/rules/gb_surface_rules.json

@@ -0,0 +1,25 @@
+{
+  "ruleset_id": "DSVA-GB_SURFACE",
+  "revision": "A",
+  "category": "gb_surface",
+  "generated_from": "DSVA国标对照表.xlsx",
+  "total": 1,
+  "rules": [
+    {
+      "rule_id": "GB_SURFACE-001",
+      "standard_id": "GB/T 10125-2021",
+      "title": "人造气氛腐蚀试验 盐雾试验",
+      "topic": "中性盐雾试验/盐雾试验体系",
+      "scope": "本文件规定了中性盐雾(NSS)、乙酸盐雾(AASS)和铜加速乙酸盐雾(CASS)试验使用的设备、试剂和方法。本文件也规定了评估试验箱环境腐蚀性的方法。本文件适用于评价金属材料及覆盖层的耐蚀性,被测试对象可以是具有永久性或暂时性防蚀性能的,也可以是不具有永久性或暂时性防蚀性能的。本文件未规定试验试样尺寸和类型,特殊产品的试验周期和结果解释,这些内容参见相应的产品规范。本文件适用于检测金属及其合金、金属覆盖层、有机覆盖层、阳极氧化膜和转化膜的不连续性,如孔隙及其他缺陷。中性盐雾试验适用于:金属及其合金;金属覆盖层(阳极性或阴极性);转化膜;阳极氧化膜;金属基体上的有机覆盖层。乙酸盐雾试验适用于铜+镍+铬或镍+铬装饰性镀层,也适用于铝的阳极氧化膜和有机覆盖层。铜加速乙酸盐雾试验适用于铜+镍+铬或镍+铬装饰性镀层,也适用于铝的阳极氧化膜和有机覆盖层。这些方法都适用于金属材料具有或不具有腐蚀保护时的质量检查,不适用于对不同材料进行有耐蚀性的排序或预测试验材料的长期耐蚀性。",
+      "status": "现行(代替GB/T 10125-2012)",
+      "dsva_requirement": "盐雾试验时间或对应防腐等级",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=4C8B2824D589D76F0CFE7812D7434D22",
+      "note": "修改采用ISO 9227:2017(MOD)"
+    }
+  ]
+}

package/engineering/tools/physics/rules/gb_transmission_rules.json

@@ -0,0 +1,233 @@
+{
+  "ruleset_id": "DSVA-GB_TRANSMISSION",
+  "revision": "A",
+  "category": "gb_transmission",
+  "generated_from": "DSVA国标对照表.xlsx",
+  "total": 14,
+  "rules": [
+    {
+      "rule_id": "GB_TRANSMISSION-001",
+      "standard_id": "GB/T 15753-1995",
+      "title": "圆弧圆柱齿轮精度",
+      "topic": "机械传动基础",
+      "scope": "本标准规定了圆弧圆柱齿轮及其齿轮副的误差定义、代号、精度等级、齿坯要求、齿轮及其齿轮副的检验与公差、侧隙、图样标注及应注明的尺寸数据。本标准适用于平行轴传动的圆弧圆柱齿轮及其齿轮副。齿轮的基本齿廓符合 GB 12759-91 的规定，法向模数等于 1.5~40 mm。",
+      "status": "现行(2023-12-28复审继续有效)",
+      "dsva_requirement": "功率、转速、扭矩、载荷系数、寿命",
+      "severity": "BLOCKER",
+      "validation_method": "manual_review",
+      "requires_manual_review": true,
+      "is_deprecated": true,
+      "deprecated_reason": "1995版实际是圆弧圆柱齿轮精度，不是原文写的圆柱齿轮精度；直齿/斜齿应见 GB/T 10095",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/std/newGbInfo?hcno=A8B8AB05137EC403630472CB3DC680EA",
+      "note": "名称即“圆弧圆柱齿轮精度”(非普通圆柱齿轮精度)；代替JB 4021-1985；直齿/斜齿圆柱齿轮精度看GB/T 10095"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-002",
+      "standard_id": "GB/T 3478.1-2008",
+      "title": "圆柱直齿渐开线花键(米制模数 齿侧配合) 第1部分：总论",
+      "topic": "花键",
+      "scope": "GB/T 3478 的本部分规定了圆柱直齿渐开线花键的模数系列、基本齿廓、公差和齿侧配合类别等内容。本部分适用于标准压力角为 30°和 37.5°（模数从 0.5 mm~10 mm）以及 45°（模数从 0.25 mm~2.5 mm）齿侧配合的圆柱直齿渐开线花键。",
+      "status": "现行(代替GB/T 3478.1-1995)",
+      "dsva_requirement": "模数、齿数、配合、公差、承载能力",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=23679C5B92039BE3D1CAC906086A2CB3",
+      "note": "GB/T 3478为9部分系列，取第1部分总论"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-003",
+      "standard_id": "GB/T 1357-2008",
+      "title": "通用机械和重型机械用圆柱齿轮 模数",
+      "topic": "圆柱齿轮",
+      "scope": "本标准规定了通用机械和重型机械用直齿和斜齿渐开线圆柱齿轮的法向模数。本标准不适用于汽车齿轮。",
+      "status": "现行(代替GB/T 1357-1987)",
+      "dsva_requirement": "标准模数、精度等级、齿轮强度、齿侧间隙",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=6F4F435FC3E486E00DC85E7697A842DB",
+      "note": "采标ISO 54:1996(IDT)"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-004",
+      "standard_id": "GB/T 10095.1-2022；GB/T 10095.2-2023",
+      "title": "圆柱齿轮 ISO齿面公差分级制 第1部分:齿面偏差的定义和允许值；第2部分:径向综合偏差的定义和允许值",
+      "topic": "圆柱齿轮",
+      "scope": "【.1-2022】本文件规定了单个渐开线圆柱齿轮齿面的制造和合格判定的公差分级制，还规定了各项齿面公差的术语、齿面公差分级制的结构和允许值。按照公差值由小到大的顺序，定义了 11 个齿面公差等级，从 1 级到 11 级。【.2-2023】本文件确立了单个渐开线圆柱齿轮及扇形齿轮的径向综合偏差的公差分级制，规定了径向综合偏差的定义、公差分级制的结构和偏差允许值。本文件适用于齿数不小于 3、分度圆直径不大于 600 mm 的齿轮。",
+      "status": "均现行",
+      "dsva_requirement": "(同上)",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=878B6293F0696ECAC9481EC46DBF279C ；https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=9385560A2DF63657F88A12730DAF1AA2",
+      "note": "更正：GB/T 10095.2-2022不存在，正确为GB/T 10095.2-2023(2023-08-06发布/2024-03-01实施)；等同采用ISO 1328-1:2013、ISO 1328-2:2020"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-005",
+      "standard_id": "GB/T 3480.1-2019(系列)",
+      "title": "直齿轮和斜齿轮承载能力计算 第1部分：基本原理、概述及通用影响系数",
+      "topic": "圆柱齿轮",
+      "scope": "GB/T 3480 的本部分介绍了直齿轮与斜齿轮承载能力计算的基本原理、概述及通用影响系数。它与 ISO 6336-2、ISO 6336-3、ISO 6336-5 及 ISO 6336-6 一起提供了一种可以对不同的齿轮设计进行比较的方法。GB/T 3480 中的公式是为了给渐开线圆柱直齿轮或斜齿轮的齿面接触强度和齿根弯曲强度计算提供一个广泛接受的方法而提出的。GB/T 3480 中的公式不适用于端面重合度小于 1.0 或大于 2.5、齿顶与齿根干涉、尖顶齿、侧隙为 0 以及胶合、磨损、塑性屈服等损伤情况。",
+      "status": "现行(代替GB/T 3480-1997)",
+      "dsva_requirement": "齿轮强度、齿侧间隙",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/std/newGbInfo?hcno=CEBC81CF1C6DEB9831444DAC7CEADB11",
+      "note": "等同采用ISO 6336-1:2006(IDT)；系列另含GB/Z 3480.20/21-2025(胶合)、GB/Z 3480.22-2024(微点蚀)、GB/Z 3480.31-2025(算例)等"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-006",
+      "standard_id": "GB/T 11365-2019",
+      "title": "锥齿轮 精度制",
+      "topic": "锥齿轮",
+      "scope": "本标准规定了未装配的锥齿轮、准双曲面齿轮及其组件的精度术语、等级与公差值。即规定了齿形精度的术语、等级体系结构和允许值。本标准为供需双方提供了统一的公差尺度，定义了 10 个精度等级，从 2 级到 11 级。本标准推荐的测量方法见第 6 章。本标准不适用于减速器、增速器、齿轮马达、轴装式减速器、高速传动及其他按给定功率、速度、传动比或应用环境而制造的封闭式齿轮装置。",
+      "status": "现行(代替GB/T 11365-1989)",
+      "dsva_requirement": "啮合参数、精度、接触区、强度",
+      "severity": "BLOCKER",
+      "validation_method": "manual_review",
+      "requires_manual_review": true,
+      "is_deprecated": true,
+      "deprecated_reason": "1989版旧名已变更为\"锥齿轮 精度制\"",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=B3F3DE556314D8165993AFD1EFE20208",
+      "note": "名称已由“锥齿轮和准双曲面齿轮 精度”变更为“锥齿轮 精度制”；代替GB/T 11365-1989；等同采用ISO 17485:2006"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-007",
+      "standard_id": "GB/T 10085-2018",
+      "title": "圆柱蜗杆传动基本参数",
+      "topic": "蜗杆传动",
+      "scope": "本标准规定了圆柱蜗杆传动基本参数。本标准适用于模数 m≥1 mm、轴交角 Σ=90° 的圆柱蜗杆传动。",
+      "status": "现行(代替GB/T 10085-1988)",
+      "dsva_requirement": "模数、导程角、效率、热平衡、齿面强度",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=F348AFC9E7ADAA4A3A6CC1705F329961",
+      "note": "修订计划20251456-T-469《圆柱蜗杆、蜗轮 基本参数》正在批准，新版名称将变更"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-008",
+      "standard_id": "GB/T 1356-2001",
+      "title": "通用机械和重型机械用圆柱齿轮 标准基本齿条齿廓",
+      "topic": "渐开线圆柱齿轮基本齿廓",
+      "scope": "本标准规定了通用机械和重型机械用渐开线圆柱齿轮(外齿或内齿)的标准基本齿条齿廓的几何参数。本标准适用于GB/T1357规定的标准模数。本标准规定的齿廓没有考虑内齿轮齿高可能进行的修正,内齿轮对不同的情况应分别计算。为了确定渐开线类齿轮的轮齿尺寸,在本标准中,标准基本齿条的齿廓仅给出了渐开线类齿轮齿廓的几何参数。它不包括对刀具的定义.但为了获得合适的齿廓,可以根据本标准基本齿条的齿廓规定刀具的参数。",
+      "status": "现行(2023-12-28复审继续有效)",
+      "dsva_requirement": "齿轮基本齿廓、模数",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=7D44A15888B2E686063491408AB63CC8",
+      "note": "等同采用ISO 53:1998"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-009",
+      "standard_id": "GB/T 119.1-2000",
+      "title": "圆柱销 不淬硬钢和奥氏体不锈钢",
+      "topic": "圆柱销",
+      "scope": "本标准规定了公称直径d=0.6~50 mm、公差为m6和h8、材料为不淬硬钢和奥氏体不锈钢的圆柱销。",
+      "status": "现行(部分代替GB/T 119-1986)",
+      "dsva_requirement": "定位销过渡或轻过盈配合",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=A232516C9A38BDB5380B71213BD276C5",
+      "note": "等效采用ISO 2338:1997"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-010",
+      "standard_id": "GB/T 117-2000",
+      "title": "圆锥销",
+      "topic": "圆锥销",
+      "scope": "本标准规定了公称直径d=0.6~50mm、A型和B型的圆锥销。",
+      "status": "现行(全部代替GB/T 117-1986)",
+      "dsva_requirement": "圆锥销受力、拆装",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=D90C7EEE19C6BF1AA28F6FB6BBA4F8E3",
+      "note": "等效采用ISO 2339:1986"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-011",
+      "standard_id": "GB/T 91-2000",
+      "title": "开口销",
+      "topic": "开口销",
+      "scope": "本标准规定了公称规格为0.6~20mm的开口销。",
+      "status": "现行(全部代替GB/T 91-1986)",
+      "dsva_requirement": "防松、轴端固定",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://ndls.cnis.ac.cn/standard/detail/2fa6ad75c5e83a4ac01393da11e64bd6",
+      "note": "等效采用ISO 1234:1997"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-012",
+      "standard_id": "GB/T 4604.1-2012",
+      "title": "滚动轴承 游隙 第1部分：向心轴承的径向游隙",
+      "topic": "滚动轴承游隙",
+      "scope": "GB/T 4604的本部分规定了下列类型向心轴承的径向游隙值: --径向接触沟型球轴承,外球面球轴承除外; --调心球轴承; --圆柱滚子轴承; --滚针轴承,冲压外圈滚针轴承除外; --长弧面滚子轴承; --调心滚子轴承。 本部分给出了六种类型圆柱孔轴承的径向游隙值,也给出了圆锥孔调心球轴承、圆柱滚子轴承、长弧面滚子轴承和调心滚子轴承的径向游隙值。 外球面球轴承的径向游隙值规定在ISO 9628中",
+      "status": "现行(全部代替GB/T 4604-2006)",
+      "dsva_requirement": "轴承游隙选型(高温高速不能用默认游隙)",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/std/newGbInfo?hcno=A80E1B173DD5083779747969ADD74FEC",
+      "note": "系列含.2轴向游隙;等同ISO 5753-1:2009"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-013",
+      "standard_id": "GB/T 1243-2024",
+      "title": "传动用短节距精密滚子链、套筒链、附件和链轮",
+      "topic": "短节距传动用精密滚子链",
+      "scope": "本文件规定了适合于机械传动和类似应用的短节距精密滚子链和套筒链以及链轮的技术要求,包括尺寸、公差、长度测量、预拉、最小抗拉强度和最小动载强度。 尽管第5章适用于自行车和摩托车的链轮,但本文件不适用于自行车和摩托车的链条,自行车和摩托车链条标准分别规定于ISO 9633和ISO 10190。",
+      "status": "现行(全部代替GB/T 1243-2006)",
+      "dsva_requirement": "链轮齿数、链速、中心距、张紧、润滑、防护罩",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/gb/newGbInfo?hcno=840F6F7405A9CC5D8968B2E2F04DF0E2",
+      "note": "等同采用ISO 606:2015"
+    },
+    {
+      "rule_id": "GB_TRANSMISSION-014",
+      "standard_id": "GB/T 20118-2025",
+      "title": "钢丝绳通用技术条件",
+      "topic": "钢丝绳",
+      "scope": "本文件界定了钢丝绳的术语和定义,给出了分类、标记,规定了订货内容、材料、技术要求、检验、验收方法、包装、标志及质量证明书、安全、使用和维护,描述了试验方法。 本文件适用于光面和镀层碳素钢丝制造的圆股和异形股钢丝绳。",
+      "status": "现行(全部代替GB/T 20118-2017、GB/T 25833-2010、GB/T 20067-2017)",
+      "dsva_requirement": "钢丝绳直径、破断拉力、安全系数、报废准则",
+      "severity": "INFO",
+      "validation_method": "drawing_check",
+      "requires_manual_review": false,
+      "is_deprecated": false,
+      "deprecated_reason": "",
+      "source_url": "https://openstd.samr.gov.cn/bzgk/std/newGbInfo?hcno=B22A70CD13C27D76E425B88967C3B33C",
+      "note": "修改采用ISO 2408:2017；合并GB/T 20118-2017、GB/T 25833-2010、GB/T 20067-2017三项标准"
+    }
+  ]
+}

package/engineering/tools/physics/rules/housing_rules.json

@@ -0,0 +1,48 @@
+{
+  "domain_id": "housing",
+  "domain_name": "壳体",
+  "version": "1.0",
+  "description": "箱体/盖板/外壳类壳体件的设计规范",
+  "rules": [
+    {
+      "id": "HS-001",
+      "type": "parametric",
+      "target": "wall_thickness_mm",
+      "condition": {"min": 2.0, "max": 30.0},
+      "severity": "CRITICAL",
+      "message": "壳体壁厚应在 2~30mm 之间"
+    },
+    {
+      "id": "HS-002",
+      "type": "parametric",
+      "target": "rib_height_mm",
+      "condition": {"min": 0, "max": 50.0},
+      "severity": "INFO",
+      "message": "加强筋高度 ≤ 50mm，避免铸造缺陷"
+    },
+    {
+      "id": "HS-003",
+      "type": "fea",
+      "target": "max_von_mises_mpa",
+      "condition": {"max": 150.0},
+      "severity": "WARNING",
+      "message": "壳体等效应力 ≤ 150MPa（防止变形失效）"
+    },
+    {
+      "id": "HS-004",
+      "type": "fea",
+      "target": "max_displacement_mm",
+      "condition": {"max": 1.0},
+      "severity": "CRITICAL",
+      "message": "壳体最大变形 ≤ 1.0mm（保证密封/装配）"
+    },
+    {
+      "id": "HS-005",
+      "type": "fea",
+      "target": "mass_kg",
+      "condition": {"max": 100.0},
+      "severity": "INFO",
+      "message": "壳体质量建议 < 100kg（便于装配与运输）"
+    }
+  ]
+}

package/engineering/tools/physics/rules/manifest.json

@@ -0,0 +1,54 @@
+{
+  "ruleset_id": "DSVA-GB",
+  "revision": "A",
+  "generated_from": "DSVA国标对照表.xlsx",
+  "enabled_packs": [
+    "gb_standards_registry.json",
+    "gb_base_rules.json",
+    "gb_materials_rules.json",
+    "gb_structural_rules.json",
+    "gb_transmission_rules.json",
+    "gb_housing_rules.json",
+    "gb_drafting_rules.json",
+    "gb_electrical_rules.json",
+    "gb_fasteners_rules.json",
+    "gb_springs_rules.json",
+    "gb_manufacturing_rules.json",
+    "gb_surface_rules.json",
+    "gb_safety_rules.json"
+  ],
+  "deprecated_standards": {
+    "GB/T 3323": "原单号已废止，拆分为 GB/T 3323.1-2019、GB/T 3323.2-2019",
+    "GB/T 12469": "1990版已废止（2005-10-14）；用户原写名称实为 GB/T 12467 系列",
+    "GB/T 15753": "1995版实际是圆弧圆柱齿轮精度，不是原文写的圆柱齿轮精度；直齿/斜齿应见 GB/T 10095",
+    "GB/T 16923": "2008版将被 GB/T 16923-2026 代替（2027-02-01起）",
+    "GB/T 11365": "1989版旧名已变更为\"锥齿轮 精度制\"",
+    "GB/T 42124.3-2025": "部分平台标注 GB/T 6414 被代替，存分歧；DSVA 暂保留 GB/T 6414-2017"
+  },
+  "manual_review_required": [
+    "GB/T 5226.1",
+    "GB/T 15706",
+    "GB/T 16754",
+    "GB 50017",
+    "GB 6067.1",
+    "GB 50661",
+    "GB/T 16855.1",
+    "GB/T 23821",
+    "GB/T 16855",
+    "GB/T 3811",
+    "GB 2894",
+    "GB/T 14406",
+    "GB/T 6067.1"
+  ],
+  "notes": [
+    "本规则集为元数据注册表与适用性提示；具体机读数值表须另行从标准原文提取。",
+    "BLOCKER/CRITICAL 类规则必须经人工复核，不可由 AI 自动放行。",
+    "deprecated 项已保留但需在使用前确认现行版本。"
+  ],
+  "source_metadata": {
+    "xlsx_path": "C:\\Users\\j1877\\WorkBuddy\\2026-08-26-15-05-33\\DSVA国标对照表.xlsx",
+    "rows_imported": 91,
+    "deprecated_count": 9,
+    "manual_review_count": 11
+  }
+}

package/engineering/tools/physics/rules/mold_rules.json

@@ -0,0 +1,48 @@
+{
+  "domain_id": "mold",
+  "domain_name": "模具",
+  "version": "1.0",
+  "description": "型腔/型芯/镶件等模具零件的设计规范",
+  "rules": [
+    {
+      "id": "MD-001",
+      "type": "parametric",
+      "target": "cavity_depth_mm",
+      "condition": {"min": 0.1, "max": 200.0},
+      "severity": "CRITICAL",
+      "message": "型腔深度应在 0.1~200mm 之间"
+    },
+    {
+      "id": "MD-002",
+      "type": "parametric",
+      "target": "draft_angle_deg",
+      "condition": {"min": 0.5, "max": 5.0},
+      "severity": "CRITICAL",
+      "message": "脱模斜度应在 0.5°~5° 之间（避免脱模卡死）"
+    },
+    {
+      "id": "MD-003",
+      "type": "fea",
+      "target": "max_von_mises_mpa",
+      "condition": {"max": 800.0},
+      "severity": "WARNING",
+      "message": "模具钢（HRC 50+）允许应力 ≤ 800MPa"
+    },
+    {
+      "id": "MD-004",
+      "type": "fea",
+      "target": "max_displacement_mm",
+      "condition": {"max": 0.05},
+      "severity": "CRITICAL",
+      "message": "模具型腔变形 ≤ 0.05mm（保证制品精度）"
+    },
+    {
+      "id": "MD-005",
+      "type": "parametric",
+      "target": "surface_roughness_um",
+      "condition": {"min": 0.025, "max": 6.3},
+      "severity": "INFO",
+      "message": "型腔表面粗糙度应在 0.025~6.3μm 之间"
+    }
+  ]
+}