biscuitboard 1.0.5 → 1.0.7

package/README.md

@@ -217,11 +217,13 @@ upper-right clad hole clears the D0-D7 header. Relative placement remains
 official UNO R3 geometry for the 1x8 power header, 1x6 analog header, 1x8
 D0-D7 header, 1x10 R3 digital/AREF/I2C header, and 2x3 ICSP socket.
 
-The 262 assignable fixed vias use 0.3 mm drills, 0.6 mm copper pads, and 1.3 mm
-center-to-center pitch. The clustered layout has upper- and lower-left edge
-fields, two inset left fields, a central routing field spanning -19 to -3 mm,
-and split right-edge rails. The area immediately left of ICSP, the header rows, and
-the original clad mounting holes remain open. The bare template and its
+The 226 assignable fixed vias use 0.3 mm drills, 0.6 mm copper pads, and 1.3 mm
+center-to-center pitch. A 130-via central routing field spanning -19 to -3 mm
+is retained. Three corners use compact three-via-wide L-shaped fields; the
+upper-right uses one three-row horizontal arm parallel to its two mounting
+holes and lowered around the crowded UNO header region. The area immediately
+left of ICSP, the header rows, and the original clad mounting holes remain
+open. The bare template and its
 checked-in PCB snapshot are in
 [`examples/arduino-shield-clad.tsx`](./examples/arduino-shield-clad.tsx).
 
@@ -308,18 +310,17 @@ bun test tests/feather-clad.test.tsx
 [`BreadboardClad`](./lib/breadboard-clad.tsx) is a laser-routable 75 mm x
 55 mm plug-in prototyping board. It provides 210 individually routable female
 header sockets labeled A1 through J21, with the standard 2.54 mm terminal pitch
-and a 7.62 mm DIP channel. Four 21-pin power/header rails run along the top and
-bottom. Unlike a solderless breadboard, none of these sockets are connected in
-groups: the consuming tscircuit design defines every connection, allowing the
-corresponding copper traces to be laser cut for a particular circuit.
-
-The 162 assignable prefabricated vias have 0.3 mm holes and 0.6 mm pads. A
-single 21-via row sits between each power-header pair and its neighboring
-terminal field, while two 21-via rows run through the central DIP channel. A
-single-via-wide outer field runs beyond the headers on all four sides. The
-socket grids themselves remain clear.
-`BreadboardTerminalHeaders` exposes terminal aliases such as `A1` and `J21`;
-`BreadboardPowerHeader` exposes `COL1` through `COL21`. The bare preview is in
+and a 7.62 mm DIP channel. Unlike a solderless breadboard, none of these
+sockets are connected in groups: the consuming tscircuit design defines every
+connection, allowing the corresponding copper traces to be laser cut for a
+particular circuit.
+
+The 148 assignable prefabricated vias have 0.3 mm holes and 0.6 mm pads. Two
+21-via rows sit beyond the terminal fields, two 21-via rows run through the
+central DIP channel, and four two-via-wide L-shaped corner fields provide 64
+additional vias. The socket grid remains clear.
+`BreadboardTerminalHeaders` exposes terminal aliases such as `A1` and `J21`.
+The bare preview is in
 [`examples/breadboard-clad.tsx`](./examples/breadboard-clad.tsx).
 
 ```sh

package/dist/npm.cjs

@@ -785,15 +785,18 @@ __export(npm_exports, {
   BREADBOARD_CLAD_WIDTH: () => BREADBOARD_CLAD_WIDTH,
   BREADBOARD_COLUMN_COUNT: () => BREADBOARD_COLUMN_COUNT,
   BREADBOARD_COLUMN_XS: () => BREADBOARD_COLUMN_XS,
+  BREADBOARD_CORNER_VIA_ARM_WIDTH: () => BREADBOARD_CORNER_VIA_ARM_WIDTH,
+  BREADBOARD_CORNER_VIA_POSITIONS: () => BREADBOARD_CORNER_VIA_POSITIONS,
+  BREADBOARD_CORNER_VIA_SPACING: () => BREADBOARD_CORNER_VIA_SPACING,
+  BREADBOARD_CORNER_VIA_X_INNER_OFFSET: () => BREADBOARD_CORNER_VIA_X_INNER_OFFSET,
+  BREADBOARD_CORNER_VIA_X_OUTER_OFFSET: () => BREADBOARD_CORNER_VIA_X_OUTER_OFFSET,
+  BREADBOARD_CORNER_VIA_X_OUTWARD_SHIFT: () => BREADBOARD_CORNER_VIA_X_OUTWARD_SHIFT,
+  BREADBOARD_CORNER_VIA_Y_INNER_OFFSET: () => BREADBOARD_CORNER_VIA_Y_INNER_OFFSET,
+  BREADBOARD_CORNER_VIA_Y_OUTER_OFFSET: () => BREADBOARD_CORNER_VIA_Y_OUTER_OFFSET,
   BREADBOARD_HEADER_HOLE_DIAMETER: () => BREADBOARD_HEADER_HOLE_DIAMETER,
   BREADBOARD_HEADER_PAD_DIAMETER: () => BREADBOARD_HEADER_PAD_DIAMETER,
   BREADBOARD_HEADER_PITCH: () => BREADBOARD_HEADER_PITCH,
   BREADBOARD_MOUNTING_HOLE_DIAMETER: () => BREADBOARD_MOUNTING_HOLE_DIAMETER,
-  BREADBOARD_OUTER_VERTICAL_VIA_YS: () => BREADBOARD_OUTER_VERTICAL_VIA_YS,
-  BREADBOARD_OUTER_VIA_COLUMN_XS: () => BREADBOARD_OUTER_VIA_COLUMN_XS,
-  BREADBOARD_OUTER_VIA_ROW_YS: () => BREADBOARD_OUTER_VIA_ROW_YS,
-  BREADBOARD_POWER_HEADER_POSITIONS: () => BREADBOARD_POWER_HEADER_POSITIONS,
-  BREADBOARD_POWER_RAILS: () => BREADBOARD_POWER_RAILS,
   BREADBOARD_TERMINAL_HEADER_POSITIONS: () => BREADBOARD_TERMINAL_HEADER_POSITIONS,
   BREADBOARD_TERMINAL_ROW_LABELS: () => BREADBOARD_TERMINAL_ROW_LABELS,
   BREADBOARD_TERMINAL_ROW_YS: () => BREADBOARD_TERMINAL_ROW_YS,
@@ -803,7 +806,6 @@ __export(npm_exports, {
   BoosterPackLeftHeader: () => BoosterPackLeftHeader,
   BoosterPackRightHeader: () => BoosterPackRightHeader,
   BreadboardClad: () => BreadboardClad,
-  BreadboardPowerHeader: () => BreadboardPowerHeader,
   BreadboardTerminalHeaders: () => BreadboardTerminalHeaders,
   CLAD_40X40_EDGE_MOUNTING_HOLE_INSET: () => CLAD_40X40_EDGE_MOUNTING_HOLE_INSET,
   CLAD_40X40_HEIGHT: () => CLAD_40X40_HEIGHT,
@@ -14524,41 +14526,46 @@ var ARDUINO_SHIELD_CLAD_VIA_SPACING = 1.3;
 var ARDUINO_SHIELD_EDGE_CLEARANCE = 0.2;
 var ARDUINO_SHIELD_EDGE_CLEARANCE_VALIDATION_TOLERANCE = 1e-3;
 var rangeInclusive = (start, end, increment) => Array.from(
-  { length: Math.max(0, Math.floor((end - start) / increment) + 1) },
+  {
+    length: Math.max(0, Math.floor((end - start) / increment + 1e-9) + 1)
+  },
   (_, index) => Math.round((start + index * increment) * 1e6) / 1e6
 );
 var createViaZone2 = (zone) => rangeInclusive(zone.minX, zone.maxX, zone.spacing).flatMap(
   (x) => rangeInclusive(zone.minY, zone.maxY, zone.spacing).map((y) => ({ x, y }))
 );
 var ARDUINO_SHIELD_CLAD_VIA_CANDIDATE_ZONES = [
+  // Upper-left horizontal and vertical arms.
   {
-    minX: -33.5,
-    maxX: -25.5,
-    minY: 17.5,
-    maxY: 21.5,
+    minX: -36.1,
+    maxX: -29.6,
+    minY: 19.7,
+    maxY: 22.3,
     spacing: ARDUINO_SHIELD_CLAD_VIA_SPACING
   },
   {
-    minX: -33.5,
-    maxX: -25.5,
-    minY: -21.5,
-    maxY: -17.5,
+    minX: -32.2,
+    maxX: -29.6,
+    minY: 19.7,
+    maxY: 26.2,
     spacing: ARDUINO_SHIELD_CLAD_VIA_SPACING
   },
+  // Lower-left horizontal and vertical arms.
   {
-    minX: -21.5,
-    maxX: -13.5,
-    minY: 13.5,
-    maxY: 17.5,
+    minX: -36.1,
+    maxX: -29.6,
+    minY: -22.3,
+    maxY: -19.7,
     spacing: ARDUINO_SHIELD_CLAD_VIA_SPACING
   },
   {
-    minX: -21.5,
-    maxX: -13.5,
-    minY: -17.5,
-    maxY: -13.5,
+    minX: -32.2,
+    maxX: -29.6,
+    minY: -26.2,
+    maxY: -19.7,
     spacing: ARDUINO_SHIELD_CLAD_VIA_SPACING
   },
+  // Preserve the large central routing field exactly.
   {
     minX: -19,
     maxX: -3,
@@ -14566,18 +14573,27 @@ var ARDUINO_SHIELD_CLAD_VIA_CANDIDATE_ZONES = [
     maxY: 6,
     spacing: ARDUINO_SHIELD_CLAD_VIA_SPACING
   },
+  // Upper-right horizontal arm, parallel to the two mounting holes.
   {
-    minX: 34.5,
-    maxX: 34.5,
-    minY: -19.5,
-    maxY: -7.5,
+    minX: 30.9,
+    maxX: 36.1,
+    minY: 19.7,
+    maxY: 22.3,
     spacing: ARDUINO_SHIELD_CLAD_VIA_SPACING
   },
+  // Lower-right horizontal and vertical arms.
   {
-    minX: 34.5,
-    maxX: 34.5,
-    minY: 7.5,
-    maxY: 19.5,
+    minX: 29.6,
+    maxX: 36.1,
+    minY: -22.3,
+    maxY: -19.7,
+    spacing: ARDUINO_SHIELD_CLAD_VIA_SPACING
+  },
+  {
+    minX: 29.6,
+    maxX: 32.2,
+    minY: -26.2,
+    maxY: -19.7,
     spacing: ARDUINO_SHIELD_CLAD_VIA_SPACING
   }
 ];
@@ -14894,17 +14910,23 @@ var ArduinoShieldClad = ({
           fontSize: "0.6mm"
         }
       ),
-      ARDUINO_SHIELD_CLAD_VIA_CANDIDATE_ZONES.map((zone) => /* @__PURE__ */ (0, import_jsx_runtime2.jsx)(import_react2.Fragment, { children: /* @__PURE__ */ (0, import_jsx_runtime2.jsx)(
-        "pcbnoterect",
+      ARDUINO_SHIELD_CLAD_VIA_CANDIDATE_ZONES.map((zone) => /* @__PURE__ */ (0, import_jsx_runtime2.jsx)(
+        import_react2.Fragment,
         {
-          color: "blue",
-          width: Math.max(0.2, zone.maxX - zone.minX),
-          height: Math.max(0.2, zone.maxY - zone.minY),
-          pcbPositionAnchor: "center",
-          pcbX: zone.minX + (zone.maxX - zone.minX) / 2,
-          pcbY: zone.minY + (zone.maxY - zone.minY) / 2
-        }
-      ) }, `arduino-via-zone-${zone.minX}-${zone.minY}`)),
+          children: /* @__PURE__ */ (0, import_jsx_runtime2.jsx)(
+            "pcbnoterect",
+            {
+              color: "blue",
+              width: Math.max(0.2, zone.maxX - zone.minX),
+              height: Math.max(0.2, zone.maxY - zone.minY),
+              pcbPositionAnchor: "center",
+              pcbX: zone.minX + (zone.maxX - zone.minX) / 2,
+              pcbY: zone.minY + (zone.maxY - zone.minY) / 2
+            }
+          )
+        },
+        `arduino-via-zone-${zone.minX}-${zone.maxX}-${zone.minY}-${zone.maxY}`
+      )),
       ARDUINO_SHIELD_CLAD_VIA_POSITIONS.map((via) => /* @__PURE__ */ (0, import_jsx_runtime2.jsx)(import_react2.Fragment, { children: /* @__PURE__ */ (0, import_jsx_runtime2.jsx)(
         "via",
         {
@@ -15587,8 +15609,13 @@ var BREADBOARD_CLAD_VIA_ROW_YS = [
   BREADBOARD_HEADER_PITCH / 2,
   16.51
 ];
-var BREADBOARD_OUTER_VIA_ROW_YS = [-24.13, 24.13];
-var BREADBOARD_OUTER_VIA_COLUMN_XS = [-27.94, 27.94];
+var BREADBOARD_CORNER_VIA_SPACING = 1.3;
+var BREADBOARD_CORNER_VIA_ARM_WIDTH = 1.3;
+var BREADBOARD_CORNER_VIA_X_INNER_OFFSET = 27;
+var BREADBOARD_CORNER_VIA_X_OUTER_OFFSET = 32.2;
+var BREADBOARD_CORNER_VIA_Y_INNER_OFFSET = 21;
+var BREADBOARD_CORNER_VIA_Y_OUTER_OFFSET = 26.2;
+var BREADBOARD_CORNER_VIA_X_OUTWARD_SHIFT = 3.9;
 var BREADBOARD_MOUNTING_HOLE_DIAMETER = 2.2;
 var BREADBOARD_CLAD_EDGE_CLEARANCE = 0.2;
 var BREADBOARD_CLAD_EDGE_CLEARANCE_VALIDATION_TOLERANCE = 1e-3;
@@ -15606,16 +15633,18 @@ var BREADBOARD_TERMINAL_ROW_LABELS = [
   "J"
 ];
 var roundCoordinate3 = (value) => Math.round(value * 1e6) / 1e6;
+var createPitchedRange = (start, end) => Array.from(
+  {
+    length: Math.round((end - start) / BREADBOARD_CORNER_VIA_SPACING) + 1
+  },
+  (_, index) => roundCoordinate3(start + index * BREADBOARD_CORNER_VIA_SPACING)
+);
 var BREADBOARD_COLUMN_XS = Array.from(
   { length: BREADBOARD_COLUMN_COUNT },
   (_, index) => roundCoordinate3(
     (index - (BREADBOARD_COLUMN_COUNT - 1) / 2) * BREADBOARD_HEADER_PITCH
   )
 );
-var BREADBOARD_OUTER_VERTICAL_VIA_YS = Array.from(
-  { length: 18 },
-  (_, index) => roundCoordinate3(-21.59 + index * BREADBOARD_CLAD_VIA_PITCH)
-);
 var BREADBOARD_TERMINAL_ROW_YS = Object.fromEntries(
   BREADBOARD_TERMINAL_ROW_LABELS.map((label, index) => {
     const bankIndex = index < 5 ? index : index - 5;
@@ -15632,32 +15661,61 @@ var BREADBOARD_TERMINAL_HEADER_POSITIONS = BREADBOARD_TERMINAL_ROW_LABELS.flatMa
     y: BREADBOARD_TERMINAL_ROW_YS[row]
   }))
 );
-var BREADBOARD_POWER_RAILS = [
-  { id: "topPositive", label: "+", y: 21.59 },
-  { id: "topNegative", label: "-", y: 19.05 },
-  { id: "bottomPositive", label: "+", y: -19.05 },
-  { id: "bottomNegative", label: "-", y: -21.59 }
-];
-var BREADBOARD_POWER_HEADER_POSITIONS = BREADBOARD_POWER_RAILS.flatMap(
-  (rail) => BREADBOARD_COLUMN_XS.map((x, columnIndex) => ({
-    rail: rail.id,
-    pin: columnIndex + 1,
-    label: `${rail.id}${columnIndex + 1}`,
-    column: columnIndex + 1,
-    x,
-    y: rail.y
-  }))
+var cornerViaAxisX = createPitchedRange(
+  BREADBOARD_CORNER_VIA_X_INNER_OFFSET,
+  BREADBOARD_CORNER_VIA_X_OUTER_OFFSET
+);
+var cornerViaAxisY = createPitchedRange(
+  BREADBOARD_CORNER_VIA_Y_INNER_OFFSET,
+  BREADBOARD_CORNER_VIA_Y_OUTER_OFFSET
+);
+var cornerViaArmAxisX = createPitchedRange(
+  BREADBOARD_CORNER_VIA_X_INNER_OFFSET,
+  BREADBOARD_CORNER_VIA_X_INNER_OFFSET + BREADBOARD_CORNER_VIA_ARM_WIDTH
+);
+var cornerViaArmAxisY = createPitchedRange(
+  BREADBOARD_CORNER_VIA_Y_INNER_OFFSET,
+  BREADBOARD_CORNER_VIA_Y_INNER_OFFSET + BREADBOARD_CORNER_VIA_ARM_WIDTH
+);
+var createCornerViaPositions = (xSign, ySign, xOutwardShift = 0) => {
+  const shiftedCornerViaAxisX = cornerViaAxisX.map(
+    (x) => roundCoordinate3(x + xOutwardShift)
+  );
+  const shiftedCornerViaArmAxisX = cornerViaArmAxisX.map(
+    (x) => roundCoordinate3(x + xOutwardShift)
+  );
+  const horizontalArm = shiftedCornerViaAxisX.flatMap(
+    (x) => cornerViaArmAxisY.map((y) => ({ x: x * xSign, y: y * ySign }))
+  );
+  const verticalArm = shiftedCornerViaArmAxisX.flatMap(
+    (x) => cornerViaAxisY.map((y) => ({ x: x * xSign, y: y * ySign }))
+  );
+  return Array.from(
+    new Map(
+      [...horizontalArm, ...verticalArm].map((point) => [
+        `${point.x},${point.y}`,
+        point
+      ])
+    ).values()
+  );
+};
+var BREADBOARD_CORNER_VIA_POSITIONS = [
+  [-1, -1],
+  [-1, 1],
+  [1, -1],
+  [1, 1]
+].flatMap(
+  ([xSign, ySign]) => createCornerViaPositions(
+    xSign,
+    ySign,
+    xSign === -1 || ySign === -1 ? BREADBOARD_CORNER_VIA_X_OUTWARD_SHIFT : 0
+  )
 );
 var BREADBOARD_CLAD_VIA_POSITIONS = [
   ...BREADBOARD_CLAD_VIA_ROW_YS.flatMap(
     (y) => BREADBOARD_COLUMN_XS.map((x) => ({ x, y }))
   ),
-  ...BREADBOARD_OUTER_VIA_ROW_YS.flatMap(
-    (y) => BREADBOARD_COLUMN_XS.map((x) => ({ x, y }))
-  ),
-  ...BREADBOARD_OUTER_VIA_COLUMN_XS.flatMap(
-    (x) => BREADBOARD_OUTER_VERTICAL_VIA_YS.map((y) => ({ x, y }))
-  )
+  ...BREADBOARD_CORNER_VIA_POSITIONS
 ];
 var terminalPinLabels = Object.fromEntries(
   BREADBOARD_TERMINAL_HEADER_POSITIONS.map((position) => [
@@ -15665,16 +15723,9 @@ var terminalPinLabels = Object.fromEntries(
     [position.label]
   ])
 );
-var powerPinLabels = Object.fromEntries(
-  BREADBOARD_COLUMN_XS.map((_, index) => [
-    `pin${index + 1}`,
-    [`COL${index + 1}`]
-  ])
-);
 var terminalPinNames = BREADBOARD_TERMINAL_HEADER_POSITIONS.map(
   (position) => `pin${position.pin}`
 );
-var powerPinNames = BREADBOARD_COLUMN_XS.map((_, index) => `pin${index + 1}`);
 var BreadboardTerminalHeaderFootprint = () => /* @__PURE__ */ (0, import_jsx_runtime4.jsx)("footprint", { insertionDirection: "from_above", children: BREADBOARD_TERMINAL_HEADER_POSITIONS.map((position) => /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(import_react4.Fragment, { children: position.pin === 1 ? /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(
   "platedhole",
   {
@@ -15697,26 +15748,6 @@ var BreadboardTerminalHeaderFootprint = () => /* @__PURE__ */ (0, import_jsx_run
     pcbY: position.y
   }
 ) }, `terminal-${position.label}`)) });
-var BreadboardPowerHeaderFootprint = () => /* @__PURE__ */ (0, import_jsx_runtime4.jsx)("footprint", { insertionDirection: "from_above", children: BREADBOARD_COLUMN_XS.map((x, index) => /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(import_react4.Fragment, { children: index === 0 ? /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(
-  "platedhole",
-  {
-    portHints: [`pin${index + 1}`],
-    shape: "circular_hole_with_rect_pad",
-    holeDiameter: `${BREADBOARD_HEADER_HOLE_DIAMETER}mm`,
-    rectPadWidth: `${BREADBOARD_HEADER_PAD_DIAMETER}mm`,
-    rectPadHeight: `${BREADBOARD_HEADER_PAD_DIAMETER}mm`,
-    pcbX: x
-  }
-) : /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(
-  "platedhole",
-  {
-    portHints: [`pin${index + 1}`],
-    shape: "circle",
-    holeDiameter: `${BREADBOARD_HEADER_HOLE_DIAMETER}mm`,
-    outerDiameter: `${BREADBOARD_HEADER_PAD_DIAMETER}mm`,
-    pcbX: x
-  }
-) }, `power-pin-${index + 1}`)) });
 var BreadboardTerminalHeaders = (props) => /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(
   "connector",
   {
@@ -15727,20 +15758,6 @@ var BreadboardTerminalHeaders = (props) => /* @__PURE__ */ (0, import_jsx_runtim
     ...props
   }
 );
-var BreadboardPowerHeader = ({
-  rail,
-  ...props
-}) => /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(
-  "connector",
-  {
-    pinLabels: powerPinLabels,
-    manufacturerPartNumber: "GENERIC-BREADBOARD-1X21-FEMALE-2.54MM",
-    footprint: /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(BreadboardPowerHeaderFootprint, {}),
-    noSchematicRepresentation: true,
-    pcbY: BREADBOARD_POWER_RAILS.find((candidate) => candidate.id === rail).y,
-    ...props
-  }
-);
 var BreadboardClad = ({
   children,
   autorouter,
@@ -15789,14 +15806,6 @@ var BreadboardClad = ({
           noConnect: headerNoConnects?.terminals ?? (markHeadersNoConnect ? terminalPinNames : void 0)
         }
       ),
-      BREADBOARD_POWER_RAILS.map((rail) => /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(import_react4.Fragment, { children: /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(
-        BreadboardPowerHeader,
-        {
-          rail: rail.id,
-          name: `J_${rail.id.replace(/([A-Z])/g, "_$1").toUpperCase()}`,
-          noConnect: headerNoConnects?.[rail.id] ?? (markHeadersNoConnect ? powerPinNames : void 0)
-        }
-      ) }, rail.id)),
       [1, 5, 10, 15, 20, BREADBOARD_COLUMN_COUNT].map((column) => /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(import_react4.Fragment, { children: /* @__PURE__ */ (0, import_jsx_runtime4.jsx)(
         "silkscreentext",
         {
@@ -16498,15 +16507,18 @@ var XiaoCladWithPerforatedPinHeaders = ({
   BREADBOARD_CLAD_WIDTH,
   BREADBOARD_COLUMN_COUNT,
   BREADBOARD_COLUMN_XS,
+  BREADBOARD_CORNER_VIA_ARM_WIDTH,
+  BREADBOARD_CORNER_VIA_POSITIONS,
+  BREADBOARD_CORNER_VIA_SPACING,
+  BREADBOARD_CORNER_VIA_X_INNER_OFFSET,
+  BREADBOARD_CORNER_VIA_X_OUTER_OFFSET,
+  BREADBOARD_CORNER_VIA_X_OUTWARD_SHIFT,
+  BREADBOARD_CORNER_VIA_Y_INNER_OFFSET,
+  BREADBOARD_CORNER_VIA_Y_OUTER_OFFSET,
   BREADBOARD_HEADER_HOLE_DIAMETER,
   BREADBOARD_HEADER_PAD_DIAMETER,
   BREADBOARD_HEADER_PITCH,
   BREADBOARD_MOUNTING_HOLE_DIAMETER,
-  BREADBOARD_OUTER_VERTICAL_VIA_YS,
-  BREADBOARD_OUTER_VIA_COLUMN_XS,
-  BREADBOARD_OUTER_VIA_ROW_YS,
-  BREADBOARD_POWER_HEADER_POSITIONS,
-  BREADBOARD_POWER_RAILS,
   BREADBOARD_TERMINAL_HEADER_POSITIONS,
   BREADBOARD_TERMINAL_ROW_LABELS,
   BREADBOARD_TERMINAL_ROW_YS,
@@ -16516,7 +16528,6 @@ var XiaoCladWithPerforatedPinHeaders = ({
   BoosterPackLeftHeader,
   BoosterPackRightHeader,
   BreadboardClad,
-  BreadboardPowerHeader,
   BreadboardTerminalHeaders,
   CLAD_40X40_EDGE_MOUNTING_HOLE_INSET,
   CLAD_40X40_HEIGHT,