bambu-printer-mcp 1.1.87 → 1.1.89

This diff represents the content of publicly available package versions that have been released to one of the supported registries. The information contained in this diff is provided for informational purposes only and reflects changes between package versions as they appear in their respective public registries.
@@ -25,15 +25,17 @@ Find out before you design, and before you ask. Research whenever the request na
25
25
  6. For what is still unknown after about two rounds per fact, shape the design so that fact does not decide whether it works (an adjustable or sprung interface, a foot that suits more than one surface), or state a bounded assumption as an assumption. Ask the person only as the last resort, one short question, and only for what exists nowhere but with them. Never ask for something a search answers: a photo of their car's dashboard, the size of a named product, what a named surface is made of.
26
26
  Without web tools, say so in the result, use what you recall labelled as recalled rather than published, and lean harder on step 6.
27
27
 
28
+ Before choosing a mechanism, establish what every working bought or published version of the thing has, and keep all of it. For example, a car phone holder turns and tilts to face the driver; a mount's base is sized by the moment of what it holds, not just its weight; an adhesive mount uses a full pad of the tape's grade, not a strip, on a surface the tape suits. Start from the complete product a capable designer would describe at once, then make it printable. A design that leaves out a feature they all have says what it lost and why that is acceptable for this person.
29
+
28
30
  Choose each fit by what that interface has to do: drop in and lift out, slide, locate without rattle, grip so it does not slip or turn, snap over, or press in to stay. There is no single fit number. Keep three things apart for each interface: the object's size and how sure it is, the correction this printer and orientation need (its own observed corrections first, when the context supplies them), and the fit the function calls for. When the size's uncertainty is wider than the function tolerates, do not answer with a better number: choose a mechanism that absorbs the difference (crush ribs, a split closed by a screw, a flexure, a snap), or ask for the one measurement that settles it. The same object changes with time and use: full and nearly empty, new and worn, soft and stiff. A fit that relies on the object giving way must still work in its stiffest, largest state, and a pocket is sized to the widest section the object passes through on the way in, with support where the object actually bears, not to its bounding box.
29
31
 
30
32
  Evaluate printability locally. Distinguish a progressively supported overhang, a bridge anchored at both ends, and a disconnected island. State overhang angles from vertical: 0 degrees is a vertical wall; 90 degrees is a horizontal underside. Convert conventions before setting slicer angles. Use relevant measured capability ahead of generic rules. A 45-degree threshold is not a universal support requirement, and a steep surface is not automatically unprintable. Judge bridge length along the actual unsupported extrusion path, with its anchors, cooling, material, and required underside quality. A feature that survives printing may still miss a cosmetic or dimensional requirement.
31
33
 
32
34
  Resolve a difficult region with the least disruptive effective change: a better orientation, local geometry, suitable process settings, accessible support, a deliberate breakaway feature, or a split. Supports are an ordinary manufacturing option. Preserve attractive curves and useful complexity when modest support or cleanup achieves them. Check support removal and tool access, especially inside cavities. Avoid changing the whole object to solve a local problem.
33
35
 
34
- Choose layer orientation, material, walls, and joints for the actual loads and environment. Check the load path, flexing features, fastener access, and installation sequence. A reduction in supports or color changes must not silently weaken the part or defeat its fit.
36
+ Choose layer orientation, material, walls, and joints for the actual loads and environment. Check the load path, flexing features, fastener access, and installation sequence. Judge a connection (tape, screws, a snap) against products that demonstrably work. If a check says a bought product that holds for years would fail, the check is wrong: correct it, then apply it to your design. A reduction in supports or color changes must not silently weaken the part or defeat its fit.
35
37
 
36
- When a part must flex, grip, snap, clip, spring, or hold something, consider a compliant mechanism first: one piece that bends on purpose often beats rigid jaws plus a clamp bolt, with fewer parts, no fastener to buy or lose, and a hold that follows the object. Spread the bending over a long band, leaf, or arch rather than a short stub; keep the rest of the body stiff so the stroke goes where you intend; give a hand enough leverage; design the preload in; use an over-centre or cam where a hold must lock; and give every flexing direction a hard stop so a hard pull meets solid material. Keep the bending in the layer plane, where the filament runs along the strain; bending that pulls layers apart is far weaker and fails with little warning. Choose the strain by duty (bent once to assemble, bent every day, and held bent for months are different designs) and by material and direction, using the printer's own observed values when the context supplies them. Modern PLA and PETG grades are not brittle in this role: proven printed springs work daily at strains that older moulded-plastic tables would forbid. What usually ends a flexure is not a clean snap at a magic percentage but whitening and set at a sharp root, layers parting where the bend crosses them, or a held bend creeping loose, faster when warm. In sustained heat such as a parked car, a part held bent relaxes and a sun-heated dashboard can exceed what PLA or PETG carry under load: prefer a rest state that sits unstrained, and say so when the material cannot honestly do the job. A part a hand works has to be easy to work, and that is checked like its hold: say where the fingers go, how hard they push to open it, how far it opens, and how the object goes in and comes out with one hand. A grip that meets its force and is a fight to use has failed the brief.
38
+ When a part must flex, grip, snap, clip, spring, or hold something, consider a compliant mechanism first: one piece that bends on purpose often beats rigid jaws plus a clamp bolt, with fewer parts, no fastener to buy or lose, and a hold that follows the object. That choice is for the element that grips, clips or springs, not for the product: it is never a reason to make the whole thing one piece or to drop a joint, adjustment or base the bought versions have. Spread the bending over a long band, leaf, or arch rather than a short stub; keep the rest of the body stiff so the stroke goes where you intend; give a hand enough leverage; design the preload in; use an over-centre or cam where a hold must lock; and give every flexing direction a hard stop so a hard pull meets solid material. Keep the bending in the layer plane, where the filament runs along the strain; bending that pulls layers apart is far weaker and fails with little warning. Choose the strain by duty (bent once to assemble, bent every day, and held bent for months are different designs) and by material and direction, using the printer's own observed values when the context supplies them. Modern PLA and PETG grades are not brittle in this role: proven printed springs work daily at strains that older moulded-plastic tables would forbid. What usually ends a flexure is not a clean snap at a magic percentage but whitening and set at a sharp root, layers parting where the bend crosses them, or a held bend creeping loose, faster when warm. In sustained heat such as a parked car, a part held bent relaxes and a sun-heated dashboard can exceed what PLA or PETG carry under load: prefer a rest state that sits unstrained, and say so when the material cannot honestly do the job. A part a hand works has to be easy to work, and that is checked like its hold: say where the fingers go, how hard they push to open it, how far it opens, and how the object goes in and comes out with one hand. A grip that meets its force and is a fight to use has failed the brief.
37
39
 
38
40
  On a shared-nozzle multicolor setup, reason about filament transitions across layers, including support-interface material. Total color count alone is a poor cost estimate. Consider color placement, shallow inlays, separately printed accents, and part orientation while preserving the requested appearance. Separate bodies on one layer-printed plate can still cause repeated swaps. Use the slicer's actual schedule and estimates when available; do not invent a fixed cost per color change.
39
41
 
@@ -77,7 +79,7 @@ Return a concise decision: keep, revise, or validate one specific uncertainty. I
77
79
 
78
80
  export const FDM_FLEXURES = `Apply this guidance when a part must flex, grip, snap, clip, spring, or hold something by bending. The strain bands below are planning bands drawn from manufacturer printed-specimen cards, measurements of published mechanisms that survive daily use, and single-printer coupon readings. They are not guarantees and not rejection thresholds. When the context supplies this printer's own observed values for the same filament, profile and duty, design to those and keep the generic band as the starting point for everything else.
79
81
 
80
- A compliant design earns its place when one bending piece replaces rigid jaws, a hinge and a clamp bolt: fewer parts, nothing to buy or lose, one print, and a hold that follows the object as it varies. Prefer it for holders, clips, snaps, lids and latches a hand operates. Do not force it where the job is precise location under a heavy sustained load, a preload that must not relax for months in heat, or travel and force together beyond what a spring can give. There, let solid geometry carry the load (a pin, saddle, rail, shoulder or latch) and let a spring only preload, return, or take up slack.
82
+ A compliant design earns its place when one bending piece replaces rigid jaws, a hinge and a clamp bolt: fewer parts, nothing to buy or lose, one print, and a hold that follows the object as it varies. Prefer it for holders, clips, snaps, lids and latches a hand operates, as the element that grips or latches, never in place of a joint, adjustment or base the bought versions have. Do not force it where the job is precise location under a heavy sustained load, a preload that must not relax for months in heat, or travel and force together beyond what a spring can give. There, let solid geometry carry the load (a pin, saddle, rail, shoulder or latch) and let a spring only preload, return, or take up slack.
81
83
 
82
84
  Choose the architecture before the dimensions. A long leaf, band or arch spreads strain over its length; a short stub concentrates it at the root and either cracks or barely moves. A pair of leaves guided at both ends moves its jaw straight, without tilting. Folding the spring back on itself (a serpentine or S) buys travel in a small space at the same strain. A thick curved arch gives a strong bite over a short opening. An over-centre toggle or cam locks past its peak so the locked strain is lower than the click that got there, and both rest states can sit nearly unstrained. A shallow pre-curved beam latched flat seals along its length while held at a fraction of a percent. A cam lever earns a hard bite by putting its small lift into a short, stiff spring, not by bending long jaws. In every case keep the surrounding body much stiffer than the spring, size the leverage to the hand that works it, design the preload in rather than hoping assembly provides it, and put a solid hard stop just past the working stroke so an oversize object or a hard yank meets compression instead of ever-rising strain.
83
85