@willieee802/zigbee-herdsman-converters 19.44.3 → 19.45.0

package/dist/devices/efekta.js

@@ -1536,6 +1536,15 @@ exports.definitions = [
                 description: "Setting the sensor reading interval in seconds, by default 40 seconds",
                 access: "STATE_SET",
             }),
+            m.binary({
+                name: "heater",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msTemperatureMeasurement",
+                attribute: { ID: 0x0525, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Activation of the sensor heating service mode, 15 minutes",
+                access: "STATE_SET",
+            }),
             m.enumLookup({
                 name: "tx_radio_power",
                 lookup: { "4dbm": 4, "19dbm": 19 },
@@ -1725,6 +1734,14 @@ exports.definitions = [
                 description: "Set TX Radio Power, dbm",
                 access: "STATE_SET",
             }),
+            m.enumLookup({
+                name: "resolution",
+                lookup: { "9 bit": 9, "10 bit": 10, "11 bit": 11, "12 bit": 12 },
+                cluster: "msTemperatureMeasurement",
+                attribute: { ID: 0x0520, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Set Bit resolution DS18B20",
+                access: "STATE_SET",
+            }),
             m.binary({
                 name: "smart_sleep",
                 valueOn: ["ON", 1],
@@ -2985,7 +3002,7 @@ exports.definitions = [
             }),
             m.numeric({
                 name: "pressure_offset",
-                unit: "kPa",
+                unit: "hPa",
                 valueMin: -100.0,
                 valueMax: 100.0,
                 cluster: "msPressureMeasurement",
@@ -3019,6 +3036,13 @@ exports.definitions = [
                 description: "Recalibrated sensor raw temperature",
                 access: "STATE",
             }),
+            m.enumLookup({
+                name: "range",
+                lookup: { "0-10 Bar": 10, "0-16 Bar": 16 },
+                cluster: "msPressureMeasurement",
+                attribute: { ID: 0x0280, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Measuring range of the sensor",
+            }),
             m.battery({
                 percentage: true,
                 lowStatus: true,
@@ -3121,7 +3145,7 @@ exports.definitions = [
             }),
             m.numeric({
                 name: "pressure_offset",
-                unit: "kPa",
+                unit: "hPa",
                 valueMin: -100.0,
                 valueMax: 100.0,
                 cluster: "msPressureMeasurement",
@@ -3139,6 +3163,13 @@ exports.definitions = [
                 description: "Adjust first temperature sensor",
                 access: "STATE_SET",
             }),
+            m.enumLookup({
+                name: "range",
+                lookup: { "0-10 Bar": 10, "0-16 Bar": 16 },
+                cluster: "msPressureMeasurement",
+                attribute: { ID: 0x0280, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Measuring range of the sensor",
+            }),
             m.numeric({
                 name: "mains_voltage",
                 unit: "V",
@@ -3307,7 +3338,7 @@ exports.definitions = [
             }),
             m.enumLookup({
                 name: "sensor_type",
-                lookup: { "0-1bar": 1, "0-5bar": 5, "0-10bar": 10 },
+                lookup: { "0-1bar": 1, "0-5bar": 5, "0-6bar": 6, "0-10bar": 10, "0-12bar": 12, "0-40bar": 40 },
                 cluster: "msPressureMeasurement",
                 attribute: { ID: 0x0280, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
                 description: "Set sensor type",
@@ -3389,7 +3420,7 @@ exports.definitions = [
             }),
             m.numeric({
                 name: "pressure_offset",
-                unit: "kPa",
+                unit: "hPa",
                 valueMin: -100.0,
                 valueMax: 100.0,
                 cluster: "msPressureMeasurement",
@@ -3423,6 +3454,13 @@ exports.definitions = [
                 description: "Recalibrated sensor raw temperature",
                 access: "STATE",
             }),
+            m.enumLookup({
+                name: "range",
+                lookup: { "0-10 Bar": 10, "0-16 Bar": 16 },
+                cluster: "msPressureMeasurement",
+                attribute: { ID: 0x0280, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Measuring range of the sensor",
+            }),
             m.battery({
                 percentage: true,
                 lowStatus: true,
@@ -3543,6 +3581,14 @@ exports.definitions = [
                 description: "Adjust first temperature sensor",
                 access: "STATE_SET",
             }),
+            m.enumLookup({
+                endpointName: "1",
+                name: "range",
+                lookup: { "0-10 Bar": 10, "0-16 Bar": 16 },
+                cluster: "msPressureMeasurement",
+                attribute: { ID: 0x0280, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Measuring range of the first sensor",
+            }),
             m.pressure({
                 endpointNames: ["2"],
                 unit: "kPa",
@@ -3601,6 +3647,14 @@ exports.definitions = [
                 description: "Adjust second temperature sensor",
                 access: "STATE_SET",
             }),
+            m.enumLookup({
+                endpointName: "2",
+                name: "range",
+                lookup: { "0-10 Bar": 10, "0-16 Bar": 16 },
+                cluster: "msPressureMeasurement",
+                attribute: { ID: 0x0280, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Measuring range of the first sensor",
+            }),
             m.battery({
                 percentage: true,
                 lowStatus: true,
@@ -3721,6 +3775,14 @@ exports.definitions = [
                 description: "Adjust first temperature sensor",
                 access: "STATE_SET",
             }),
+            m.enumLookup({
+                endpointName: "1",
+                name: "range",
+                lookup: { "0-10 Bar": 10, "0-16 Bar": 16 },
+                cluster: "msPressureMeasurement",
+                attribute: { ID: 0x0280, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Measuring range of the first sensor",
+            }),
             m.pressure({
                 endpointNames: ["2"],
                 unit: "kPa",
@@ -3779,6 +3841,14 @@ exports.definitions = [
                 description: "Adjust second temperature sensor",
                 access: "STATE_SET",
             }),
+            m.enumLookup({
+                endpointName: "2",
+                name: "range",
+                lookup: { "0-10 Bar": 10, "0-16 Bar": 16 },
+                cluster: "msPressureMeasurement",
+                attribute: { ID: 0x0280, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Measuring range of the first sensor",
+            }),
             m.battery({
                 percentage: true,
                 lowStatus: true,
@@ -3907,6 +3977,14 @@ exports.definitions = [
                 description: "Adjust first temperature sensor",
                 access: "STATE_SET",
             }),
+            m.enumLookup({
+                endpointName: "1",
+                name: "range",
+                lookup: { "0-10 Bar": 10, "0-16 Bar": 16 },
+                cluster: "msPressureMeasurement",
+                attribute: { ID: 0x0280, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Measuring range of the first sensor",
+            }),
             m.pressure({
                 endpointNames: ["2"],
                 unit: "kPa",
@@ -3965,6 +4043,14 @@ exports.definitions = [
                 description: "Adjust second temperature sensor",
                 access: "STATE_SET",
             }),
+            m.enumLookup({
+                endpointName: "2",
+                name: "range",
+                lookup: { "0-10 Bar": 10, "0-16 Bar": 16 },
+                cluster: "msPressureMeasurement",
+                attribute: { ID: 0x0280, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Measuring range of the first sensor",
+            }),
             m.numeric({
                 name: "mains_voltage",
                 unit: "V",
@@ -4199,6 +4285,14 @@ exports.definitions = [
                 description: "Setting the sensor reading interval in seconds, by default 10 seconds",
                 access: "STATE_SET",
             }),
+            m.enumLookup({
+                name: "sensor_type",
+                lookup: { "0-1bar": 1, "0-5bar": 5, "0-6bar": 6, "0-10bar": 10, "0-12bar": 12, "0-40bar": 40 },
+                cluster: "genPowerCfg",
+                attribute: { ID: 0x0280, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Set sensor type",
+                access: "STATE_SET",
+            }),
             m.enumLookup({
                 name: "tx_radio_power",
                 lookup: { "4dbm": 4, "19dbm": 19 },
@@ -5043,18 +5137,6 @@ exports.definitions = [
                 description: "Upper level of soil moisture 100% is:",
                 access: "STATE_SET",
             }),
-            m.numeric({
-                name: "temperature_offset",
-                unit: "°C",
-                valueMin: -50,
-                valueMax: 50,
-                valueStep: 0.1,
-                scale: 10,
-                cluster: "msTemperatureMeasurement",
-                attribute: { ID: 0x0410, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
-                description: "Adjust temperature",
-                access: "STATE_SET",
-            }),
             m.binary({
                 name: "temperature_compensation",
                 valueOn: ["ON", 1],
@@ -5165,18 +5247,6 @@ exports.definitions = [
                 description: "Upper level of soil moisture 100% is:",
                 access: "STATE_SET",
             }),
-            m.numeric({
-                name: "temperature_offset",
-                unit: "°C",
-                valueMin: -50,
-                valueMax: 50,
-                valueStep: 0.1,
-                scale: 10,
-                cluster: "msTemperatureMeasurement",
-                attribute: { ID: 0x0410, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
-                description: "Adjust temperature",
-                access: "STATE_SET",
-            }),
             m.binary({
                 name: "temperature_compensation",
                 valueOn: ["ON", 1],
@@ -5287,18 +5357,6 @@ exports.definitions = [
                 description: "Upper level of soil moisture 100% is:",
                 access: "STATE_SET",
             }),
-            m.numeric({
-                name: "temperature_offset",
-                unit: "°C",
-                valueMin: -50,
-                valueMax: 50,
-                valueStep: 0.1,
-                scale: 10,
-                cluster: "msTemperatureMeasurement",
-                attribute: { ID: 0x0410, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
-                description: "Adjust temperature",
-                access: "STATE_SET",
-            }),
             m.binary({
                 name: "temperature_compensation",
                 valueOn: ["ON", 1],
@@ -5409,18 +5467,6 @@ exports.definitions = [
                 description: "Upper level of soil moisture 100% is:",
                 access: "STATE_SET",
             }),
-            m.numeric({
-                name: "temperature_offset",
-                unit: "°C",
-                valueMin: -50,
-                valueMax: 50,
-                valueStep: 0.1,
-                scale: 10,
-                cluster: "msTemperatureMeasurement",
-                attribute: { ID: 0x0410, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
-                description: "Adjust temperature",
-                access: "STATE_SET",
-            }),
             m.binary({
                 name: "temperature_compensation",
                 valueOn: ["ON", 1],
@@ -6030,6 +6076,14 @@ exports.definitions = [
                 description: "Setting the sensor report delay. Setting the time in seconds (20-1800), by default 60 seconds",
                 access: "STATE_SET",
             }),
+            m.enumLookup({
+                name: "power_mode",
+                lookup: { Fast: 1, Medium: 5, Slow: 10 },
+                cluster: "genPowerCfg",
+                attribute: { ID: 0x0201, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Set power mode",
+                access: "STATE_SET",
+            }),
             m.binary({
                 name: "forced_recalibration",
                 valueOn: ["ON", 1],
@@ -6511,6 +6565,50 @@ exports.definitions = [
                 access: "STATE",
                 reporting: pmReporting,
             }),
+            m.numeric({
+                name: "tvoc",
+                unit: "ppb",
+                cluster: "genAnalogInput",
+                attribute: "presentValue",
+                description: "TVOC",
+                access: "STATE",
+                reporting: defaultReporting,
+            }),
+            m.numeric({
+                name: "eco2",
+                unit: "ppm",
+                cluster: "genAnalogInput",
+                attribute: { ID: 0x0175, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "eCO2",
+                access: "STATE",
+                reporting: defaultReporting,
+            }),
+            m.numeric({
+                name: "aqi",
+                unit: "index",
+                cluster: "genAnalogInput",
+                attribute: { ID: 0x0185, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "aqi",
+                access: "STATE",
+                reporting: defaultReporting,
+            }),
+            m.numeric({
+                name: "indicator_corection",
+                valueMin: -15,
+                valueMax: 15,
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0333, type: zigbee_herdsman_1.Zcl.DataType.INT8 },
+                description: "Indicator corection",
+                access: "STATE_SET",
+            }),
+            m.enumLookup({
+                name: "invert_color",
+                lookup: { WB: 0, BW: 1 },
+                cluster: "pm25Measurement",
+                attribute: { ID: 0xf004, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Set color mode",
+                access: "STATE_SET",
+            }),
         ],
     },
     {
@@ -6995,6 +7093,15 @@ exports.definitions = [
                 description: "Setting the sensor reading interval in seconds, by default 5 seconds",
                 access: "STATE_SET",
             }),
+            m.binary({
+                name: "heater",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msTemperatureMeasurement",
+                attribute: { ID: 0x0525, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Activation of the sensor heating service mode, 15 minutes",
+                access: "STATE_SET",
+            }),
             m.enumLookup({
                 name: "tx_radio_power",
                 lookup: { "4dbm": 4, "19dbm": 19 },
@@ -7673,7 +7780,7 @@ exports.definitions = [
     {
         zigbeeModel: ["Netuya_CO2_Smart_Box", "Netuya_CO2_Smart_Box_PA"],
         model: "Netuya_CO2_Smart_Box",
-        vendor: "Efektalab",
+        vendor: "EFEKTA",
         description: "CO2 Smart Monitor, rgb indicator, alarm, can control the relay",
         ota: true,
         extend: [
@@ -7735,7 +7842,7 @@ exports.definitions = [
                 access: "STATE_SET",
             }),
             m.numeric({
-                name: "alarm volume",
+                name: "alarm_volume",
                 valueMin: 0,
                 valueMax: 10,
                 cluster: "msCO2",
@@ -7744,7 +7851,7 @@ exports.definitions = [
                 access: "STATE_SET",
             }),
             m.numeric({
-                name: "alarm level",
+                name: "alarm_level",
                 unit: "ppm",
                 valueMin: 400,
                 valueMax: 5000,
@@ -7754,7 +7861,7 @@ exports.definitions = [
                 access: "STATE_SET",
             }),
             m.binary({
-                name: "calibration mode",
+                name: "calibration_mode",
                 valueOn: ["Auto", 1],
                 valueOff: ["Manual", 0],
                 cluster: "msCO2",
@@ -7924,6 +8031,14 @@ exports.definitions = [
                 description: "Set TX Radio Power, dbm",
                 access: "STATE_SET",
             }),
+            m.enumLookup({
+                name: "sensor_type",
+                lookup: { "0-1bar": 1, "0-5bar": 5, "0-6bar": 6, "0-10bar": 10, "0-12bar": 12, "0-40bar": 40 },
+                cluster: "msPressureMeasurement",
+                attribute: { ID: 0x0280, type: 0x20 },
+                description: "Set sensor type",
+                access: "STATE_SET",
+            }),
             m.binary({
                 name: "comparison_previous_data",
                 valueOn: ["ON", 1],
@@ -8172,11 +8287,11 @@ exports.definitions = [
                 access: "STATE",
             }),
             m.enumLookup({
-                name: "оperating_mode",
-                lookup: { Normal: 0, "Energy-saving": 1 },
+                name: "power_mode",
+                lookup: { Fast: 1, Medium: 5, Slow: 10 },
                 cluster: "genPowerCfg",
-                attribute: { ID: 0xf005, type: 0x20 },
-                description: "Set data output on the display",
+                attribute: { ID: 0x0201, type: 0x21 },
+                description: "Set power mode",
                 access: "STATE_SET",
             }),
             m.enumLookup({
@@ -8226,5 +8341,1445 @@ exports.definitions = [
             }),
         ],
     },
+    {
+        zigbeeModel: ["EFEKTA_TDS_Monitor"],
+        model: "EFEKTA_TDS_Monitor",
+        vendor: "EFEKTA",
+        description: "TDS Monitor with DS18B20 temperature sensor",
+        extend: [
+            m.temperature({
+                reporting: fourReporting,
+                access: "STATE",
+            }),
+            m.numeric({
+                name: "tds",
+                unit: "ppm",
+                cluster: "genBasic",
+                attribute: { ID: 0x0555, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured TDS value",
+                access: "STATE",
+                reporting: pmReporting,
+                precision: 1,
+            }),
+            m.enumLookup({
+                name: "tds_coefficient",
+                lookup: { "500": 500, "550": 550, "640": 640, "700": 700, "1000": 1000 },
+                cluster: "genBasic",
+                attribute: { ID: 0x0557, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "TDS coefficient",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "reading_interval",
+                unit: "Seconds",
+                valueMin: 10,
+                valueMax: 360,
+                cluster: "genBasic",
+                attribute: { ID: 0x0201, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Setting the sensor reading interval in seconds, by default 30 seconds",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "tds_offset",
+                unit: "ppm",
+                valueMin: -100.0,
+                valueMax: 100.0,
+                valueStep: 0.1,
+                cluster: "genBasic",
+                attribute: { ID: 0x0556, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Adjust TDS",
+                access: "STATE_SET",
+            }),
+            m.enumLookup({
+                name: "tx_radio_power",
+                lookup: { "4dbm": 4, "19dbm": 19 },
+                cluster: "genBasic",
+                attribute: { ID: 0x0236, type: zigbee_herdsman_1.Zcl.DataType.INT8 },
+                description: "Set TX Radio Power, dbm",
+                access: "STATE_SET",
+            }),
+        ],
+    },
+    {
+        zigbeeModel: ["DIYRuZ_AirSense_Reloaded"],
+        model: "DIYRuZ_AirSense_Reloaded",
+        vendor: "EFEKTA",
+        description: "Air quality sensor (CO2, formaldehyde, temperature, humidity, pressure)",
+        extend: [
+            m.identify(),
+            m.co2({
+                reporting: { min: 20, max: 600, change: 0.000001 },
+                access: "STATE_GET",
+            }),
+            m.numeric({
+                name: "formaldehyde_concentration",
+                unit: "ppm",
+                cluster: "msFormaldehyde",
+                attribute: "measuredValue",
+                description: "Formaldehyde (CH2O) concentration",
+                access: "STATE_GET",
+                reporting: { min: 20, max: 600, change: 0.001 },
+            }),
+            m.temperature({
+                reporting: { min: 20, max: 1200, change: 15 },
+                access: "STATE_GET",
+            }),
+            m.pressure({
+                reporting: { min: 60, max: 1800, change: 1 },
+                access: "STATE_GET",
+            }),
+            m.humidity({
+                reporting: { min: 20, max: 1200, change: 15 },
+                access: "STATE_GET",
+            }),
+            m.binary({
+                name: "co2_accurate_measurement",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0xf111, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Enable/disable accurate CO2 measurement mode",
+                access: "ALL",
+            }),
+            m.binary({
+                name: "co2_automatic_calibration",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0202, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Enable/disable automatic calibration of CO2 sensor",
+                access: "ALL",
+            }),
+            m.binary({
+                name: "led_indication",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0203, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Enable/disable LED indication",
+                access: "ALL",
+            }),
+            m.numeric({
+                name: "co2_moderate_threshold",
+                unit: "ppm",
+                valueMin: 0,
+                valueMax: 5000,
+                valueStep: 1,
+                cluster: "msCO2",
+                attribute: { ID: 0x0204, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Threshold for moderate CO2 level",
+                access: "ALL",
+            }),
+            m.numeric({
+                name: "co2_hazardous_threshold",
+                unit: "ppm",
+                valueMin: 0,
+                valueMax: 5000,
+                valueStep: 1,
+                cluster: "msCO2",
+                attribute: { ID: 0x0205, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Threshold for hazardous CO2 level",
+                access: "ALL",
+            }),
+            m.numeric({
+                name: "formaldehyde_moderate_threshold",
+                unit: "ppb",
+                valueMin: 0,
+                valueMax: 5000,
+                valueStep: 1,
+                cluster: "msFormaldehyde",
+                attribute: { ID: 0x0204, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Threshold for moderate formaldehyde (CH2O) level",
+                access: "ALL",
+            }),
+            m.numeric({
+                name: "formaldehyde_hazardous_threshold",
+                unit: "ppb",
+                valueMin: 0,
+                valueMax: 5000,
+                valueStep: 1,
+                cluster: "msFormaldehyde",
+                attribute: { ID: 0x0205, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Threshold for hazardous formaldehyde (CH2O) level",
+                access: "ALL",
+            }),
+            m.numeric({
+                name: "temperature_offset",
+                unit: "°C",
+                valueMin: -20,
+                valueMax: 20,
+                valueStep: 0.1,
+                scale: 10,
+                cluster: "msTemperatureMeasurement",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Temperature calibration offset",
+                access: "ALL",
+            }),
+            m.numeric({
+                name: "humidity_offset",
+                unit: "%",
+                valueMin: -50,
+                valueMax: 50,
+                valueStep: 1,
+                cluster: "msRelativeHumidity",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Humidity calibration offset",
+                access: "ALL",
+            }),
+            m.numeric({
+                name: "pressure_offset",
+                unit: "hPa",
+                valueMin: -1000,
+                valueMax: 1000,
+                valueStep: 1,
+                cluster: "msPressureMeasurement",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Pressure calibration offset",
+                access: "ALL",
+            }),
+            m.numeric({
+                name: "formaldehyde_offset",
+                unit: "adc",
+                valueMin: -100,
+                valueMax: 100,
+                valueStep: 1,
+                cluster: "msFormaldehyde",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT8 },
+                description: "Formaldehyde ADC range calibration offset",
+                access: "STATE_SET",
+            }),
+        ],
+    },
+    {
+        zigbeeModel: ["EFEKTA_Air_Quality_Station_2"],
+        model: "EFEKTA_Air_Quality_Station_2",
+        vendor: "EFEKTA",
+        description: "EFEKTA Air Quality Station2, PM0.5, PM1.0, PM2.5, PM4.0, PM10, PM Size, CO2, VOC Index, NOx Index, Temperature, Humidity, TFT display 3.2 inches.",
+        extend: [
+            m.co2({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.numeric({
+                name: "pm1",
+                unit: "µg/m³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0601, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM1.0 (particulate matter) concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.pm25({
+                reporting: false,
+                access: "STATE",
+                description: "Measured PM2.5 (particulate matter) concentration",
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm4",
+                unit: "µg/m³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0605, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM4.0 (particulate matter) concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm10",
+                unit: "µg/m³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0602, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM10.0 (particulate matter) concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_size",
+                unit: "µm",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0603, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Typical Particle Size",
+                access: "STATE",
+                reporting: false,
+                precision: 2,
+            }),
+            m.numeric({
+                name: "pm_n05",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0640, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM0.5 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n1",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0641, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM1.0 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n25",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0642, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM2.5 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n4",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0643, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM4.0 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n10",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0644, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM10.0 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "voc_index",
+                unit: "VOC Index points",
+                cluster: "genAnalogInput",
+                attribute: "presentValue",
+                description: "VOC index",
+                access: "STATE",
+                reporting: false,
+            }),
+            m.numeric({
+                name: "nox_index",
+                unit: "NOx Index points",
+                cluster: "genAnalogInput",
+                attribute: { ID: 0x0155, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "NOx index",
+                access: "STATE",
+                reporting: false,
+            }),
+            m.temperature({
+                description: "Measured value of the built-in temperature sensor",
+                reporting: false,
+                access: "STATE",
+            }),
+            m.humidity({
+                description: "Measured value of the built-in humidity sensor",
+                reporting: false,
+                access: "STATE",
+            }),
+            m.illuminance({
+                access: "STATE",
+                reporting: false,
+            }),
+            m.numeric({
+                name: "report_delay",
+                unit: "sec",
+                valueMin: 6,
+                valueMax: 600,
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0201, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Setting the sensor report delay. Setting the time in seconds (6-600), by default 15 seconds",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "auto_brightness",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0203, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Enable or Disable Auto Brightness of the Display",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "night_onoff_backlight",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0401, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Complete shutdown of the backlight at night mode",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "night_on_backlight",
+                unit: "Hr",
+                valueMin: 0,
+                valueMax: 23,
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0405, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Night mode activation time",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "night_off_backlight",
+                unit: "Hr",
+                valueMin: 0,
+                valueMax: 23,
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0406, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Night mode deactivation time",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "temperature_offset",
+                unit: "°C",
+                valueMin: -50,
+                valueMax: 50,
+                valueStep: 0.1,
+                scale: 10,
+                cluster: "msTemperatureMeasurement",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Adjust temperature",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "humidity_offset",
+                unit: "%",
+                valueMin: -50,
+                valueMax: 50,
+                valueStep: 1,
+                cluster: "msRelativeHumidity",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Adjust humidity",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "auto_clean_interval",
+                unit: "day",
+                valueMin: 0,
+                valueMax: 10,
+                valueStep: 1,
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0330, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Auto clean interval PM2.5 sensor",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "manual_clean",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0331, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Manual clean PM2.5 sensor",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "set_altitude",
+                unit: "meters",
+                valueMin: 0,
+                valueMax: 3000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0205, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Setting the altitude above sea level (for high accuracy of the CO2 sensor)",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "forced_recalibration",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0202, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Start FRC (Perform Forced Recalibration of the CO2 Sensor)",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "manual_forced_recalibration",
+                unit: "ppm",
+                valueMin: 0,
+                valueMax: 5000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0207, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Start Manual FRC (Perform Forced Recalibration of the CO2 Sensor)",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "automatic_self_calibration",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0402, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Automatic self calibration",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "factory_reset_co2",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0206, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Factory Reset CO2 sensor",
+                access: "STATE_SET",
+            }),
+        ],
+    },
+    {
+        zigbeeModel: ["EFEKTA_Air_Quality_Station_2c"],
+        model: "EFEKTA_Air_Quality_Station_2c",
+        vendor: "EFEKTA",
+        description: "EFEKTA Air Quality Station, PM0.5, PM1.0, PM2.5, PM4.0, PM10, PM Size, CO2, VOC Index, CH2O, Temperature, Humidity, TFT display 3.2 inches.",
+        extend: [
+            m.co2({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.numeric({
+                name: "pm1",
+                unit: "µg/m³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0601, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM1.0 (particulate matter) concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.pm25({
+                reporting: false,
+                access: "STATE",
+                description: "Measured PM2.5 (particulate matter) concentration",
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm4",
+                unit: "µg/m³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0605, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM4.0 (particulate matter) concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm10",
+                unit: "µg/m³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0602, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM10.0 (particulate matter) concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_size",
+                unit: "µm",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0603, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Typical Particle Size",
+                access: "STATE",
+                reporting: false,
+                precision: 2,
+            }),
+            m.numeric({
+                name: "pm_n05",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0640, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM0.5 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n1",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0641, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM1.0 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n25",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0642, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM2.5 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n4",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0643, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM4.0 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n10",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0644, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM10.0 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "voc_index",
+                unit: "VOC Index points",
+                cluster: "genAnalogInput",
+                attribute: "presentValue",
+                description: "VOC index",
+                access: "STATE",
+                reporting: false,
+            }),
+            m.numeric({
+                name: "nox_index",
+                unit: "NOx Index points",
+                cluster: "genAnalogInput",
+                attribute: { ID: 0x0155, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "NOx index",
+                access: "STATE",
+                reporting: false,
+            }),
+            m.numeric({
+                name: "formaldehyde",
+                unit: "ppb",
+                cluster: "msFormaldehyde",
+                attribute: "measuredValue",
+                description: "Formaldehyde concentration",
+                access: "STATE",
+                reporting: false,
+            }),
+            m.temperature({
+                description: "Measured value of the built-in temperature sensor",
+                reporting: false,
+                access: "STATE",
+            }),
+            m.humidity({
+                description: "Measured value of the built-in humidity sensor",
+                reporting: false,
+                access: "STATE",
+            }),
+            m.illuminance({
+                access: "STATE",
+                reporting: false,
+            }),
+            m.numeric({
+                name: "report_delay",
+                unit: "sec",
+                valueMin: 6,
+                valueMax: 600,
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0201, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Setting the sensor report delay. Setting the time in seconds (6-600), by default 15 seconds",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "auto_brightness",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0203, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Enable or Disable Auto Brightness of the Display",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "night_onoff_backlight",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0401, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Complete shutdown of the backlight at night mode",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "night_on_backlight",
+                unit: "Hr",
+                valueMin: 0,
+                valueMax: 23,
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0405, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Night mode activation time",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "night_off_backlight",
+                unit: "Hr",
+                valueMin: 0,
+                valueMax: 23,
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0406, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Night mode deactivation time",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "temperature_offset",
+                unit: "°C",
+                valueMin: -50,
+                valueMax: 50,
+                valueStep: 0.1,
+                scale: 10,
+                cluster: "msTemperatureMeasurement",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Adjust temperature",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "humidity_offset",
+                unit: "%",
+                valueMin: -50,
+                valueMax: 50,
+                valueStep: 1,
+                cluster: "msRelativeHumidity",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Adjust humidity",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "formaldehyde_offset",
+                unit: "adc",
+                valueMin: -100,
+                valueMax: 100,
+                valueStep: 1,
+                cluster: "msFormaldehyde",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT8 },
+                description: "Adjust formaldehyde ADC range",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "auto_clean_interval",
+                unit: "day",
+                valueMin: 0,
+                valueMax: 10,
+                valueStep: 1,
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0330, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Auto clean interval PM2.5 sensor",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "manual_clean",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0331, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Manual clean PM2.5 sensor",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "set_altitude",
+                unit: "meters",
+                valueMin: 0,
+                valueMax: 3000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0205, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Setting the altitude above sea level (for high accuracy of the CO2 sensor)",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "forced_recalibration",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0202, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Start FRC (Perform Forced Recalibration of the CO2 Sensor)",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "manual_forced_recalibration",
+                unit: "ppm",
+                valueMin: 0,
+                valueMax: 5000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0207, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Start Manual FRC (Perform Forced Recalibration of the CO2 Sensor)",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "automatic_self_calibration",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0402, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Automatic self calibration",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "factory_reset_co2",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0206, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Factory Reset CO2 sensor",
+                access: "STATE_SET",
+            }),
+        ],
+    },
+    {
+        zigbeeModel: ["EFEKTA_Air_Quality_Station_2o"],
+        model: "EFEKTA_Air_Quality_Station_2o",
+        vendor: "EFEKTA",
+        description: "EFEKTA Air Quality Station, PM0.5, PM1.0, PM2.5, PM4.0, PM10, PM Size, CO2, VOC Index, O3, Temperature, Humidity, TFT display 3.2 inches.",
+        extend: [
+            m.co2({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.numeric({
+                name: "pm1",
+                unit: "µg/m³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0601, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM1.0 (particulate matter) concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.pm25({
+                reporting: false,
+                access: "STATE",
+                description: "Measured PM2.5 (particulate matter) concentration",
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm4",
+                unit: "µg/m³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0605, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM4.0 (particulate matter) concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm10",
+                unit: "µg/m³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0602, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM10.0 (particulate matter) concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_size",
+                unit: "µm",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0603, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Typical Particle Size",
+                access: "STATE",
+                reporting: false,
+                precision: 2,
+            }),
+            m.numeric({
+                name: "pm_n05",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0640, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM0.5 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n1",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0641, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM1.0 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n25",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0642, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM2.5 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n4",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0643, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM4.0 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "pm_n10",
+                unit: "#/cm³",
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0644, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "Measured PM10.0 (particulate matter) number concentration",
+                access: "STATE",
+                reporting: false,
+                precision: 0,
+            }),
+            m.numeric({
+                name: "voc_index",
+                unit: "VOC Index points",
+                cluster: "genAnalogInput",
+                attribute: "presentValue",
+                description: "VOC index",
+                access: "STATE",
+                reporting: false,
+            }),
+            m.numeric({
+                name: "nox_index",
+                unit: "NOx Index points",
+                cluster: "genAnalogInput",
+                attribute: { ID: 0x0155, type: zigbee_herdsman_1.Zcl.DataType.SINGLE_PREC },
+                description: "NOx index",
+                access: "STATE",
+                reporting: false,
+            }),
+            m.numeric({
+                name: "ozone",
+                unit: "ppb",
+                cluster: "msOzone",
+                attribute: "measuredValue",
+                description: "Ozone concentration",
+                access: "STATE",
+                reporting: false,
+            }),
+            m.temperature({
+                description: "Measured value of the built-in temperature sensor",
+                reporting: false,
+                access: "STATE",
+            }),
+            m.humidity({
+                description: "Measured value of the built-in humidity sensor",
+                reporting: false,
+                access: "STATE",
+            }),
+            m.illuminance({
+                access: "STATE",
+                reporting: false,
+            }),
+            m.numeric({
+                name: "report_delay",
+                unit: "sec",
+                valueMin: 6,
+                valueMax: 600,
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0201, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Setting the sensor report delay. Setting the time in seconds (6-600), by default 15 seconds",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "auto_brightness",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0203, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Enable or Disable Auto Brightness of the Display",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "night_onoff_backlight",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0401, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Complete shutdown of the backlight at night mode",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "night_on_backlight",
+                unit: "Hr",
+                valueMin: 0,
+                valueMax: 23,
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0405, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Night mode activation time",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "night_off_backlight",
+                unit: "Hr",
+                valueMin: 0,
+                valueMax: 23,
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0406, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Night mode deactivation time",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "temperature_offset",
+                unit: "°C",
+                valueMin: -50,
+                valueMax: 50,
+                valueStep: 0.1,
+                scale: 10,
+                cluster: "msTemperatureMeasurement",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Adjust temperature",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "humidity_offset",
+                unit: "%",
+                valueMin: -50,
+                valueMax: 50,
+                valueStep: 1,
+                cluster: "msRelativeHumidity",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Adjust humidity",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "ozone_offset",
+                unit: "ppb",
+                valueMin: -100,
+                valueMax: 100,
+                valueStep: 1,
+                cluster: "msOzone",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Adjust ozone",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "auto_clean_interval",
+                unit: "day",
+                valueMin: 0,
+                valueMax: 10,
+                valueStep: 1,
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0330, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Auto clean interval PM2.5 sensor",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "manual_clean",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "pm25Measurement",
+                attribute: { ID: 0x0331, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Manual clean PM2.5 sensor",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "set_altitude",
+                unit: "meters",
+                valueMin: 0,
+                valueMax: 3000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0205, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Setting the altitude above sea level (for high accuracy of the CO2 sensor)",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "forced_recalibration",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0202, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Start FRC (Perform Forced Recalibration of the CO2 Sensor)",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "manual_forced_recalibration",
+                unit: "ppm",
+                valueMin: 0,
+                valueMax: 5000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0207, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Start Manual FRC (Perform Forced Recalibration of the CO2 Sensor)",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "automatic_self_calibration",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0402, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Automatic self calibration",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "factory_reset_co2",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0206, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Factory Reset CO2 sensor",
+                access: "STATE_SET",
+            }),
+        ],
+    },
+    {
+        zigbeeModel: ["EFEKTA_iAQ_S_I"],
+        model: "EFEKTA_iAQ_S_I",
+        vendor: "EFEKTA",
+        description: "CO2 Monitor with TFT Display, outdoor temperature and humidity, date and time",
+        extend: [
+            m.co2({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.temperature({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.humidity({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.illuminance({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.binary({
+                name: "auto_brightness",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0203, type: 0x10 },
+                description: "Enable or Disable Auto Brightness of the Display",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "night_onoff_backlight",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0401, type: 0x10 },
+                description: "Complete shutdown of the backlight at night mode",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "night_on_backlight",
+                unit: "Hr",
+                valueMin: 0,
+                valueMax: 23,
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0405, type: 0x20 },
+                description: "Night mode activation time",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "night_off_backlight",
+                unit: "Hr",
+                valueMin: 0,
+                valueMax: 23,
+                cluster: "msIlluminanceMeasurement",
+                attribute: { ID: 0x0406, type: 0x20 },
+                description: "Night mode deactivation time",
+                access: "STATE_SET",
+            }),
+            m.enumLookup({
+                name: "long_chart_period",
+                lookup: { "1H": 0, "24H": 1 },
+                cluster: "msCO2",
+                attribute: { ID: 0x0204, type: 0x10 },
+                description: "The period of plotting the CO2 level(OFF - 1H | ON - 24H)",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "set_altitude",
+                unit: "meters",
+                valueMin: 0,
+                valueMax: 3000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0205, type: 0x21 },
+                description: "Setting the altitude above sea level (for high accuracy of the CO2 sensor)",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "temperature_offset",
+                unit: "°C",
+                valueMin: -50,
+                valueMax: 50,
+                valueStep: 0.1,
+                scale: 10,
+                cluster: "msTemperatureMeasurement",
+                attribute: { ID: 0x0210, type: 0x29 },
+                description: "Adjust temperature",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "humidity_offset",
+                unit: "%",
+                valueMin: -50,
+                valueMax: 50,
+                valueStep: 1,
+                cluster: "msRelativeHumidity",
+                attribute: { ID: 0x0210, type: 0x29 },
+                description: "Adjust humidity",
+                access: "STATE_SET",
+            }),
+            m.enumLookup({
+                name: "th_sensor",
+                lookup: { INTERNAL: 0, EXTERNAL: 1 },
+                cluster: "msCO2",
+                attribute: { ID: 0x0288, type: 0x10 },
+                description: "Display data from internal or external TH sensor",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "automatic_scal",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0402, type: 0x10 },
+                description: "Automatic self calibration",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "forced_recalibration",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0202, type: 0x10 },
+                description: "Start FRC (Perform Forced Recalibration of the CO2 Sensor)",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "factory_reset_co2",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0206, type: 0x10 },
+                description: "Factory Reset CO2 sensor",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "manual_forced_recalibration",
+                unit: "ppm",
+                valueMin: 0,
+                valueMax: 5000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0207, type: 0x21 },
+                description: "Start Manual FRC (Perform Forced Recalibration of the CO2 Sensor)",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "enable_gas",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0220, type: 0x10 },
+                description: "Enable CO2 Gas Control",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "invert_logic_gas",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0225, type: 0x10 },
+                description: "Enable invert logic CO2 Gas Control",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "high_gas",
+                unit: "ppm",
+                valueMin: 400,
+                valueMax: 5000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0221, type: 0x21 },
+                description: "Setting High CO2 Gas Border",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "low_gas",
+                unit: "ppm",
+                valueMin: 400,
+                valueMax: 5000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0222, type: 0x21 },
+                description: "Setting Low CO2 Gas Border",
+                access: "STATE_SET",
+            }),
+        ],
+    },
+    {
+        zigbeeModel: ["EFEKTA_iAQ2_R2"],
+        model: "EFEKTA_iAQ2_R2",
+        vendor: "EFEKTA",
+        description: "CO2 and atmospheric pressure мonitor with IPS TFT Display, outdoor temperature and humidity",
+        extend: [
+            m.co2({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.temperature({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.humidity({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.pressure({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.illuminance({
+                reporting: false,
+                access: "STATE",
+            }),
+            m.binary({
+                name: "auto_brightness",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0203, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Enable or Disable Auto Brightness of the Display",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "night_onoff_backlight",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0401, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Complete shutdown of the backlight at night mode",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "night_on_backlight",
+                unit: "Hr",
+                valueMin: 0,
+                valueMax: 23,
+                cluster: "msCO2",
+                attribute: { ID: 0x0405, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Night mode activation time",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "night_off_backlight",
+                unit: "Hr",
+                valueMin: 0,
+                valueMax: 23,
+                cluster: "msCO2",
+                attribute: { ID: 0x0406, type: zigbee_herdsman_1.Zcl.DataType.UINT8 },
+                description: "Night mode deactivation time",
+                access: "STATE_SET",
+            }),
+            m.enumLookup({
+                name: "long_chart_period",
+                lookup: { "1H": 0, "24H": 1 },
+                cluster: "msCO2",
+                attribute: { ID: 0x0204, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "The period of plotting the CO2 level(OFF - 1H | ON - 24H)",
+                access: "STATE_SET",
+            }),
+            m.enumLookup({
+                name: "rotate",
+                lookup: { "0": 0, "90": 90, "180": 180, "270": 270 },
+                cluster: "msCO2",
+                attribute: { ID: 0x0285, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Display rotation angle",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "temperature_offset",
+                unit: "°C",
+                valueMin: -50,
+                valueMax: 50,
+                valueStep: 0.1,
+                scale: 10,
+                cluster: "msTemperatureMeasurement",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Adjust temperature",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "humidity_offset",
+                unit: "%",
+                valueMin: -50,
+                valueMax: 50,
+                valueStep: 1,
+                cluster: "msRelativeHumidity",
+                attribute: { ID: 0x0210, type: zigbee_herdsman_1.Zcl.DataType.INT16 },
+                description: "Adjust humidity",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "forced_recalibration",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0202, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Start FRC (Perform Forced Recalibration of the CO2 Sensor)",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "factory_reset_co2",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0206, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Factory Reset CO2 sensor",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "manual_forced_recalibration",
+                unit: "ppm",
+                valueMin: 0,
+                valueMax: 5000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0207, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Start Manual FRC (Perform Forced Recalibration of the CO2 Sensor)",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "enable_gas",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0220, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Enable CO2 Gas Control",
+                access: "STATE_SET",
+            }),
+            m.binary({
+                name: "invert_logic_gas",
+                valueOn: ["ON", 1],
+                valueOff: ["OFF", 0],
+                cluster: "msCO2",
+                attribute: { ID: 0x0225, type: zigbee_herdsman_1.Zcl.DataType.BOOLEAN },
+                description: "Enable invert logic CO2 Gas Control",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "high_gas",
+                unit: "ppm",
+                valueMin: 400,
+                valueMax: 5000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0221, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Setting High CO2 Gas Border",
+                access: "STATE_SET",
+            }),
+            m.numeric({
+                name: "low_gas",
+                unit: "ppm",
+                valueMin: 400,
+                valueMax: 5000,
+                cluster: "msCO2",
+                attribute: { ID: 0x0222, type: zigbee_herdsman_1.Zcl.DataType.UINT16 },
+                description: "Setting Low CO2 Gas Border",
+                access: "STATE_SET",
+            }),
+        ],
+    },
 ];
 //# sourceMappingURL=efekta.js.map