@tscircuit/props 0.0.683 → 0.0.685

package/README.md

@@ -565,14 +565,34 @@ export interface BreakoutPointProps extends Omit<
 ```ts
 export interface BusProps {
   name?: string;
+  /** Match these trace/port/bus/pair selectors as well as this element's members.
+   * maxLengthSkew applies to the combined members; no tolerance is inferred. */
+  lengthMatchTo?: string | string[];
+  /** Minimum/maximum pad-to-pad planar length for each member. Raw numbers are mm. */
+  minLength?: RouteLength;
+  maxLength?: RouteLength;
+  /** Nominal member length, absolute or relative to selected endpoints.
+   * Requires an explicit lengthTolerance, including zero for exact matching. */
+  targetLength?: RouteLength;
+  /** Allowed deviation above/below targetLength, in mm. */
+  lengthTolerance?: number | string;
+  /** Minimum centreline spacing between bus members, excluding declared pair partners.
+   * Raw numbers are mm; "3w" means three times the larger local trace width. */
+  pcbTraceSpacing?: TraceSpacing;
+  /** Minimum centreline spacing to traces outside this bus/pair (mm or e.g. "4w"). */
+  pcbSpacingToOtherSignals?: TraceSpacing;
+
   /** One or more trace names or port selectors for the connections in the bus. */
   connections: string[];
   /** If set, every trace in this bus is assigned to this autorouting phase. */
   routingPhaseIndex?: number | null;
   /** Maximum routed-length difference between bus members. Raw numbers are millimeters. */
   maxLengthSkew?: number | string;
-  /** Intended single-ended characteristic impedance. Raw numbers are ohms. */
-  targetImpedance?: number | string;
+  /** Intended single-ended impedance, e.g. "50±25ohm". Raw numbers are ohms. */
+  targetImpedance?: ImpedanceTarget;
+  /** Inclusive minimum/maximum acceptable impedance, in ohms. May be used without a nominal target. */
+  targetImpedanceMin?: number | string;
+  targetImpedanceMax?: number | string;
   /** Explicit PCB trace width for every bus member. Raw numbers are millimeters. */
   pcbTraceWidth?: number | string;
   /** PCB layers on which the bus may be routed. */
@@ -885,14 +905,31 @@ export interface RectCutoutProps extends Omit<
 ```ts
 export interface DifferentialPairProps {
   name?: string;
+  /** Match these trace/port/bus/pair selectors as well as this element's members.
+   * maxLengthSkew applies to the combined members; no tolerance is inferred. */
+  lengthMatchTo?: string | string[];
+  /** Minimum/maximum pad-to-pad planar length for each member. Raw numbers are mm. */
+  minLength?: RouteLength;
+  maxLength?: RouteLength;
+  /** Nominal member length, absolute or relative to selected endpoints.
+   * Requires an explicit lengthTolerance, including zero for exact matching. */
+  targetLength?: RouteLength;
+  /** Allowed deviation above/below targetLength, in mm. */
+  lengthTolerance?: number | string;
+  /** Minimum centreline spacing to traces outside this bus/pair (mm or e.g. "4w"). */
+  pcbSpacingToOtherSignals?: TraceSpacing;
+
   /** Name of the trace or pin carrying the positive signal. */
   positiveConnection: string;
   /** Name of the trace or pin carrying the negative signal. */
   negativeConnection: string;
   /** Maximum permitted routed-length skew. Raw numbers are millimeters. */
   maxLengthSkew?: number | string;
-  /** Intended differential characteristic impedance. Raw numbers are ohms. */
-  targetDifferentialImpedance?: number | string;
+  /** Intended differential impedance, e.g. "100±10ohm". Raw numbers are ohms. */
+  targetDifferentialImpedance?: ImpedanceTarget;
+  /** Inclusive minimum/maximum acceptable impedance, in ohms. May be used without a nominal target. */
+  targetDifferentialImpedanceMin?: number | string;
+  targetDifferentialImpedanceMax?: number | string;
   /** Edge-to-edge PCB copper gap between the pair. Raw numbers are millimeters. */
   pcbTraceGap?: number | string;
   /** Maximum length over which the pair may be routed without coupling. Raw numbers are millimeters. */