@tscircuit/props 0.0.666 → 0.0.668

package/lib/common/fanoutTracePath.ts

@@ -13,6 +13,10 @@ const routePoint = z.discriminatedUnion("route_type", [
     x: coordinate,
     y: coordinate,
     width: positiveDistance,
+    width_interpolation_mode: z
+      .enum(["linear", "quadratic"])
+      .optional()
+      .describe("Interpolate width from this point to the next wire point."),
     layer: layer_ref,
   }),
   z.object({
@@ -31,6 +35,10 @@ const routePoint = z.discriminatedUnion("route_type", [
  * fanout's local PCB frame, in mm: +X right, +Y up, right-handed with +Z
  * above the board. They are points (placement adds translation), not
  * directions. Numeric distances are mm; unit strings are parsed to mm.
+ * A wire point's optional width_interpolation_mode interpolates its width to
+ * the next wire point's width. Omitted means the existing constant-width
+ * behavior; there are no aliases or migration requirements. Interpolation
+ * cannot terminate at a via directly: put a wire point at the via position.
  * Layers are physical board layers, independent of placement. Either endpoint
  * may be a via: the initial layer is its from_layer and the final layer is its
  * to_layer. Placement legality (including allowViaInPad) is checked by core,
@@ -44,7 +52,22 @@ export const fanoutTracePath = z.object({
     .superRefine((route, ctx) => {
       const first = route[0]
       let layer = first?.route_type === "via" ? first.from_layer : first?.layer
-      for (const point of route) {
+      for (const [index, point] of route.entries()) {
+        if (point.route_type === "wire" && point.width_interpolation_mode) {
+          const next = route[index + 1]
+          if (
+            next?.route_type !== "wire" ||
+            next.layer !== point.layer ||
+            (next.x === point.x && next.y === point.y)
+          ) {
+            ctx.addIssue({
+              code: "custom",
+              path: [index, "width_interpolation_mode"],
+              message:
+                "Width interpolation requires a distinct next wire point on the same layer",
+            })
+          }
+        }
         if (
           (point.route_type === "wire" ? point.layer : point.from_layer) !==
           layer

package/lib/components/group.ts

@@ -321,6 +321,12 @@ export interface RoutingTolerances {
   minViaHoleEdgeToViaHoleEdgeClearance?: Distance
   minPlatedHoleDrillEdgeToDrillEdgeClearance?: Distance
   minTraceToPadEdgeClearance?: Distance
+  /**
+   * Minimum trace copper edge to non-plated hole edge clearance. Numbers are mm;
+   * unit strings are normalized to mm. Must be finite and non-negative. Omitted
+   * leaves the router default unchanged. Independent of pad clearance, with no aliases.
+   */
+  minTraceToHoleEdgeClearance?: Distance
   minPadEdgeToPadEdgeClearance?: Distance
   minBoardEdgeClearance?: Distance
   minViaEdgeToPadEdgeClearance?: Distance
@@ -402,6 +408,11 @@ export const routingTolerances = z.object({
   minViaEdgeToPadEdgeClearance: length.optional(),
   minPlatedHoleDrillEdgeToDrillEdgeClearance: length.optional(),
   minTraceToPadEdgeClearance: length.optional(),
+  minTraceToHoleEdgeClearance: length
+    .refine((value) => Number.isFinite(value) && value >= 0, {
+      message: "minTraceToHoleEdgeClearance must be finite and non-negative",
+    })
+    .optional(),
   minPadEdgeToPadEdgeClearance: length.optional(),
   minBoardEdgeClearance: length.optional(),
   minViaHoleDiameter: length.optional(),

package/lib/components/trace.ts

@@ -22,6 +22,15 @@ const baseTraceProps = z.object({
   width: distance.optional().describe("Alias for trace thickness"),
   schematicRouteHints: z.array(point).optional(),
   pcbRouteHints: z.array(route_hint_point).optional(),
+  pcbTeardrops: z.boolean().optional().describe("Enable PCB trace teardrops."),
+  pcbTeardropStart: z
+    .boolean()
+    .optional()
+    .describe("Teardrop at the start (from) of trace"),
+  pcbTeardropEnd: z
+    .boolean()
+    .optional()
+    .describe("Teardrop at the end (to) of trace"),
   pcbPathRelativeTo: z.string().optional(),
   pcbPath: pcbPath.optional(),
   pcbPaths: z.array(pcbPath).optional(),

package/package.json

@@ -1,6 +1,6 @@
 {
   "name": "@tscircuit/props",
-  "version": "0.0.666",
+  "version": "0.0.668",
   "description": "Props for tscircuit builtin component types",
   "main": "dist/index.js",
   "type": "module",