@theerapat-s28/ts-structural-eng-tools 1.4.0 → 1.5.0

package/README.md

@@ -65,7 +65,8 @@ src/
 ├── strengthening/        # Strengthening methods
 │   ├── index.ts
 │   ├── rc-beam-steel-plate-jacketing.ts   # Moment capacity before/after plate jacketing
-│   └── rc-beam-plate-interface-bolts.ts  # Interface shear flow and required interface bolts
+│   ├── rc-beam-plate-interface-bolts.ts  # Interface shear flow and required interface bolts
+│   └── rc-beam-side-plate-shear.ts       # Shear capacity before/after bolted side plates (two models)
 ├── core/                 # Shared infrastructure
 │   ├── index.ts
 │   ├── constants/        # RC design constants (ACI 318)
@@ -125,6 +126,14 @@ Summarised below; see the [full API reference](https://theerapat-s28.github.io/t
 
 Both plates are independently optional: a plate counts as present only when its width and thickness are both positive, so the same functions cover a bottom-only jacket and a top-and-bottom jacket. Use `hasTopPlate(props)` / `hasBottomPlate(props)` to test for presence.
 
+Plates bolted to the sides of the web strengthen the beam in shear instead. ACI 318-19 has no provisions for steel side plates, so two independent models are offered and both return a `before` / `after` pair of `phiVn` (kN) for a continuous plate or discrete strips, with the plate contribution limited by the bolt anchorage and by the ACI 318-19 22.5.1.2 web-crushing cap. Use `hasSidePlate(props)` to test for presence.
+
+- **`sidePlateShearCapacityByWebYielding(section, plates)`** — Takes each plate as a supplementary web reaching the von Mises shear yield stress `0.6·fy` (AISC 360 G2.1), and warns on plate slenderness beyond `2.24·√(Es/fy)`.
+- **`sidePlateShearCapacityByTensionTie(section, plates)`** — Takes each plate as a tension tie crossing the diagonal crack, per the bonded shear reinforcement model of ACI 440.2R-17 §11.4 with steel in place of FRP: `ffe = min(fy, Es·0.004)` and `psi_f = 0.85`. Supports inclined strips.
+
+ACI 440.2R-17 11.4.2 (spacing, which defers to the ACI 318 limits) and 11.4.3 (`Vs + Vf ≤ 0.66·√f'c·bw·d`) are verified against the guide; the subsections carrying the 0.004 strain cap and `psi_f` are still cited at §11.4 only. See the citation-status note at the top of `src/strengthening/rc-beam-side-plate-shear.ts`.
+- **`compareSidePlateShearCapacity(section, plates)`** — Runs both models and reports the lower `phiVn` as `governing`; the intended entry point for a conservative design capacity.
+
 ### General Utilities
 
 - **`concreteBeta(fc_)`** — ACI 318 β₁ factor

package/dist/core/constants/rc.constant.d.ts

@@ -22,4 +22,11 @@ export declare const ANCHOR_STEEL_SHEAR_COEFFICIENT = 0.6;
 export declare const ANCHOR_FUTA_FYA_FACTOR = 1.9;
 export declare const MAX_ANCHOR_FUTA = 860;
 export declare const MIN_ANCHOR_SPACING_DIAMETER_FACTOR = 4;
+export declare const DEFAULT_PLATE_ELASTIC_MODULUS = 200000;
+export declare const PLATE_SHEAR_YIELD_COEFFICIENT = 0.6;
+export declare const PLATE_SHEAR_SLENDERNESS_COEFFICIENT = 2.24;
+export declare const SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT = 0.004;
+export declare const SIDE_PLATE_REDUCTION_FACTOR_PSI = 0.85;
+export declare const DEFAULT_SIDE_PLATE_SIDES = 2;
+export declare const DEFAULT_SIDE_PLATE_ANGLE = 90;
 export declare const MAX_PLATE_BOLT_SPACING = 300;

package/dist/core/constants/rc.constant.js

@@ -1,6 +1,6 @@
 "use strict";
 Object.defineProperty(exports, "__esModule", { value: true });
-exports.MAX_PLATE_BOLT_SPACING = exports.MIN_ANCHOR_SPACING_DIAMETER_FACTOR = exports.MAX_ANCHOR_FUTA = exports.ANCHOR_FUTA_FYA_FACTOR = exports.ANCHOR_STEEL_SHEAR_COEFFICIENT = exports.ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR = exports.MIN_AV_ABSOLUTE_COEFFICIENT = exports.MIN_AV_SQRT_FC_COEFFICIENT = exports.MAX_STIRRUP_SPACING_HIGH_VS_DEPTH_FACTOR = exports.MAX_STIRRUP_SPACING_HIGH_VS = exports.MAX_STIRRUP_SPACING_LOW_VS_DEPTH_FACTOR = exports.MAX_STIRRUP_SPACING_LOW_VS = exports.VS_SPACING_THRESHOLD_COEFFICIENT = exports.MAX_VS_COEFFICIENT = exports.SQRT_FC_SHEAR_LIMIT = exports.CONCRETE_SHEAR_VC_COEFFICIENT = exports.SHEAR_STRENGTH_REDUCTION_FACTOR = exports.MIN_LAYER_CLEAR_SPACING = exports.AGGREGATE_SPACING_FACTOR = exports.MIN_BAR_CLEAR_SPACING = exports.DEFAULT_MAX_AGGREGATE_SIZE = exports.DEFAULT_STIRRUP_DIAMETER = exports.DEFAULT_BEAM_COVER = exports.CONCRETE_ULTIMATE_STRAIN = exports.FLEXURAL_STRENGTH_REDUCTION_FACTOR = void 0;
+exports.MAX_PLATE_BOLT_SPACING = exports.DEFAULT_SIDE_PLATE_ANGLE = exports.DEFAULT_SIDE_PLATE_SIDES = exports.SIDE_PLATE_REDUCTION_FACTOR_PSI = exports.SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT = exports.PLATE_SHEAR_SLENDERNESS_COEFFICIENT = exports.PLATE_SHEAR_YIELD_COEFFICIENT = exports.DEFAULT_PLATE_ELASTIC_MODULUS = exports.MIN_ANCHOR_SPACING_DIAMETER_FACTOR = exports.MAX_ANCHOR_FUTA = exports.ANCHOR_FUTA_FYA_FACTOR = exports.ANCHOR_STEEL_SHEAR_COEFFICIENT = exports.ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR = exports.MIN_AV_ABSOLUTE_COEFFICIENT = exports.MIN_AV_SQRT_FC_COEFFICIENT = exports.MAX_STIRRUP_SPACING_HIGH_VS_DEPTH_FACTOR = exports.MAX_STIRRUP_SPACING_HIGH_VS = exports.MAX_STIRRUP_SPACING_LOW_VS_DEPTH_FACTOR = exports.MAX_STIRRUP_SPACING_LOW_VS = exports.VS_SPACING_THRESHOLD_COEFFICIENT = exports.MAX_VS_COEFFICIENT = exports.SQRT_FC_SHEAR_LIMIT = exports.CONCRETE_SHEAR_VC_COEFFICIENT = exports.SHEAR_STRENGTH_REDUCTION_FACTOR = exports.MIN_LAYER_CLEAR_SPACING = exports.AGGREGATE_SPACING_FACTOR = exports.MIN_BAR_CLEAR_SPACING = exports.DEFAULT_MAX_AGGREGATE_SIZE = exports.DEFAULT_STIRRUP_DIAMETER = exports.DEFAULT_BEAM_COVER = exports.CONCRETE_ULTIMATE_STRAIN = exports.FLEXURAL_STRENGTH_REDUCTION_FACTOR = void 0;
 exports.FLEXURAL_STRENGTH_REDUCTION_FACTOR = 0.9;
 exports.CONCRETE_ULTIMATE_STRAIN = 0.003;
 // ACI 318-19 Table 20.6.1.3.1: cast-in-place beams, not exposed to weather or in contact with ground
@@ -41,6 +41,25 @@ exports.ANCHOR_FUTA_FYA_FACTOR = 1.9;
 exports.MAX_ANCHOR_FUTA = 860; // MPa
 // ACI 318-19 17.9.2: min center-to-center spacing of cast-in anchors = 4 * da
 exports.MIN_ANCHOR_SPACING_DIAMETER_FACTOR = 4;
+// Default elastic modulus of structural steel plate, used when the plate props omit Es
+exports.DEFAULT_PLATE_ELASTIC_MODULUS = 200000; // MPa
+// AISC 360 G2.1 / von Mises: shear yield stress of a steel web = 0.6 * Fy
+exports.PLATE_SHEAR_YIELD_COEFFICIENT = 0.6;
+// AISC 360 G2.1(a): a web of slenderness h/tw <= 2.24*sqrt(E/Fy) reaches shear
+// yielding before shear buckling
+exports.PLATE_SHEAR_SLENDERNESS_COEFFICIENT = 2.24; // * sqrt(Es / fy)
+// ACI 440.2R-17, 11.4: effective strain in bonded shear reinforcement is capped
+// to preserve aggregate interlock in the concrete. Subsection unverified — see the
+// TODO in strengthening/rc-beam-side-plate-shear.ts.
+exports.SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT = 0.004;
+// ACI 440.2R-17, 11.4: additional reduction factor psi_f for two-sided bonded
+// shear strengthening (not fully wrapped). Subsection unverified — see the TODO in
+// strengthening/rc-beam-side-plate-shear.ts.
+exports.SIDE_PLATE_REDUCTION_FACTOR_PSI = 0.85;
+// Both faces of the web plated, unless the caller says otherwise
+exports.DEFAULT_SIDE_PLATE_SIDES = 2;
+// Vertical strips, unless the caller gives an inclination
+exports.DEFAULT_SIDE_PLATE_ANGLE = 90; // degrees from the beam axis
 // Practical detailing limit on bolt pitch along a bonded strengthening plate,
 // so the plate is restrained against local buckling / peeling between fasteners
 exports.MAX_PLATE_BOLT_SPACING = 300; // mm

package/dist/core/constants/rc.constant.js.map

@@ -1 +1 @@
-{"version":3,"file":"rc.constant.js","sourceRoot":"","sources":["../../../src/core/constants/rc.constant.ts"],"names":[],"mappings":";;;AAAa,QAAA,kCAAkC,GAAG,GAAG,CAAC;AACzC,QAAA,wBAAwB,GAAG,KAAK,CAAC;AAE9C,qGAAqG;AACxF,QAAA,kBAAkB,GAAG,EAAE,CAAC,CAAC,6BAA6B;AACtD,QAAA,wBAAwB,GAAG,EAAE,CAAC,CAAC,KAAK;AACpC,QAAA,0BAA0B,GAAG,EAAE,CAAC,CAAC,iCAAiC;AAE/E,wEAAwE;AAC3D,QAAA,qBAAqB,GAAG,EAAE,CAAC,CAAC,KAAK;AACjC,QAAA,wBAAwB,GAAG,CAAC,GAAG,CAAC,CAAC;AAE9C,uDAAuD;AAC1C,QAAA,uBAAuB,GAAG,EAAE,CAAC,CAAC,KAAK;AAEhD,yDAAyD;AAC5C,QAAA,+BAA+B,GAAG,IAAI,CAAC;AAEpD,kFAAkF;AACrE,QAAA,6BAA6B,GAAG,IAAI,CAAC;AAElD,gFAAgF;AAChF,6DAA6D;AAChD,QAAA,mBAAmB,GAAG,GAAG,CAAC,CAAC,MAAM;AAE9C,qEAAqE;AACxD,QAAA,kBAAkB,GAAG,IAAI,CAAC;AAEvC,yFAAyF;AAC5E,QAAA,gCAAgC,GAAG,IAAI,CAAC,CAAC,uBAAuB;AAE7E,6EAA6E;AAChE,QAAA,0BAA0B,GAAG,GAAG,CAAC,CAAC,KAAK;AACvC,QAAA,uCAAuC,GAAG,GAAG,CAAC,CAAC,MAAM;AAElE,4EAA4E;AAC/D,QAAA,2BAA2B,GAAG,GAAG,CAAC,CAAC,KAAK;AACxC,QAAA,wCAAwC,GAAG,IAAI,CAAC,CAAC,MAAM;AAEpE,0FAA0F;AAC7E,QAAA,0BAA0B,GAAG,KAAK,CAAC;AACnC,QAAA,2BAA2B,GAAG,IAAI,CAAC;AAEhD,+EAA+E;AAClE,QAAA,sCAAsC,GAAG,IAAI,CAAC;AAE3D,iDAAiD;AACpC,QAAA,8BAA8B,GAAG,GAAG,CAAC;AAElD,qEAAqE;AACxD,QAAA,sBAAsB,GAAG,GAAG,CAAC;AAC7B,QAAA,eAAe,GAAG,GAAG,CAAC,CAAC,MAAM;AAE1C,8EAA8E;AACjE,QAAA,kCAAkC,GAAG,CAAC,CAAC;AAEpD,8EAA8E;AAC9E,gFAAgF;AACnE,QAAA,sBAAsB,GAAG,GAAG,CAAC,CAAC,KAAK"}
+{"version":3,"file":"rc.constant.js","sourceRoot":"","sources":["../../../src/core/constants/rc.constant.ts"],"names":[],"mappings":";;;AAAa,QAAA,kCAAkC,GAAG,GAAG,CAAC;AACzC,QAAA,wBAAwB,GAAG,KAAK,CAAC;AAE9C,qGAAqG;AACxF,QAAA,kBAAkB,GAAG,EAAE,CAAC,CAAC,6BAA6B;AACtD,QAAA,wBAAwB,GAAG,EAAE,CAAC,CAAC,KAAK;AACpC,QAAA,0BAA0B,GAAG,EAAE,CAAC,CAAC,iCAAiC;AAE/E,wEAAwE;AAC3D,QAAA,qBAAqB,GAAG,EAAE,CAAC,CAAC,KAAK;AACjC,QAAA,wBAAwB,GAAG,CAAC,GAAG,CAAC,CAAC;AAE9C,uDAAuD;AAC1C,QAAA,uBAAuB,GAAG,EAAE,CAAC,CAAC,KAAK;AAEhD,yDAAyD;AAC5C,QAAA,+BAA+B,GAAG,IAAI,CAAC;AAEpD,kFAAkF;AACrE,QAAA,6BAA6B,GAAG,IAAI,CAAC;AAElD,gFAAgF;AAChF,6DAA6D;AAChD,QAAA,mBAAmB,GAAG,GAAG,CAAC,CAAC,MAAM;AAE9C,qEAAqE;AACxD,QAAA,kBAAkB,GAAG,IAAI,CAAC;AAEvC,yFAAyF;AAC5E,QAAA,gCAAgC,GAAG,IAAI,CAAC,CAAC,uBAAuB;AAE7E,6EAA6E;AAChE,QAAA,0BAA0B,GAAG,GAAG,CAAC,CAAC,KAAK;AACvC,QAAA,uCAAuC,GAAG,GAAG,CAAC,CAAC,MAAM;AAElE,4EAA4E;AAC/D,QAAA,2BAA2B,GAAG,GAAG,CAAC,CAAC,KAAK;AACxC,QAAA,wCAAwC,GAAG,IAAI,CAAC,CAAC,MAAM;AAEpE,0FAA0F;AAC7E,QAAA,0BAA0B,GAAG,KAAK,CAAC;AACnC,QAAA,2BAA2B,GAAG,IAAI,CAAC;AAEhD,+EAA+E;AAClE,QAAA,sCAAsC,GAAG,IAAI,CAAC;AAE3D,iDAAiD;AACpC,QAAA,8BAA8B,GAAG,GAAG,CAAC;AAElD,qEAAqE;AACxD,QAAA,sBAAsB,GAAG,GAAG,CAAC;AAC7B,QAAA,eAAe,GAAG,GAAG,CAAC,CAAC,MAAM;AAE1C,8EAA8E;AACjE,QAAA,kCAAkC,GAAG,CAAC,CAAC;AAEpD,uFAAuF;AAC1E,QAAA,6BAA6B,GAAG,MAAM,CAAC,CAAC,MAAM;AAE3D,0EAA0E;AAC7D,QAAA,6BAA6B,GAAG,GAAG,CAAC;AAEjD,+EAA+E;AAC/E,iCAAiC;AACpB,QAAA,mCAAmC,GAAG,IAAI,CAAC,CAAC,kBAAkB;AAE3E,gFAAgF;AAChF,mFAAmF;AACnF,qDAAqD;AACxC,QAAA,iCAAiC,GAAG,KAAK,CAAC;AAEvD,8EAA8E;AAC9E,mFAAmF;AACnF,6CAA6C;AAChC,QAAA,+BAA+B,GAAG,IAAI,CAAC;AAEpD,iEAAiE;AACpD,QAAA,wBAAwB,GAAG,CAAC,CAAC;AAE1C,0DAA0D;AAC7C,QAAA,wBAAwB,GAAG,EAAE,CAAC,CAAC,6BAA6B;AAEzE,8EAA8E;AAC9E,gFAAgF;AACnE,QAAA,sBAAsB,GAAG,GAAG,CAAC,CAAC,KAAK"}

package/dist/core/errors/rc-design.error.js

@@ -56,5 +56,13 @@ exports.Errors = {
         code: 204,
         message: "No valid cracked neutral axis was found within the concrete depth; check the section and plate properties.",
     },
+    SIDE_PLATE_GEOMETRY_INVALID: {
+        code: 205,
+        message: "Inconsistent side plate geometry; thickness, engaged depth, fy and sides must be positive, the depth must fit within the section, and a stripped layout requires a positive width and spacing.",
+    },
+    STRENGTHENED_SHEAR_NO_HEADROOM: {
+        code: 206,
+        message: "Existing Vs already reaches 0.66*sqrt(fc')*bw*d (ACI318-19, 22.5.1.2); the web crushes before any added side plate force can be developed, so shear strengthening cannot be realised on this section.",
+    },
 };
 //# sourceMappingURL=rc-design.error.js.map

package/dist/core/errors/rc-design.error.js.map

@@ -1 +1 @@
-{"version":3,"file":"rc-design.error.js","sourceRoot":"","sources":["../../../src/core/errors/rc-design.error.ts"],"names":[],"mappings":";;;AAAA,MAAa,aAAc,SAAQ,KAAK;IAItC,YAAY,MAAyB,EAAE,IAAI,EAAE,CAAC,EAAE,OAAO,EAAE,eAAe,EAAE;QACxE,KAAK,CAAC,GAAG,CAAC,OAAO,CAAC,CAAC;QACnB,IAAI,CAAC,IAAI,GAAG,GAAG,CAAC,IAAI,CAAC;QACrB,IAAI,CAAC,OAAO,GAAG,GAAG,CAAC,OAAO,CAAC;QAC3B,MAAM,CAAC,cAAc,CAAC,IAAI,EAAE,aAAa,CAAC,SAAS,CAAC,CAAC;IACvD,CAAC;CACF;AAVD,sCAUC;AAOY,QAAA,MAAM,GAAsC;IACvD,8BAA8B;IAE9B;;;;;;OAMG;IACH,2BAA2B,EAAE;QAC3B,IAAI,EAAE,GAAG;QACT,OAAO,EAAE,sFAAsF;KAChG;IACD,0BAA0B,EAAE;QAC1B,IAAI,EAAE,GAAG;QACT,OAAO,EAAE,kEAAkE;KAC5E;IACD,0BAA0B,EAAE;QAC1B,IAAI,EAAE,GAAG;QACT,OAAO,EACL,4GAA4G;KAC/G;IACD,iCAAiC,EAAE;QACjC,IAAI,EAAE,GAAG;QACT,OAAO,EAAE,mEAAmE;KAC7E;IACD,0BAA0B,EAAE;QAC1B,IAAI,EAAE,GAAG;QACT,OAAO,EACL,yGAAyG;KAC5G;IAED,4DAA4D;IAC5D,uBAAuB,EAAE;QACvB,IAAI,EAAE,GAAG;QACT,OAAO,EACL,6GAA6G;KAChH;IACD,qBAAqB,EAAE;QACrB,IAAI,EAAE,GAAG;QACT,OAAO,EACL,kGAAkG;KACrG;IACD,qBAAqB,EAAE;QACrB,IAAI,EAAE,GAAG;QACT,OAAO,EACL,gHAAgH;KACnH;IACD,oBAAoB,EAAE;QACpB,IAAI,EAAE,GAAG;QACT,OAAO,EACL,4GAA4G;KAC/G;CACF,CAAC"}
+{"version":3,"file":"rc-design.error.js","sourceRoot":"","sources":["../../../src/core/errors/rc-design.error.ts"],"names":[],"mappings":";;;AAAA,MAAa,aAAc,SAAQ,KAAK;IAItC,YAAY,MAAyB,EAAE,IAAI,EAAE,CAAC,EAAE,OAAO,EAAE,eAAe,EAAE;QACxE,KAAK,CAAC,GAAG,CAAC,OAAO,CAAC,CAAC;QACnB,IAAI,CAAC,IAAI,GAAG,GAAG,CAAC,IAAI,CAAC;QACrB,IAAI,CAAC,OAAO,GAAG,GAAG,CAAC,OAAO,CAAC;QAC3B,MAAM,CAAC,cAAc,CAAC,IAAI,EAAE,aAAa,CAAC,SAAS,CAAC,CAAC;IACvD,CAAC;CACF;AAVD,sCAUC;AAOY,QAAA,MAAM,GAAsC;IACvD,8BAA8B;IAE9B;;;;;;OAMG;IACH,2BAA2B,EAAE;QAC3B,IAAI,EAAE,GAAG;QACT,OAAO,EAAE,sFAAsF;KAChG;IACD,0BAA0B,EAAE;QAC1B,IAAI,EAAE,GAAG;QACT,OAAO,EAAE,kEAAkE;KAC5E;IACD,0BAA0B,EAAE;QAC1B,IAAI,EAAE,GAAG;QACT,OAAO,EACL,4GAA4G;KAC/G;IACD,iCAAiC,EAAE;QACjC,IAAI,EAAE,GAAG;QACT,OAAO,EAAE,mEAAmE;KAC7E;IACD,0BAA0B,EAAE;QAC1B,IAAI,EAAE,GAAG;QACT,OAAO,EACL,yGAAyG;KAC5G;IAED,4DAA4D;IAC5D,uBAAuB,EAAE;QACvB,IAAI,EAAE,GAAG;QACT,OAAO,EACL,6GAA6G;KAChH;IACD,qBAAqB,EAAE;QACrB,IAAI,EAAE,GAAG;QACT,OAAO,EACL,kGAAkG;KACrG;IACD,qBAAqB,EAAE;QACrB,IAAI,EAAE,GAAG;QACT,OAAO,EACL,gHAAgH;KACnH;IACD,oBAAoB,EAAE;QACpB,IAAI,EAAE,GAAG;QACT,OAAO,EACL,4GAA4G;KAC/G;IACD,2BAA2B,EAAE;QAC3B,IAAI,EAAE,GAAG;QACT,OAAO,EACL,gMAAgM;KACnM;IACD,8BAA8B,EAAE;QAC9B,IAAI,EAAE,GAAG;QACT,OAAO,EACL,uMAAuM;KAC1M;CACF,CAAC"}

package/dist/core/index.d.ts

@@ -1,8 +1,8 @@
 export type { RectBeamSection, RectSinglyBeamSection, RectDoublyBeamSection, RectShearSection, StirrupShearSection, ShearReinforcementCheckInput, RebarGroupInput, RectBeamBarLayoutInput, } from "./types/rc-beam.type";
 export { isSinglyReinforced } from "./types/rc-beam.type";
-export type { SteelJacketedProps, SectionState, PlateShearFlowInput, BoltProps, PlateInterfaceBoltInput, } from "./types/plate-jacketing.type";
-export { hasTopPlate, hasBottomPlate } from "./types/plate-jacketing.type";
+export type { SteelJacketedProps, SectionState, PlateShearFlowInput, BoltProps, PlateInterfaceBoltInput, SidePlateConfiguration, SidePlateAnchorage, SidePlateShearProps, } from "./types/plate-jacketing.type";
+export { hasTopPlate, hasBottomPlate, hasSidePlate } from "./types/plate-jacketing.type";
 export type { Warnings, calculationResult } from "./types/output-message.type";
 export type { unit } from "./types/unit.type";
-export { FLEXURAL_STRENGTH_REDUCTION_FACTOR, CONCRETE_ULTIMATE_STRAIN, SHEAR_STRENGTH_REDUCTION_FACTOR, ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR, MAX_PLATE_BOLT_SPACING, } from "./constants/rc.constant";
+export { FLEXURAL_STRENGTH_REDUCTION_FACTOR, CONCRETE_ULTIMATE_STRAIN, SHEAR_STRENGTH_REDUCTION_FACTOR, ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR, MAX_PLATE_BOLT_SPACING, PLATE_SHEAR_YIELD_COEFFICIENT, SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT, SIDE_PLATE_REDUCTION_FACTOR_PSI, } from "./constants/rc.constant";
 export { RCDesignError, Errors } from "./errors/rc-design.error";

package/dist/core/index.js

@@ -1,11 +1,12 @@
 "use strict";
 Object.defineProperty(exports, "__esModule", { value: true });
-exports.Errors = exports.RCDesignError = exports.MAX_PLATE_BOLT_SPACING = exports.ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR = exports.SHEAR_STRENGTH_REDUCTION_FACTOR = exports.CONCRETE_ULTIMATE_STRAIN = exports.FLEXURAL_STRENGTH_REDUCTION_FACTOR = exports.hasBottomPlate = exports.hasTopPlate = exports.isSinglyReinforced = void 0;
+exports.Errors = exports.RCDesignError = exports.SIDE_PLATE_REDUCTION_FACTOR_PSI = exports.SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT = exports.PLATE_SHEAR_YIELD_COEFFICIENT = exports.MAX_PLATE_BOLT_SPACING = exports.ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR = exports.SHEAR_STRENGTH_REDUCTION_FACTOR = exports.CONCRETE_ULTIMATE_STRAIN = exports.FLEXURAL_STRENGTH_REDUCTION_FACTOR = exports.hasSidePlate = exports.hasBottomPlate = exports.hasTopPlate = exports.isSinglyReinforced = void 0;
 var rc_beam_type_1 = require("./types/rc-beam.type");
 Object.defineProperty(exports, "isSinglyReinforced", { enumerable: true, get: function () { return rc_beam_type_1.isSinglyReinforced; } });
 var plate_jacketing_type_1 = require("./types/plate-jacketing.type");
 Object.defineProperty(exports, "hasTopPlate", { enumerable: true, get: function () { return plate_jacketing_type_1.hasTopPlate; } });
 Object.defineProperty(exports, "hasBottomPlate", { enumerable: true, get: function () { return plate_jacketing_type_1.hasBottomPlate; } });
+Object.defineProperty(exports, "hasSidePlate", { enumerable: true, get: function () { return plate_jacketing_type_1.hasSidePlate; } });
 // Constants
 var rc_constant_1 = require("./constants/rc.constant");
 Object.defineProperty(exports, "FLEXURAL_STRENGTH_REDUCTION_FACTOR", { enumerable: true, get: function () { return rc_constant_1.FLEXURAL_STRENGTH_REDUCTION_FACTOR; } });
@@ -13,6 +14,9 @@ Object.defineProperty(exports, "CONCRETE_ULTIMATE_STRAIN", { enumerable: true, g
 Object.defineProperty(exports, "SHEAR_STRENGTH_REDUCTION_FACTOR", { enumerable: true, get: function () { return rc_constant_1.SHEAR_STRENGTH_REDUCTION_FACTOR; } });
 Object.defineProperty(exports, "ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR", { enumerable: true, get: function () { return rc_constant_1.ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR; } });
 Object.defineProperty(exports, "MAX_PLATE_BOLT_SPACING", { enumerable: true, get: function () { return rc_constant_1.MAX_PLATE_BOLT_SPACING; } });
+Object.defineProperty(exports, "PLATE_SHEAR_YIELD_COEFFICIENT", { enumerable: true, get: function () { return rc_constant_1.PLATE_SHEAR_YIELD_COEFFICIENT; } });
+Object.defineProperty(exports, "SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT", { enumerable: true, get: function () { return rc_constant_1.SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT; } });
+Object.defineProperty(exports, "SIDE_PLATE_REDUCTION_FACTOR_PSI", { enumerable: true, get: function () { return rc_constant_1.SIDE_PLATE_REDUCTION_FACTOR_PSI; } });
 // Errors
 var rc_design_error_1 = require("./errors/rc-design.error");
 Object.defineProperty(exports, "RCDesignError", { enumerable: true, get: function () { return rc_design_error_1.RCDesignError; } });

package/dist/core/index.js.map

@@ -1 +1 @@
-{"version":3,"file":"index.js","sourceRoot":"","sources":["../../src/core/index.ts"],"names":[],"mappings":";;;AAWA,qDAA0D;AAAjD,kHAAA,kBAAkB,OAAA;AAQ3B,qEAA2E;AAAlE,mHAAA,WAAW,OAAA;AAAE,sHAAA,cAAc,OAAA;AAIpC,YAAY;AACZ,uDAMiC;AAL/B,iIAAA,kCAAkC,OAAA;AAClC,uHAAA,wBAAwB,OAAA;AACxB,8HAAA,+BAA+B,OAAA;AAC/B,qIAAA,sCAAsC,OAAA;AACtC,qHAAA,sBAAsB,OAAA;AAGxB,SAAS;AACT,4DAAiE;AAAxD,gHAAA,aAAa,OAAA;AAAE,yGAAA,MAAM,OAAA"}
+{"version":3,"file":"index.js","sourceRoot":"","sources":["../../src/core/index.ts"],"names":[],"mappings":";;;AAWA,qDAA0D;AAAjD,kHAAA,kBAAkB,OAAA;AAW3B,qEAAyF;AAAhF,mHAAA,WAAW,OAAA;AAAE,sHAAA,cAAc,OAAA;AAAE,oHAAA,YAAY,OAAA;AAIlD,YAAY;AACZ,uDASiC;AAR/B,iIAAA,kCAAkC,OAAA;AAClC,uHAAA,wBAAwB,OAAA;AACxB,8HAAA,+BAA+B,OAAA;AAC/B,qIAAA,sCAAsC,OAAA;AACtC,qHAAA,sBAAsB,OAAA;AACtB,4HAAA,6BAA6B,OAAA;AAC7B,gIAAA,iCAAiC,OAAA;AACjC,8HAAA,+BAA+B,OAAA;AAGjC,SAAS;AACT,4DAAiE;AAAxD,gHAAA,aAAa,OAAA;AAAE,yGAAA,MAAM,OAAA"}

package/dist/core/types/plate-jacketing.type.d.ts

@@ -33,3 +33,40 @@ export interface PlateInterfaceBoltInput extends PlateShearFlowInput {
     boltsPerRow: number;
     transferLength: number;
 }
+/**
+ * How the side plates are laid out along the span.
+ *
+ * `"continuous"` is an unbroken plate over the strengthened length; `"strips"`
+ * are discrete plates of width `width` repeating at pitch `spacing`, acting like
+ * external stirrups.
+ */
+export type SidePlateConfiguration = "continuous" | "strips";
+/**
+ * Bolt group anchoring the side plates to the web.
+ *
+ * `rowSpacing` is the horizontal pitch of the vertical bolt rows along the span;
+ * for a stripped layout it is normally the strip spacing itself. `boltsPerRow`
+ * counts the bolts in one vertical row, on one face of the beam.
+ */
+export interface SidePlateAnchorage {
+    bolt: BoltProps;
+    boltsPerRow: number;
+    rowSpacing: number;
+}
+export interface SidePlateShearProps {
+    fy: number;
+    Es?: number;
+    thickness: number;
+    depth: number;
+    configuration: SidePlateConfiguration;
+    width?: number;
+    spacing?: number;
+    angle?: number;
+    sides?: 1 | 2;
+    anchorage?: SidePlateAnchorage;
+}
+/**
+ * A side plate counts as present only when both its thickness and engaged depth
+ * are positive.
+ */
+export declare function hasSidePlate(props: SidePlateShearProps): boolean;

package/dist/core/types/plate-jacketing.type.js

@@ -2,6 +2,7 @@
 Object.defineProperty(exports, "__esModule", { value: true });
 exports.hasTopPlate = hasTopPlate;
 exports.hasBottomPlate = hasBottomPlate;
+exports.hasSidePlate = hasSidePlate;
 /**
  * A plate counts as present only when both its width and thickness are positive,
  * so a bottom-only jacket may omit the top plate fields or pass them as zero.
@@ -12,4 +13,11 @@ function hasTopPlate(props) {
 function hasBottomPlate(props) {
     return (props.bottomSteelWidth ?? 0) > 0 && (props.bottomSteelThickness ?? 0) > 0;
 }
+/**
+ * A side plate counts as present only when both its thickness and engaged depth
+ * are positive.
+ */
+function hasSidePlate(props) {
+    return props.thickness > 0 && props.depth > 0;
+}
 //# sourceMappingURL=plate-jacketing.type.js.map

package/dist/core/types/plate-jacketing.type.js.map

@@ -1 +1 @@
-{"version":3,"file":"plate-jacketing.type.js","sourceRoot":"","sources":["../../../src/core/types/plate-jacketing.type.ts"],"names":[],"mappings":";;AAeA,kCAEC;AAED,wCAEC;AAVD;;;GAGG;AACH,SAAgB,WAAW,CAAC,KAAyB;IACnD,OAAO,CAAC,KAAK,CAAC,aAAa,IAAI,CAAC,CAAC,GAAG,CAAC,IAAI,CAAC,KAAK,CAAC,iBAAiB,IAAI,CAAC,CAAC,GAAG,CAAC,CAAC;AAC9E,CAAC;AAED,SAAgB,cAAc,CAAC,KAAyB;IACtD,OAAO,CAAC,KAAK,CAAC,gBAAgB,IAAI,CAAC,CAAC,GAAG,CAAC,IAAI,CAAC,KAAK,CAAC,oBAAoB,IAAI,CAAC,CAAC,GAAG,CAAC,CAAC;AACpF,CAAC"}
+{"version":3,"file":"plate-jacketing.type.js","sourceRoot":"","sources":["../../../src/core/types/plate-jacketing.type.ts"],"names":[],"mappings":";;AAeA,kCAEC;AAED,wCAEC;AAiED,oCAEC;AA7ED;;;GAGG;AACH,SAAgB,WAAW,CAAC,KAAyB;IACnD,OAAO,CAAC,KAAK,CAAC,aAAa,IAAI,CAAC,CAAC,GAAG,CAAC,IAAI,CAAC,KAAK,CAAC,iBAAiB,IAAI,CAAC,CAAC,GAAG,CAAC,CAAC;AAC9E,CAAC;AAED,SAAgB,cAAc,CAAC,KAAyB;IACtD,OAAO,CAAC,KAAK,CAAC,gBAAgB,IAAI,CAAC,CAAC,GAAG,CAAC,IAAI,CAAC,KAAK,CAAC,oBAAoB,IAAI,CAAC,CAAC,GAAG,CAAC,CAAC;AACpF,CAAC;AA6DD;;;GAGG;AACH,SAAgB,YAAY,CAAC,KAA0B;IACrD,OAAO,KAAK,CAAC,SAAS,GAAG,CAAC,IAAI,KAAK,CAAC,KAAK,GAAG,CAAC,CAAC;AAChD,CAAC"}

package/dist/index.d.ts

@@ -1,5 +1,5 @@
 export { rectBeamMomentCapacity, rectBeamBarLayout, concreteShearCapacity, stirrupShearCapacity, checkStirrupRequirement, concreteBeta, concreteElasticModulus, psiToMpa, } from "./rc";
-export { calculateSteelJacketedBeamMomentCapacity, plateInterfaceShearFlow, boltShearCapacity, plateInterfaceBoltRequirement, } from "./strengthening";
-export type { RectBeamSection, RectSinglyBeamSection, RectDoublyBeamSection, RectShearSection, StirrupShearSection, ShearReinforcementCheckInput, RebarGroupInput, RectBeamBarLayoutInput, SteelJacketedProps, SectionState, PlateShearFlowInput, BoltProps, PlateInterfaceBoltInput, Warnings, calculationResult, unit, } from "./core";
-export { isSinglyReinforced, hasTopPlate, hasBottomPlate, FLEXURAL_STRENGTH_REDUCTION_FACTOR, CONCRETE_ULTIMATE_STRAIN, SHEAR_STRENGTH_REDUCTION_FACTOR, ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR, MAX_PLATE_BOLT_SPACING, RCDesignError, Errors, } from "./core";
+export { calculateSteelJacketedBeamMomentCapacity, plateInterfaceShearFlow, boltShearCapacity, plateInterfaceBoltRequirement, sidePlateShearCapacityByWebYielding, sidePlateShearCapacityByTensionTie, compareSidePlateShearCapacity, } from "./strengthening";
+export type { RectBeamSection, RectSinglyBeamSection, RectDoublyBeamSection, RectShearSection, StirrupShearSection, ShearReinforcementCheckInput, RebarGroupInput, RectBeamBarLayoutInput, SteelJacketedProps, SectionState, PlateShearFlowInput, BoltProps, PlateInterfaceBoltInput, SidePlateConfiguration, SidePlateAnchorage, SidePlateShearProps, Warnings, calculationResult, unit, } from "./core";
+export { isSinglyReinforced, hasTopPlate, hasBottomPlate, hasSidePlate, FLEXURAL_STRENGTH_REDUCTION_FACTOR, CONCRETE_ULTIMATE_STRAIN, SHEAR_STRENGTH_REDUCTION_FACTOR, ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR, MAX_PLATE_BOLT_SPACING, PLATE_SHEAR_YIELD_COEFFICIENT, SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT, SIDE_PLATE_REDUCTION_FACTOR_PSI, RCDesignError, Errors, } from "./core";
 export { solveQuadratic, roundToDecimalPlaces, mergeWarnings } from "./utils";

package/dist/index.js

@@ -1,6 +1,6 @@
 "use strict";
 Object.defineProperty(exports, "__esModule", { value: true });
-exports.mergeWarnings = exports.roundToDecimalPlaces = exports.solveQuadratic = exports.Errors = exports.RCDesignError = exports.MAX_PLATE_BOLT_SPACING = exports.ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR = exports.SHEAR_STRENGTH_REDUCTION_FACTOR = exports.CONCRETE_ULTIMATE_STRAIN = exports.FLEXURAL_STRENGTH_REDUCTION_FACTOR = exports.hasBottomPlate = exports.hasTopPlate = exports.isSinglyReinforced = exports.plateInterfaceBoltRequirement = exports.boltShearCapacity = exports.plateInterfaceShearFlow = exports.calculateSteelJacketedBeamMomentCapacity = exports.psiToMpa = exports.concreteElasticModulus = exports.concreteBeta = exports.checkStirrupRequirement = exports.stirrupShearCapacity = exports.concreteShearCapacity = exports.rectBeamBarLayout = exports.rectBeamMomentCapacity = void 0;
+exports.mergeWarnings = exports.roundToDecimalPlaces = exports.solveQuadratic = exports.Errors = exports.RCDesignError = exports.SIDE_PLATE_REDUCTION_FACTOR_PSI = exports.SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT = exports.PLATE_SHEAR_YIELD_COEFFICIENT = exports.MAX_PLATE_BOLT_SPACING = exports.ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR = exports.SHEAR_STRENGTH_REDUCTION_FACTOR = exports.CONCRETE_ULTIMATE_STRAIN = exports.FLEXURAL_STRENGTH_REDUCTION_FACTOR = exports.hasSidePlate = exports.hasBottomPlate = exports.hasTopPlate = exports.isSinglyReinforced = exports.compareSidePlateShearCapacity = exports.sidePlateShearCapacityByTensionTie = exports.sidePlateShearCapacityByWebYielding = exports.plateInterfaceBoltRequirement = exports.boltShearCapacity = exports.plateInterfaceShearFlow = exports.calculateSteelJacketedBeamMomentCapacity = exports.psiToMpa = exports.concreteElasticModulus = exports.concreteBeta = exports.checkStirrupRequirement = exports.stirrupShearCapacity = exports.concreteShearCapacity = exports.rectBeamBarLayout = exports.rectBeamMomentCapacity = void 0;
 // RC Beam Design
 var rc_1 = require("./rc");
 Object.defineProperty(exports, "rectBeamMomentCapacity", { enumerable: true, get: function () { return rc_1.rectBeamMomentCapacity; } });
@@ -17,15 +17,22 @@ Object.defineProperty(exports, "calculateSteelJacketedBeamMomentCapacity", { enu
 Object.defineProperty(exports, "plateInterfaceShearFlow", { enumerable: true, get: function () { return strengthening_1.plateInterfaceShearFlow; } });
 Object.defineProperty(exports, "boltShearCapacity", { enumerable: true, get: function () { return strengthening_1.boltShearCapacity; } });
 Object.defineProperty(exports, "plateInterfaceBoltRequirement", { enumerable: true, get: function () { return strengthening_1.plateInterfaceBoltRequirement; } });
+Object.defineProperty(exports, "sidePlateShearCapacityByWebYielding", { enumerable: true, get: function () { return strengthening_1.sidePlateShearCapacityByWebYielding; } });
+Object.defineProperty(exports, "sidePlateShearCapacityByTensionTie", { enumerable: true, get: function () { return strengthening_1.sidePlateShearCapacityByTensionTie; } });
+Object.defineProperty(exports, "compareSidePlateShearCapacity", { enumerable: true, get: function () { return strengthening_1.compareSidePlateShearCapacity; } });
 var core_1 = require("./core");
 Object.defineProperty(exports, "isSinglyReinforced", { enumerable: true, get: function () { return core_1.isSinglyReinforced; } });
 Object.defineProperty(exports, "hasTopPlate", { enumerable: true, get: function () { return core_1.hasTopPlate; } });
 Object.defineProperty(exports, "hasBottomPlate", { enumerable: true, get: function () { return core_1.hasBottomPlate; } });
+Object.defineProperty(exports, "hasSidePlate", { enumerable: true, get: function () { return core_1.hasSidePlate; } });
 Object.defineProperty(exports, "FLEXURAL_STRENGTH_REDUCTION_FACTOR", { enumerable: true, get: function () { return core_1.FLEXURAL_STRENGTH_REDUCTION_FACTOR; } });
 Object.defineProperty(exports, "CONCRETE_ULTIMATE_STRAIN", { enumerable: true, get: function () { return core_1.CONCRETE_ULTIMATE_STRAIN; } });
 Object.defineProperty(exports, "SHEAR_STRENGTH_REDUCTION_FACTOR", { enumerable: true, get: function () { return core_1.SHEAR_STRENGTH_REDUCTION_FACTOR; } });
 Object.defineProperty(exports, "ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR", { enumerable: true, get: function () { return core_1.ANCHOR_SHEAR_STRENGTH_REDUCTION_FACTOR; } });
 Object.defineProperty(exports, "MAX_PLATE_BOLT_SPACING", { enumerable: true, get: function () { return core_1.MAX_PLATE_BOLT_SPACING; } });
+Object.defineProperty(exports, "PLATE_SHEAR_YIELD_COEFFICIENT", { enumerable: true, get: function () { return core_1.PLATE_SHEAR_YIELD_COEFFICIENT; } });
+Object.defineProperty(exports, "SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT", { enumerable: true, get: function () { return core_1.SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT; } });
+Object.defineProperty(exports, "SIDE_PLATE_REDUCTION_FACTOR_PSI", { enumerable: true, get: function () { return core_1.SIDE_PLATE_REDUCTION_FACTOR_PSI; } });
 Object.defineProperty(exports, "RCDesignError", { enumerable: true, get: function () { return core_1.RCDesignError; } });
 Object.defineProperty(exports, "Errors", { enumerable: true, get: function () { return core_1.Errors; } });
 // Utilities

package/dist/index.js.map

@@ -1 +1 @@
-{"version":3,"file":"index.js","sourceRoot":"","sources":["../src/index.ts"],"names":[],"mappings":";;;AAAA,iBAAiB;AACjB,2BASc;AARZ,4GAAA,sBAAsB,OAAA;AACtB,uGAAA,iBAAiB,OAAA;AACjB,2GAAA,qBAAqB,OAAA;AACrB,0GAAA,oBAAoB,OAAA;AACpB,6GAAA,uBAAuB,OAAA;AACvB,kGAAA,YAAY,OAAA;AACZ,4GAAA,sBAAsB,OAAA;AACtB,8FAAA,QAAQ,OAAA;AAGV,gBAAgB;AAChB,iDAKyB;AAJvB,yIAAA,wCAAwC,OAAA;AACxC,wHAAA,uBAAuB,OAAA;AACvB,kHAAA,iBAAiB,OAAA;AACjB,8HAAA,6BAA6B,OAAA;AAuB/B,+BAWgB;AAVd,0GAAA,kBAAkB,OAAA;AAClB,mGAAA,WAAW,OAAA;AACX,sGAAA,cAAc,OAAA;AACd,0HAAA,kCAAkC,OAAA;AAClC,gHAAA,wBAAwB,OAAA;AACxB,uHAAA,+BAA+B,OAAA;AAC/B,8HAAA,sCAAsC,OAAA;AACtC,8GAAA,sBAAsB,OAAA;AACtB,qGAAA,aAAa,OAAA;AACb,8FAAA,MAAM,OAAA;AAGR,YAAY;AACZ,iCAA8E;AAArE,uGAAA,cAAc,OAAA;AAAE,6GAAA,oBAAoB,OAAA;AAAE,sGAAA,aAAa,OAAA"}
+{"version":3,"file":"index.js","sourceRoot":"","sources":["../src/index.ts"],"names":[],"mappings":";;;AAAA,iBAAiB;AACjB,2BASc;AARZ,4GAAA,sBAAsB,OAAA;AACtB,uGAAA,iBAAiB,OAAA;AACjB,2GAAA,qBAAqB,OAAA;AACrB,0GAAA,oBAAoB,OAAA;AACpB,6GAAA,uBAAuB,OAAA;AACvB,kGAAA,YAAY,OAAA;AACZ,4GAAA,sBAAsB,OAAA;AACtB,8FAAA,QAAQ,OAAA;AAGV,gBAAgB;AAChB,iDAQyB;AAPvB,yIAAA,wCAAwC,OAAA;AACxC,wHAAA,uBAAuB,OAAA;AACvB,kHAAA,iBAAiB,OAAA;AACjB,8HAAA,6BAA6B,OAAA;AAC7B,oIAAA,mCAAmC,OAAA;AACnC,mIAAA,kCAAkC,OAAA;AAClC,8HAAA,6BAA6B,OAAA;AA0B/B,+BAegB;AAdd,0GAAA,kBAAkB,OAAA;AAClB,mGAAA,WAAW,OAAA;AACX,sGAAA,cAAc,OAAA;AACd,oGAAA,YAAY,OAAA;AACZ,0HAAA,kCAAkC,OAAA;AAClC,gHAAA,wBAAwB,OAAA;AACxB,uHAAA,+BAA+B,OAAA;AAC/B,8HAAA,sCAAsC,OAAA;AACtC,8GAAA,sBAAsB,OAAA;AACtB,qHAAA,6BAA6B,OAAA;AAC7B,yHAAA,iCAAiC,OAAA;AACjC,uHAAA,+BAA+B,OAAA;AAC/B,qGAAA,aAAa,OAAA;AACb,8FAAA,MAAM,OAAA;AAGR,YAAY;AACZ,iCAA8E;AAArE,uGAAA,cAAc,OAAA;AAAE,6GAAA,oBAAoB,OAAA;AAAE,sGAAA,aAAa,OAAA"}

package/dist/strengthening/index.d.ts

@@ -1,2 +1,3 @@
 export { calculateSteelJacketedBeamMomentCapacity } from "./rc-beam-steel-plate-jacketing";
 export { plateInterfaceShearFlow, boltShearCapacity, plateInterfaceBoltRequirement, } from "./rc-beam-plate-interface-bolts";
+export { sidePlateShearCapacityByWebYielding, sidePlateShearCapacityByTensionTie, compareSidePlateShearCapacity, } from "./rc-beam-side-plate-shear";

package/dist/strengthening/index.js

@@ -1,10 +1,14 @@
 "use strict";
 Object.defineProperty(exports, "__esModule", { value: true });
-exports.plateInterfaceBoltRequirement = exports.boltShearCapacity = exports.plateInterfaceShearFlow = exports.calculateSteelJacketedBeamMomentCapacity = void 0;
+exports.compareSidePlateShearCapacity = exports.sidePlateShearCapacityByTensionTie = exports.sidePlateShearCapacityByWebYielding = exports.plateInterfaceBoltRequirement = exports.boltShearCapacity = exports.plateInterfaceShearFlow = exports.calculateSteelJacketedBeamMomentCapacity = void 0;
 var rc_beam_steel_plate_jacketing_1 = require("./rc-beam-steel-plate-jacketing");
 Object.defineProperty(exports, "calculateSteelJacketedBeamMomentCapacity", { enumerable: true, get: function () { return rc_beam_steel_plate_jacketing_1.calculateSteelJacketedBeamMomentCapacity; } });
 var rc_beam_plate_interface_bolts_1 = require("./rc-beam-plate-interface-bolts");
 Object.defineProperty(exports, "plateInterfaceShearFlow", { enumerable: true, get: function () { return rc_beam_plate_interface_bolts_1.plateInterfaceShearFlow; } });
 Object.defineProperty(exports, "boltShearCapacity", { enumerable: true, get: function () { return rc_beam_plate_interface_bolts_1.boltShearCapacity; } });
 Object.defineProperty(exports, "plateInterfaceBoltRequirement", { enumerable: true, get: function () { return rc_beam_plate_interface_bolts_1.plateInterfaceBoltRequirement; } });
+var rc_beam_side_plate_shear_1 = require("./rc-beam-side-plate-shear");
+Object.defineProperty(exports, "sidePlateShearCapacityByWebYielding", { enumerable: true, get: function () { return rc_beam_side_plate_shear_1.sidePlateShearCapacityByWebYielding; } });
+Object.defineProperty(exports, "sidePlateShearCapacityByTensionTie", { enumerable: true, get: function () { return rc_beam_side_plate_shear_1.sidePlateShearCapacityByTensionTie; } });
+Object.defineProperty(exports, "compareSidePlateShearCapacity", { enumerable: true, get: function () { return rc_beam_side_plate_shear_1.compareSidePlateShearCapacity; } });
 //# sourceMappingURL=index.js.map

package/dist/strengthening/index.js.map

@@ -1 +1 @@
-{"version":3,"file":"index.js","sourceRoot":"","sources":["../../src/strengthening/index.ts"],"names":[],"mappings":";;;AAAA,iFAA2F;AAAlF,yJAAA,wCAAwC,OAAA;AACjD,iFAIyC;AAHvC,wIAAA,uBAAuB,OAAA;AACvB,kIAAA,iBAAiB,OAAA;AACjB,8IAAA,6BAA6B,OAAA"}
+{"version":3,"file":"index.js","sourceRoot":"","sources":["../../src/strengthening/index.ts"],"names":[],"mappings":";;;AAAA,iFAA2F;AAAlF,yJAAA,wCAAwC,OAAA;AACjD,iFAIyC;AAHvC,wIAAA,uBAAuB,OAAA;AACvB,kIAAA,iBAAiB,OAAA;AACjB,8IAAA,6BAA6B,OAAA;AAE/B,uEAIoC;AAHlC,+IAAA,mCAAmC,OAAA;AACnC,8IAAA,kCAAkC,OAAA;AAClC,yIAAA,6BAA6B,OAAA"}

package/dist/strengthening/rc-beam-side-plate-shear.d.ts

@@ -0,0 +1,254 @@
+import { StirrupShearSection } from "../core/types/rc-beam.type";
+import { SidePlateShearProps } from "../core/types/plate-jacketing.type";
+/**
+ * Shear capacity of a beam strengthened with bolted steel side plates, treating
+ * each plate as a supplementary web that resists in-plane shear.
+ *
+ * The plate reaches the von Mises shear yield stress of 0.6 fy (AISC 360 G2.1):
+ *
+ * - continuous: `Vp = nSides · 0.6 fy · tp · dp`
+ * - strips: `Vp = nSides · 0.6 fy · tp · dp · wp / s`
+ *
+ * Strips are handled as the fraction `wp / s` of a continuous web, which is an
+ * approximation — a discrete strip works more as a tension tie than as a web
+ * panel, which is what `sidePlateShearCapacityByTensionTie` models. Run both and
+ * take the lower value, or call `compareSidePlateShearCapacity`.
+ *
+ * ACI 318-19 has no provisions for steel side plates in shear; a warning always
+ * says so.
+ *
+ * @param section - Original beam shear properties (fc_, bw, d, Av, fyt, s, optional lambda)
+ * @param plates - Side plate geometry, strength, layout, and optional anchorage
+ * @returns `before` and `after` results, each with `phiVn` (kN), `calculationDetails`,
+ *   `unit`, and `warnings`; `after` also carries `phiVp` and `governedBy`
+ * @throws {RCDesignError} 205 if the plate geometry is inconsistent, 206 if the
+ *   existing Vs leaves no headroom under the ACI 318-19 22.5.1.2 maximum, 202 if
+ *   the supplied bolt capacity is invalid
+ */
+export declare const sidePlateShearCapacityByWebYielding: (section: StirrupShearSection, plates: SidePlateShearProps) => {
+    method: "webYielding" | "tensionTie";
+    before: {
+        phiVn: number;
+        calculationDetails: {
+            phiVc: number;
+            phiVs: number;
+            Vc: number;
+            Vs: number;
+        };
+        unit: string;
+        warnings: {
+            reference?: string;
+            message: string;
+        }[];
+    };
+    after: {
+        phiVn: number;
+        phiVp: number;
+        governedBy: "plateCapacity" | "anchorage" | "webCrushing";
+        calculationDetails: {
+            phiVc: number;
+            phiVs: number;
+            Vp: number;
+            VpEffective: number;
+            maxVs: number;
+            headroom: number;
+            phiVpPlate: number;
+            phiVanchorage: number | null;
+            anchorageRows: number | null;
+            phiVbolt: number | null;
+            sides: number;
+            coverageRatio: number;
+        } & {
+            tauY: number;
+            slenderness: number;
+            slendernessLimit: number;
+        };
+        unit: string;
+        warnings: {
+            reference?: string;
+            message: string;
+        }[];
+    };
+};
+/**
+ * Shear capacity of a beam strengthened with bolted steel side plates, treating
+ * each plate as a tension tie crossing the diagonal crack, following the bonded
+ * shear reinforcement model of ACI 440.2R-17 §11.4 with steel in place of FRP:
+ *
+ * `Vp = nSides · tp · wp · ffe · (sin α + cos α) · dp / s`
+ *
+ * with `ffe = min(fy, Es · 0.004)` — the 0.004 strain cap of 440.2R §11.4, which
+ * keeps the crack tight enough for aggregate interlock — and the additional
+ * reduction factor `psi_f = 0.85` for two-sided bonded strengthening. A continuous
+ * plate is the case `wp = s`, `α = 90°`.
+ *
+ * Note that for structural steel `Es · 0.004 = 800 MPa` sits above any normal `fy`,
+ * so the strain cap does not bind and the tie reaches yield; this model therefore
+ * usually returns a higher capacity than `sidePlateShearCapacityByWebYielding` for
+ * a continuous plate. Neither is code-sanctioned for steel side plates — a warning
+ * always says so.
+ *
+ * @param section - Original beam shear properties (fc_, bw, d, Av, fyt, s, optional lambda)
+ * @param plates - Side plate geometry, strength, layout, and optional anchorage
+ * @returns `before` and `after` results, each with `phiVn` (kN), `calculationDetails`,
+ *   `unit`, and `warnings`; `after` also carries `phiVp` and `governedBy`
+ * @throws {RCDesignError} 205 if the plate geometry is inconsistent, 206 if the
+ *   existing Vs leaves no headroom under the ACI 318-19 22.5.1.2 maximum, 202 if
+ *   the supplied bolt capacity is invalid
+ */
+export declare const sidePlateShearCapacityByTensionTie: (section: StirrupShearSection, plates: SidePlateShearProps) => {
+    method: "webYielding" | "tensionTie";
+    before: {
+        phiVn: number;
+        calculationDetails: {
+            phiVc: number;
+            phiVs: number;
+            Vc: number;
+            Vs: number;
+        };
+        unit: string;
+        warnings: {
+            reference?: string;
+            message: string;
+        }[];
+    };
+    after: {
+        phiVn: number;
+        phiVp: number;
+        governedBy: "plateCapacity" | "anchorage" | "webCrushing";
+        calculationDetails: {
+            phiVc: number;
+            phiVs: number;
+            Vp: number;
+            VpEffective: number;
+            maxVs: number;
+            headroom: number;
+            phiVpPlate: number;
+            phiVanchorage: number | null;
+            anchorageRows: number | null;
+            phiVbolt: number | null;
+            sides: number;
+            coverageRatio: number;
+        } & {
+            ffe: number;
+            strainLimitedStress: number;
+            orientation: number;
+            psi: number;
+        };
+        unit: string;
+        warnings: {
+            reference?: string;
+            message: string;
+        }[];
+    };
+};
+/**
+ * Runs both side plate shear models on the same section and reports the lower
+ * result as governing, which is the intended entry point when selecting a
+ * conservative design capacity.
+ *
+ * @param section - Original beam shear properties (fc_, bw, d, Av, fyt, s, optional lambda)
+ * @param plates - Side plate geometry, strength, layout, and optional anchorage
+ * @returns `webYielding` and `tensionTie` results plus `governing`, holding the
+ *   lower `phiVn`, its `phiVp`, and the `method` that produced it
+ * @throws {RCDesignError} Whatever either model throws — see their documentation
+ */
+export declare const compareSidePlateShearCapacity: (section: StirrupShearSection, plates: SidePlateShearProps) => {
+    webYielding: {
+        method: "webYielding" | "tensionTie";
+        before: {
+            phiVn: number;
+            calculationDetails: {
+                phiVc: number;
+                phiVs: number;
+                Vc: number;
+                Vs: number;
+            };
+            unit: string;
+            warnings: {
+                reference?: string;
+                message: string;
+            }[];
+        };
+        after: {
+            phiVn: number;
+            phiVp: number;
+            governedBy: "plateCapacity" | "anchorage" | "webCrushing";
+            calculationDetails: {
+                phiVc: number;
+                phiVs: number;
+                Vp: number;
+                VpEffective: number;
+                maxVs: number;
+                headroom: number;
+                phiVpPlate: number;
+                phiVanchorage: number | null;
+                anchorageRows: number | null;
+                phiVbolt: number | null;
+                sides: number;
+                coverageRatio: number;
+            } & {
+                tauY: number;
+                slenderness: number;
+                slendernessLimit: number;
+            };
+            unit: string;
+            warnings: {
+                reference?: string;
+                message: string;
+            }[];
+        };
+    };
+    tensionTie: {
+        method: "webYielding" | "tensionTie";
+        before: {
+            phiVn: number;
+            calculationDetails: {
+                phiVc: number;
+                phiVs: number;
+                Vc: number;
+                Vs: number;
+            };
+            unit: string;
+            warnings: {
+                reference?: string;
+                message: string;
+            }[];
+        };
+        after: {
+            phiVn: number;
+            phiVp: number;
+            governedBy: "plateCapacity" | "anchorage" | "webCrushing";
+            calculationDetails: {
+                phiVc: number;
+                phiVs: number;
+                Vp: number;
+                VpEffective: number;
+                maxVs: number;
+                headroom: number;
+                phiVpPlate: number;
+                phiVanchorage: number | null;
+                anchorageRows: number | null;
+                phiVbolt: number | null;
+                sides: number;
+                coverageRatio: number;
+            } & {
+                ffe: number;
+                strainLimitedStress: number;
+                orientation: number;
+                psi: number;
+            };
+            unit: string;
+            warnings: {
+                reference?: string;
+                message: string;
+            }[];
+        };
+    };
+    governing: {
+        method: "webYielding" | "tensionTie";
+        phiVn: number;
+        phiVp: number;
+        governedBy: "plateCapacity" | "anchorage" | "webCrushing";
+    };
+};

package/dist/strengthening/rc-beam-side-plate-shear.js

@@ -0,0 +1,420 @@
+"use strict";
+var __createBinding = (this && this.__createBinding) || (Object.create ? (function(o, m, k, k2) {
+    if (k2 === undefined) k2 = k;
+    var desc = Object.getOwnPropertyDescriptor(m, k);
+    if (!desc || ("get" in desc ? !m.__esModule : desc.writable || desc.configurable)) {
+      desc = { enumerable: true, get: function() { return m[k]; } };
+    }
+    Object.defineProperty(o, k2, desc);
+}) : (function(o, m, k, k2) {
+    if (k2 === undefined) k2 = k;
+    o[k2] = m[k];
+}));
+var __setModuleDefault = (this && this.__setModuleDefault) || (Object.create ? (function(o, v) {
+    Object.defineProperty(o, "default", { enumerable: true, value: v });
+}) : function(o, v) {
+    o["default"] = v;
+});
+var __importStar = (this && this.__importStar) || (function () {
+    var ownKeys = function(o) {
+        ownKeys = Object.getOwnPropertyNames || function (o) {
+            var ar = [];
+            for (var k in o) if (Object.prototype.hasOwnProperty.call(o, k)) ar[ar.length] = k;
+            return ar;
+        };
+        return ownKeys(o);
+    };
+    return function (mod) {
+        if (mod && mod.__esModule) return mod;
+        var result = {};
+        if (mod != null) for (var k = ownKeys(mod), i = 0; i < k.length; i++) if (k[i] !== "default") __createBinding(result, mod, k[i]);
+        __setModuleDefault(result, mod);
+        return result;
+    };
+})();
+Object.defineProperty(exports, "__esModule", { value: true });
+exports.compareSidePlateShearCapacity = exports.sidePlateShearCapacityByTensionTie = exports.sidePlateShearCapacityByWebYielding = void 0;
+const rc_design_error_1 = require("../core/errors/rc-design.error");
+const MyMath = __importStar(require("../utils/math"));
+const RCConstants = __importStar(require("../core/constants/rc.constant"));
+const rc_beam_design_1 = require("../rc/rc-beam-design");
+const rc_beam_plate_interface_bolts_1 = require("./rc-beam-plate-interface-bolts");
+const plate_jacketing_type_1 = require("../core/types/plate-jacketing.type");
+const resolveSidePlateGeometry = (plates) => {
+    const sides = plates.sides ?? RCConstants.DEFAULT_SIDE_PLATE_SIDES;
+    const Es = plates.Es ?? RCConstants.DEFAULT_PLATE_ELASTIC_MODULUS;
+    const strips = plates.configuration === "strips";
+    // A continuous plate is the limiting case of strips with wp = s, so it carries
+    // a coverage ratio of 1 and the vertical orientation the model assumes.
+    const wp = strips ? (plates.width ?? 0) : null;
+    const s = strips ? (plates.spacing ?? 0) : null;
+    const angle = strips
+        ? (plates.angle ?? RCConstants.DEFAULT_SIDE_PLATE_ANGLE)
+        : RCConstants.DEFAULT_SIDE_PLATE_ANGLE;
+    return {
+        sides,
+        tp: plates.thickness,
+        dp: plates.depth,
+        wp,
+        s,
+        coverageRatio: strips && s !== null && s > 0 ? wp / s : 1,
+        angleRad: (angle * Math.PI) / 180,
+        Es,
+        fy: plates.fy,
+        configuration: plates.configuration,
+    };
+};
+const validateSidePlateGeometry = (section, plates, geo) => {
+    if (!(0, plate_jacketing_type_1.hasSidePlate)(plates) ||
+        geo.fy <= 0 ||
+        geo.Es <= 0 ||
+        (geo.sides !== 1 && geo.sides !== 2) ||
+        section.bw <= 0 ||
+        section.d <= 0 ||
+        geo.dp > section.d) {
+        throw new rc_design_error_1.RCDesignError(rc_design_error_1.Errors.SIDE_PLATE_GEOMETRY_INVALID);
+    }
+    if (geo.configuration === "strips") {
+        const wp = geo.wp ?? 0;
+        const s = geo.s ?? 0;
+        // A strip wider than its pitch is a continuous plate described wrongly, and
+        // an inclination outside (0, 90] has no meaning in the tie model.
+        if (wp <= 0 || s <= 0 || wp > s || geo.angleRad <= 0 || geo.angleRad > Math.PI / 2) {
+            throw new rc_design_error_1.RCDesignError(rc_design_error_1.Errors.SIDE_PLATE_GEOMETRY_INVALID);
+        }
+    }
+    if (plates.anchorage !== undefined) {
+        const { boltsPerRow, rowSpacing } = plates.anchorage;
+        if (boltsPerRow <= 0 || rowSpacing <= 0) {
+            throw new rc_design_error_1.RCDesignError(rc_design_error_1.Errors.SIDE_PLATE_GEOMETRY_INVALID);
+        }
+    }
+};
+/**
+ * Shear capacity of the section before strengthening: φVc + φVs.
+ *
+ * A section with no stirrups (`Av <= 0` or `s <= 0`) contributes φVs = 0 rather
+ * than dividing by a zero spacing.
+ *
+ * An existing Vs beyond the ACI 318-19 22.5.1.2 maximum reaches `stirrupShearCapacity`
+ * as error 105 ("section too small for shear"). In the strengthening context the
+ * useful diagnosis is the more specific one — the web is already at its ceiling, so
+ * no added plate force can be developed — so it is re-thrown as 206.
+ */
+const baselineShearCapacity = (section) => {
+    const concrete = (0, rc_beam_design_1.concreteShearCapacity)(section);
+    const hasStirrups = section.Av > 0 && section.s > 0;
+    let stirrups;
+    if (hasStirrups) {
+        try {
+            stirrups = (0, rc_beam_design_1.stirrupShearCapacity)(section);
+        }
+        catch (error) {
+            if (error instanceof rc_design_error_1.RCDesignError && error.code === rc_design_error_1.Errors.SHEAR_STRENGTH_EXCEEDS_MAX.code) {
+                throw new rc_design_error_1.RCDesignError(rc_design_error_1.Errors.STRENGTHENED_SHEAR_NO_HEADROOM);
+            }
+            throw error;
+        }
+    }
+    else {
+        stirrups = { phiVs: 0, calculationDetails: { Vs: 0 }, warnings: [] };
+    }
+    return {
+        phiVn: MyMath.roundToDecimalPlaces(concrete.phiVc + stirrups.phiVs, 2),
+        phiVc: concrete.phiVc,
+        phiVs: stirrups.phiVs,
+        Vc: concrete.calculationDetails.Vc,
+        Vs: stirrups.calculationDetails.Vs,
+        warnings: [...concrete.warnings, ...stirrups.warnings],
+    };
+};
+/**
+ * Design strength the bolt group can drag into the concrete across a 45° crack.
+ *
+ * The crack's horizontal projection is taken as `dp`, so the rows anchoring the
+ * plate beyond it number `floor(dp / rowSpacing)`, at least one — the same
+ * `dfv / sf` counting ACI 440.2R uses for bonded shear reinforcement.
+ *
+ * The returned value already carries the anchor φ of 0.65 from `boltShearCapacity`,
+ * so it is compared against the plate's φVp on a design-strength basis.
+ */
+const anchorageCapacity = (anchorage, geo, warnings) => {
+    const boltResult = (0, rc_beam_plate_interface_bolts_1.boltShearCapacity)(anchorage.bolt);
+    warnings.push(...boltResult.warnings);
+    const exactRows = geo.dp / anchorage.rowSpacing;
+    const rows = Math.max(1, Math.floor(exactRows));
+    if (exactRows < 1) {
+        warnings.push({
+            message: `Bolt row spacing (${anchorage.rowSpacing} mm) exceeds the engaged plate depth (${geo.dp} mm); only one row was taken as crossing the assumed 45 degree crack.`,
+        });
+    }
+    // Same minimum anchor spacing `plateInterfaceBoltRequirement` checks, so the two
+    // strengthening paths hold bolt layouts to one rule.
+    if (anchorage.bolt.diameter !== undefined) {
+        const minSpacing = RCConstants.MIN_ANCHOR_SPACING_DIAMETER_FACTOR * anchorage.bolt.diameter;
+        if (anchorage.rowSpacing < minSpacing) {
+            warnings.push({
+                reference: "ACI318-19, 17.9.2",
+                message: `Bolt row spacing (${anchorage.rowSpacing} mm) is below the minimum anchor spacing of 4*da (${minSpacing} mm); use a larger pitch, a smaller bolt, or fewer rows.`,
+            });
+        }
+    }
+    return {
+        phiVanchorage: MyMath.roundToDecimalPlaces(geo.sides * rows * anchorage.boltsPerRow * boltResult.phiVbolt, 2),
+        rows,
+        phiVbolt: boltResult.phiVbolt,
+        boltsPerRow: anchorage.boltsPerRow,
+    };
+};
+/** Detailing and modelling warnings shared by both capacity models. */
+const collectCommonWarnings = (section, plates, geo, warnings) => {
+    warnings.push({
+        message: "ACI 318-19 contains no provisions for steel side plates in shear; this capacity is an engineering model, not a code-sanctioned calculation, and must be confirmed against test data or a specialist review.",
+    });
+    if (geo.dp < section.d) {
+        warnings.push({
+            message: `Engaged plate depth dp (${geo.dp} mm) is less than the effective depth d (${section.d} mm); only the plated depth was taken as resisting shear.`,
+        });
+    }
+    // Strip pitch is checked against ACI 318-19 9.7.6.2.2 alone, in `assembleResult`
+    // where Vp is known. ACI 440.2R-17 11.4.2 defers to the ACI 318 limits for internal
+    // steel shear reinforcement rather than imposing its own, so that one check
+    // satisfies both documents. (The `wf + d/4` rule of ACI 440.2R-08 did not survive
+    // into the 2017 edition and is deliberately not applied.)
+    if (geo.sides === 1) {
+        warnings.push({
+            message: "A plate on one face only loads the section eccentrically; the resulting torsion and out-of-plane twist are not captured by this in-plane shear model and must be assessed separately.",
+        });
+    }
+    if (plates.anchorage === undefined) {
+        warnings.push({
+            message: "No anchorage was supplied, so the reported capacity assumes the plate is fully developed; the bolt group or bond must be checked separately.",
+        });
+    }
+};
+/**
+ * Applies the ACI 318-19 22.5.1.2 web crushing cap and the anchorage limit, then
+ * assembles the `before`/`after` result both models return.
+ *
+ * The cap `Vs + Vp <= 0.66 sqrt(fc') bw d` — mirrored for bonded shear
+ * strengthening by ACI 440.2R-17 11.4.3, Eq. (11.4.3) — is a property of the concrete web, so
+ * it limits the plate force the web can host rather than invalidating the design:
+ * the plate contribution is truncated to the remaining headroom and a warning
+ * says so. Only a section whose existing Vs already exhausts the cap throws,
+ * because there no strengthening at all can be developed.
+ *
+ * @param VpNominal - Plate nominal shear contribution in N, before φ and before
+ *   any model-specific reduction factor
+ * @param reductionFactor - Model-specific factor applied to the plate term only
+ *   (1.0 for web yielding, psi_f for the tension tie)
+ */
+const assembleResult = (section, plates, geo, VpNominal, reductionFactor, method, modelDetails, warnings) => {
+    const before = baselineShearCapacity(section);
+    const baseWarnings = [...before.warnings, ...warnings];
+    const VpModelKN = VpNominal * reductionFactor * 0.001;
+    const maxVsKN = RCConstants.MAX_VS_COEFFICIENT * Math.sqrt(section.fc_) * section.bw * section.d * 0.001;
+    const headroomKN = maxVsKN - before.Vs;
+    if (headroomKN <= 0) {
+        throw new rc_design_error_1.RCDesignError(rc_design_error_1.Errors.STRENGTHENED_SHEAR_NO_HEADROOM);
+    }
+    const VpEffectiveKN = Math.min(VpModelKN, headroomKN);
+    const webCrushingGoverns = VpEffectiveKN < VpModelKN;
+    if (webCrushingGoverns) {
+        baseWarnings.push({
+            reference: "ACI318-19, 22.5.1.2",
+            message: `Plate contribution of ${MyMath.roundToDecimalPlaces(VpModelKN, 2)} kN truncated to the remaining web capacity of ${MyMath.roundToDecimalPlaces(headroomKN, 2)} kN, so that Vs + Vp stays within 0.66*sqrt(fc')*bw*d (${MyMath.roundToDecimalPlaces(maxVsKN, 2)} kN); a thinner or shallower plate carries the section just as far.`,
+        });
+    }
+    // ACI 318-19 9.7.6.2.2 halves the permitted spacing once the shear reinforcement
+    // carries more than 0.33*sqrt(fc')*bw*d. The plate is what usually pushes a section
+    // over that threshold, so the limit is keyed off Vs + Vp rather than Vs alone.
+    if (geo.configuration === "strips" && geo.s !== null) {
+        const sqrtFc = Math.sqrt(section.fc_);
+        const vsThresholdKN = RCConstants.VS_SPACING_THRESHOLD_COEFFICIENT * sqrtFc * section.bw * section.d * 0.001;
+        const highShear = before.Vs + VpEffectiveKN > vsThresholdKN;
+        const maxSpacing = highShear
+            ? Math.min(RCConstants.MAX_STIRRUP_SPACING_HIGH_VS_DEPTH_FACTOR * section.d, RCConstants.MAX_STIRRUP_SPACING_HIGH_VS)
+            : Math.min(RCConstants.MAX_STIRRUP_SPACING_LOW_VS_DEPTH_FACTOR * section.d, RCConstants.MAX_STIRRUP_SPACING_LOW_VS);
+        if (geo.s > maxSpacing) {
+            baseWarnings.push({
+                reference: "ACI318-19, 9.7.6.2.2",
+                message: `Strip pitch (${geo.s} mm) exceeds the maximum shear reinforcement spacing of ${MyMath.roundToDecimalPlaces(maxSpacing, 2)} mm${highShear ? `, tightened because Vs + Vp (${MyMath.roundToDecimalPlaces(before.Vs + VpEffectiveKN, 2)} kN) exceeds 0.33*sqrt(fc')*bw*d (${MyMath.roundToDecimalPlaces(vsThresholdKN, 2)} kN)` : ""}; a diagonal crack can pass between strips without crossing one.`,
+            });
+        }
+    }
+    const phiVpPlate = MyMath.roundToDecimalPlaces(RCConstants.SHEAR_STRENGTH_REDUCTION_FACTOR * VpEffectiveKN, 2);
+    const anchorage = plates.anchorage !== undefined ? anchorageCapacity(plates.anchorage, geo, baseWarnings) : null;
+    const anchorageGoverns = anchorage !== null && anchorage.phiVanchorage < phiVpPlate;
+    const phiVp = anchorageGoverns
+        ? anchorage.phiVanchorage
+        : phiVpPlate;
+    let governedBy = "plateCapacity";
+    if (anchorageGoverns) {
+        governedBy = "anchorage";
+    }
+    else if (webCrushingGoverns) {
+        governedBy = "webCrushing";
+    }
+    return {
+        method,
+        before: {
+            phiVn: before.phiVn,
+            calculationDetails: {
+                phiVc: before.phiVc,
+                phiVs: before.phiVs,
+                Vc: before.Vc,
+                Vs: before.Vs,
+            },
+            unit: "kN",
+            warnings: before.warnings,
+        },
+        after: {
+            phiVn: MyMath.roundToDecimalPlaces(before.phiVn + phiVp, 2),
+            phiVp: MyMath.roundToDecimalPlaces(phiVp, 2),
+            governedBy,
+            calculationDetails: {
+                phiVc: before.phiVc,
+                phiVs: before.phiVs,
+                Vp: MyMath.roundToDecimalPlaces(VpModelKN, 2),
+                VpEffective: MyMath.roundToDecimalPlaces(VpEffectiveKN, 2),
+                maxVs: MyMath.roundToDecimalPlaces(maxVsKN, 2),
+                headroom: MyMath.roundToDecimalPlaces(headroomKN, 2),
+                phiVpPlate,
+                phiVanchorage: anchorage !== null ? anchorage.phiVanchorage : null,
+                anchorageRows: anchorage !== null ? anchorage.rows : null,
+                phiVbolt: anchorage !== null ? anchorage.phiVbolt : null,
+                sides: geo.sides,
+                coverageRatio: MyMath.roundToDecimalPlaces(geo.coverageRatio, 4),
+                ...modelDetails,
+            },
+            unit: "kN",
+            warnings: baseWarnings,
+        },
+    };
+};
+/**
+ * Shear capacity of a beam strengthened with bolted steel side plates, treating
+ * each plate as a supplementary web that resists in-plane shear.
+ *
+ * The plate reaches the von Mises shear yield stress of 0.6 fy (AISC 360 G2.1):
+ *
+ * - continuous: `Vp = nSides · 0.6 fy · tp · dp`
+ * - strips: `Vp = nSides · 0.6 fy · tp · dp · wp / s`
+ *
+ * Strips are handled as the fraction `wp / s` of a continuous web, which is an
+ * approximation — a discrete strip works more as a tension tie than as a web
+ * panel, which is what `sidePlateShearCapacityByTensionTie` models. Run both and
+ * take the lower value, or call `compareSidePlateShearCapacity`.
+ *
+ * ACI 318-19 has no provisions for steel side plates in shear; a warning always
+ * says so.
+ *
+ * @param section - Original beam shear properties (fc_, bw, d, Av, fyt, s, optional lambda)
+ * @param plates - Side plate geometry, strength, layout, and optional anchorage
+ * @returns `before` and `after` results, each with `phiVn` (kN), `calculationDetails`,
+ *   `unit`, and `warnings`; `after` also carries `phiVp` and `governedBy`
+ * @throws {RCDesignError} 205 if the plate geometry is inconsistent, 206 if the
+ *   existing Vs leaves no headroom under the ACI 318-19 22.5.1.2 maximum, 202 if
+ *   the supplied bolt capacity is invalid
+ */
+const sidePlateShearCapacityByWebYielding = (section, plates) => {
+    const warnings = [];
+    const geo = resolveSidePlateGeometry(plates);
+    validateSidePlateGeometry(section, plates, geo);
+    collectCommonWarnings(section, plates, geo, warnings);
+    const tauY = RCConstants.PLATE_SHEAR_YIELD_COEFFICIENT * geo.fy; // MPa
+    const VpNominal = geo.sides * tauY * geo.tp * geo.dp * geo.coverageRatio; // N
+    // AISC 360 G2.1(a): beyond this slenderness the panel buckles in shear before it
+    // yields. The concrete restrains the inner face, so this is a warning, not a limit.
+    const slenderness = geo.dp / geo.tp;
+    const slendernessLimit = RCConstants.PLATE_SHEAR_SLENDERNESS_COEFFICIENT * Math.sqrt(geo.Es / geo.fy);
+    if (slenderness > slendernessLimit) {
+        warnings.push({
+            reference: "AISC360-22, G2.1",
+            message: `Plate slenderness dp/tp (${MyMath.roundToDecimalPlaces(slenderness, 1)}) exceeds 2.24*sqrt(Es/fy) (${MyMath.roundToDecimalPlaces(slendernessLimit, 1)}); shear buckling may precede yielding unless the plate is stiffened or continuously restrained by the concrete.`,
+        });
+    }
+    return assembleResult(section, plates, geo, VpNominal, 1.0, "webYielding", {
+        tauY: MyMath.roundToDecimalPlaces(tauY, 2),
+        slenderness: MyMath.roundToDecimalPlaces(slenderness, 1),
+        slendernessLimit: MyMath.roundToDecimalPlaces(slendernessLimit, 1),
+    }, warnings);
+};
+exports.sidePlateShearCapacityByWebYielding = sidePlateShearCapacityByWebYielding;
+/**
+ * Shear capacity of a beam strengthened with bolted steel side plates, treating
+ * each plate as a tension tie crossing the diagonal crack, following the bonded
+ * shear reinforcement model of ACI 440.2R-17 §11.4 with steel in place of FRP:
+ *
+ * `Vp = nSides · tp · wp · ffe · (sin α + cos α) · dp / s`
+ *
+ * with `ffe = min(fy, Es · 0.004)` — the 0.004 strain cap of 440.2R §11.4, which
+ * keeps the crack tight enough for aggregate interlock — and the additional
+ * reduction factor `psi_f = 0.85` for two-sided bonded strengthening. A continuous
+ * plate is the case `wp = s`, `α = 90°`.
+ *
+ * Note that for structural steel `Es · 0.004 = 800 MPa` sits above any normal `fy`,
+ * so the strain cap does not bind and the tie reaches yield; this model therefore
+ * usually returns a higher capacity than `sidePlateShearCapacityByWebYielding` for
+ * a continuous plate. Neither is code-sanctioned for steel side plates — a warning
+ * always says so.
+ *
+ * @param section - Original beam shear properties (fc_, bw, d, Av, fyt, s, optional lambda)
+ * @param plates - Side plate geometry, strength, layout, and optional anchorage
+ * @returns `before` and `after` results, each with `phiVn` (kN), `calculationDetails`,
+ *   `unit`, and `warnings`; `after` also carries `phiVp` and `governedBy`
+ * @throws {RCDesignError} 205 if the plate geometry is inconsistent, 206 if the
+ *   existing Vs leaves no headroom under the ACI 318-19 22.5.1.2 maximum, 202 if
+ *   the supplied bolt capacity is invalid
+ */
+const sidePlateShearCapacityByTensionTie = (section, plates) => {
+    const warnings = [];
+    const geo = resolveSidePlateGeometry(plates);
+    validateSidePlateGeometry(section, plates, geo);
+    collectCommonWarnings(section, plates, geo, warnings);
+    const strainLimitedStress = geo.Es * RCConstants.SIDE_PLATE_EFFECTIVE_STRAIN_LIMIT; // MPa
+    const ffe = Math.min(geo.fy, strainLimitedStress);
+    if (ffe < geo.fy) {
+        warnings.push({
+            reference: "ACI440.2R-17, 11.4",
+            message: `Effective plate stress limited to ${MyMath.roundToDecimalPlaces(ffe, 2)} MPa by the 0.004 strain cap, below fy (${geo.fy} MPa); the plate does not reach yield.`,
+        });
+    }
+    const orientation = Math.sin(geo.angleRad) + Math.cos(geo.angleRad);
+    const VpNominal = geo.sides * geo.tp * ffe * geo.dp * geo.coverageRatio * orientation; // N
+    return assembleResult(section, plates, geo, VpNominal, RCConstants.SIDE_PLATE_REDUCTION_FACTOR_PSI, "tensionTie", {
+        ffe: MyMath.roundToDecimalPlaces(ffe, 2),
+        strainLimitedStress: MyMath.roundToDecimalPlaces(strainLimitedStress, 2),
+        orientation: MyMath.roundToDecimalPlaces(orientation, 4),
+        psi: RCConstants.SIDE_PLATE_REDUCTION_FACTOR_PSI,
+    }, warnings);
+};
+exports.sidePlateShearCapacityByTensionTie = sidePlateShearCapacityByTensionTie;
+/**
+ * Runs both side plate shear models on the same section and reports the lower
+ * result as governing, which is the intended entry point when selecting a
+ * conservative design capacity.
+ *
+ * @param section - Original beam shear properties (fc_, bw, d, Av, fyt, s, optional lambda)
+ * @param plates - Side plate geometry, strength, layout, and optional anchorage
+ * @returns `webYielding` and `tensionTie` results plus `governing`, holding the
+ *   lower `phiVn`, its `phiVp`, and the `method` that produced it
+ * @throws {RCDesignError} Whatever either model throws — see their documentation
+ */
+const compareSidePlateShearCapacity = (section, plates) => {
+    const webYielding = (0, exports.sidePlateShearCapacityByWebYielding)(section, plates);
+    const tensionTie = (0, exports.sidePlateShearCapacityByTensionTie)(section, plates);
+    const governing = tensionTie.after.phiVn < webYielding.after.phiVn ? tensionTie : webYielding;
+    return {
+        webYielding,
+        tensionTie,
+        governing: {
+            method: governing.method,
+            phiVn: governing.after.phiVn,
+            phiVp: governing.after.phiVp,
+            governedBy: governing.after.governedBy,
+        },
+    };
+};
+exports.compareSidePlateShearCapacity = compareSidePlateShearCapacity;
+//# sourceMappingURL=rc-beam-side-plate-shear.js.map

package/dist/strengthening/rc-beam-side-plate-shear.js.map

@@ -0,0 +1 @@
+{"version":3,"file":"rc-beam-side-plate-shear.js","sourceRoot":"","sources":["../../src/strengthening/rc-beam-side-plate-shear.ts"],"names":[],"mappings":";;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;AAAA,sEAAyE;AACzE,wDAA0C;AAC1C,6EAA+D;AAE/D,2DAAqF;AAErF,mFAAoE;AAIpE,+EAK8C;AAuC9C,MAAM,wBAAwB,GAAG,CAAC,MAA2B,EAAqB,EAAE;IAClF,MAAM,KAAK,GAAG,MAAM,CAAC,KAAK,IAAI,WAAW,CAAC,wBAAwB,CAAC;IACnE,MAAM,EAAE,GAAG,MAAM,CAAC,EAAE,IAAI,WAAW,CAAC,6BAA6B,CAAC;IAClE,MAAM,MAAM,GAAG,MAAM,CAAC,aAAa,KAAK,QAAQ,CAAC;IAEjD,+EAA+E;IAC/E,wEAAwE;IACxE,MAAM,EAAE,GAAG,MAAM,CAAC,CAAC,CAAC,CAAC,MAAM,CAAC,KAAK,IAAI,CAAC,CAAC,CAAC,CAAC,CAAC,IAAI,CAAC;IAC/C,MAAM,CAAC,GAAG,MAAM,CAAC,CAAC,CAAC,CAAC,MAAM,CAAC,OAAO,IAAI,CAAC,CAAC,CAAC,CAAC,CAAC,IAAI,CAAC;IAChD,MAAM,KAAK,GAAG,MAAM;QAClB,CAAC,CAAC,CAAC,MAAM,CAAC,KAAK,IAAI,WAAW,CAAC,wBAAwB,CAAC;QACxD,CAAC,CAAC,WAAW,CAAC,wBAAwB,CAAC;IAEzC,OAAO;QACL,KAAK;QACL,EAAE,EAAE,MAAM,CAAC,SAAS;QACpB,EAAE,EAAE,MAAM,CAAC,KAAK;QAChB,EAAE;QACF,CAAC;QACD,aAAa,EAAE,MAAM,IAAI,CAAC,KAAK,IAAI,IAAI,CAAC,GAAG,CAAC,CAAC,CAAC,CAAE,EAAa,GAAG,CAAC,CAAC,CAAC,CAAC,CAAC;QACrE,QAAQ,EAAE,CAAC,KAAK,GAAG,IAAI,CAAC,EAAE,CAAC,GAAG,GAAG;QACjC,EAAE;QACF,EAAE,EAAE,MAAM,CAAC,EAAE;QACb,aAAa,EAAE,MAAM,CAAC,aAAa;KACpC,CAAC;AACJ,CAAC,CAAC;AAEF,MAAM,yBAAyB,GAAG,CAChC,OAA4B,EAC5B,MAA2B,EAC3B,GAAsB,EAChB,EAAE;IACR,IACE,CAAC,IAAA,mCAAY,EAAC,MAAM,CAAC;QACrB,GAAG,CAAC,EAAE,IAAI,CAAC;QACX,GAAG,CAAC,EAAE,IAAI,CAAC;QACX,CAAC,GAAG,CAAC,KAAK,KAAK,CAAC,IAAI,GAAG,CAAC,KAAK,KAAK,CAAC,CAAC;QACpC,OAAO,CAAC,EAAE,IAAI,CAAC;QACf,OAAO,CAAC,CAAC,IAAI,CAAC;QACd,GAAG,CAAC,EAAE,GAAG,OAAO,CAAC,CAAC,EAClB,CAAC;QACD,MAAM,IAAI,+BAAa,CAAC,wBAAM,CAAC,2BAA2B,CAAC,CAAC;IAC9D,CAAC;IAED,IAAI,GAAG,CAAC,aAAa,KAAK,QAAQ,EAAE,CAAC;QACnC,MAAM,EAAE,GAAG,GAAG,CAAC,EAAE,IAAI,CAAC,CAAC;QACvB,MAAM,CAAC,GAAG,GAAG,CAAC,CAAC,IAAI,CAAC,CAAC;QACrB,4EAA4E;QAC5E,kEAAkE;QAClE,IAAI,EAAE,IAAI,CAAC,IAAI,CAAC,IAAI,CAAC,IAAI,EAAE,GAAG,CAAC,IAAI,GAAG,CAAC,QAAQ,IAAI,CAAC,IAAI,GAAG,CAAC,QAAQ,GAAG,IAAI,CAAC,EAAE,GAAG,CAAC,EAAE,CAAC;YACnF,MAAM,IAAI,+BAAa,CAAC,wBAAM,CAAC,2BAA2B,CAAC,CAAC;QAC9D,CAAC;IACH,CAAC;IAED,IAAI,MAAM,CAAC,SAAS,KAAK,SAAS,EAAE,CAAC;QACnC,MAAM,EAAE,WAAW,EAAE,UAAU,EAAE,GAAG,MAAM,CAAC,SAAS,CAAC;QACrD,IAAI,WAAW,IAAI,CAAC,IAAI,UAAU,IAAI,CAAC,EAAE,CAAC;YACxC,MAAM,IAAI,+BAAa,CAAC,wBAAM,CAAC,2BAA2B,CAAC,CAAC;QAC9D,CAAC;IACH,CAAC;AACH,CAAC,CAAC;AAEF;;;;;;;;;;GAUG;AACH,MAAM,qBAAqB,GAAG,CAAC,OAA4B,EAAE,EAAE;IAC7D,MAAM,QAAQ,GAAG,IAAA,sCAAqB,EAAC,OAAO,CAAC,CAAC;IAEhD,MAAM,WAAW,GAAG,OAAO,CAAC,EAAE,GAAG,CAAC,IAAI,OAAO,CAAC,CAAC,GAAG,CAAC,CAAC;IACpD,IAAI,QAAmF,CAAC;IAExF,IAAI,WAAW,EAAE,CAAC;QAChB,IAAI,CAAC;YACH,QAAQ,GAAG,IAAA,qCAAoB,EAAC,OAAO,CAAC,CAAC;QAC3C,CAAC;QAAC,OAAO,KAAK,EAAE,CAAC;YACf,IAAI,KAAK,YAAY,+BAAa,IAAI,KAAK,CAAC,IAAI,KAAK,wBAAM,CAAC,0BAA0B,CAAC,IAAI,EAAE,CAAC;gBAC5F,MAAM,IAAI,+BAAa,CAAC,wBAAM,CAAC,8BAA8B,CAAC,CAAC;YACjE,CAAC;YACD,MAAM,KAAK,CAAC;QACd,CAAC;IACH,CAAC;SAAM,CAAC;QACN,QAAQ,GAAG,EAAE,KAAK,EAAE,CAAC,EAAE,kBAAkB,EAAE,EAAE,EAAE,EAAE,CAAC,EAAE,EAAE,QAAQ,EAAE,EAAE,EAAE,CAAC;IACvE,CAAC;IAED,OAAO;QACL,KAAK,EAAE,MAAM,CAAC,oBAAoB,CAAC,QAAQ,CAAC,KAAK,GAAG,QAAQ,CAAC,KAAK,EAAE,CAAC,CAAC;QACtE,KAAK,EAAE,QAAQ,CAAC,KAAK;QACrB,KAAK,EAAE,QAAQ,CAAC,KAAK;QACrB,EAAE,EAAE,QAAQ,CAAC,kBAAkB,CAAC,EAAE;QAClC,EAAE,EAAE,QAAQ,CAAC,kBAAkB,CAAC,EAAE;QAClC,QAAQ,EAAE,CAAC,GAAG,QAAQ,CAAC,QAAQ,EAAE,GAAG,QAAQ,CAAC,QAAQ,CAAC;KACvD,CAAC;AACJ,CAAC,CAAC;AAEF;;;;;;;;;GASG;AACH,MAAM,iBAAiB,GAAG,CACxB,SAA6B,EAC7B,GAAsB,EACtB,QAAkB,EAClB,EAAE;IACF,MAAM,UAAU,GAAG,IAAA,iDAAiB,EAAC,SAAS,CAAC,IAAI,CAAC,CAAC;IACrD,QAAQ,CAAC,IAAI,CAAC,GAAG,UAAU,CAAC,QAAQ,CAAC,CAAC;IAEtC,MAAM,SAAS,GAAG,GAAG,CAAC,EAAE,GAAG,SAAS,CAAC,UAAU,CAAC;IAChD,MAAM,IAAI,GAAG,IAAI,CAAC,GAAG,CAAC,CAAC,EAAE,IAAI,CAAC,KAAK,CAAC,SAAS,CAAC,CAAC,CAAC;IAEhD,IAAI,SAAS,GAAG,CAAC,EAAE,CAAC;QAClB,QAAQ,CAAC,IAAI,CAAC;YACZ,OAAO,EAAE,qBAAqB,SAAS,CAAC,UAAU,yCAAyC,GAAG,CAAC,EAAE,uEAAuE;SACzK,CAAC,CAAC;IACL,CAAC;IAED,iFAAiF;IACjF,qDAAqD;IACrD,IAAI,SAAS,CAAC,IAAI,CAAC,QAAQ,KAAK,SAAS,EAAE,CAAC;QAC1C,MAAM,UAAU,GAAG,WAAW,CAAC,kCAAkC,GAAG,SAAS,CAAC,IAAI,CAAC,QAAQ,CAAC;QAC5F,IAAI,SAAS,CAAC,UAAU,GAAG,UAAU,EAAE,CAAC;YACtC,QAAQ,CAAC,IAAI,CAAC;gBACZ,SAAS,EAAE,mBAAmB;gBAC9B,OAAO,EAAE,qBAAqB,SAAS,CAAC,UAAU,qDAAqD,UAAU,0DAA0D;aAC5K,CAAC,CAAC;QACL,CAAC;IACH,CAAC;IAED,OAAO;QACL,aAAa,EAAE,MAAM,CAAC,oBAAoB,CACxC,GAAG,CAAC,KAAK,GAAG,IAAI,GAAG,SAAS,CAAC,WAAW,GAAG,UAAU,CAAC,QAAQ,EAC9D,CAAC,CACF;QACD,IAAI;QACJ,QAAQ,EAAE,UAAU,CAAC,QAAQ;QAC7B,WAAW,EAAE,SAAS,CAAC,WAAW;KACnC,CAAC;AACJ,CAAC,CAAC;AAEF,uEAAuE;AACvE,MAAM,qBAAqB,GAAG,CAC5B,OAA4B,EAC5B,MAA2B,EAC3B,GAAsB,EACtB,QAAkB,EACZ,EAAE;IACR,QAAQ,CAAC,IAAI,CAAC;QACZ,OAAO,EACL,6MAA6M;KAChN,CAAC,CAAC;IAEH,IAAI,GAAG,CAAC,EAAE,GAAG,OAAO,CAAC,CAAC,EAAE,CAAC;QACvB,QAAQ,CAAC,IAAI,CAAC;YACZ,OAAO,EAAE,2BAA2B,GAAG,CAAC,EAAE,4CAA4C,OAAO,CAAC,CAAC,2DAA2D;SAC3J,CAAC,CAAC;IACL,CAAC;IAED,iFAAiF;IACjF,oFAAoF;IACpF,4EAA4E;IAC5E,kFAAkF;IAClF,0DAA0D;IAE1D,IAAI,GAAG,CAAC,KAAK,KAAK,CAAC,EAAE,CAAC;QACpB,QAAQ,CAAC,IAAI,CAAC;YACZ,OAAO,EACL,uLAAuL;SAC1L,CAAC,CAAC;IACL,CAAC;IAED,IAAI,MAAM,CAAC,SAAS,KAAK,SAAS,EAAE,CAAC;QACnC,QAAQ,CAAC,IAAI,CAAC;YACZ,OAAO,EACL,8IAA8I;SACjJ,CAAC,CAAC;IACL,CAAC;AACH,CAAC,CAAC;AAEF;;;;;;;;;;;;;;;GAeG;AACH,MAAM,cAAc,GAAG,CACrB,OAA4B,EAC5B,MAA2B,EAC3B,GAAsB,EACtB,SAAiB,EACjB,eAAuB,EACvB,MAAoC,EACpC,YAA2B,EAC3B,QAAkB,EAClB,EAAE;IACF,MAAM,MAAM,GAAG,qBAAqB,CAAC,OAAO,CAAC,CAAC;IAC9C,MAAM,YAAY,GAAG,CAAC,GAAG,MAAM,CAAC,QAAQ,EAAE,GAAG,QAAQ,CAAC,CAAC;IAEvD,MAAM,SAAS,GAAG,SAAS,GAAG,eAAe,GAAG,KAAK,CAAC;IACtD,MAAM,OAAO,GACX,WAAW,CAAC,kBAAkB,GAAG,IAAI,CAAC,IAAI,CAAC,OAAO,CAAC,GAAG,CAAC,GAAG,OAAO,CAAC,EAAE,GAAG,OAAO,CAAC,CAAC,GAAG,KAAK,CAAC;IAC3F,MAAM,UAAU,GAAG,OAAO,GAAG,MAAM,CAAC,EAAE,CAAC;IAEvC,IAAI,UAAU,IAAI,CAAC,EAAE,CAAC;QACpB,MAAM,IAAI,+BAAa,CAAC,wBAAM,CAAC,8BAA8B,CAAC,CAAC;IACjE,CAAC;IAED,MAAM,aAAa,GAAG,IAAI,CAAC,GAAG,CAAC,SAAS,EAAE,UAAU,CAAC,CAAC;IACtD,MAAM,kBAAkB,GAAG,aAAa,GAAG,SAAS,CAAC;IAErD,IAAI,kBAAkB,EAAE,CAAC;QACvB,YAAY,CAAC,IAAI,CAAC;YAChB,SAAS,EAAE,qBAAqB;YAChC,OAAO,EAAE,yBAAyB,MAAM,CAAC,oBAAoB,CAAC,SAAS,EAAE,CAAC,CAAC,kDAAkD,MAAM,CAAC,oBAAoB,CAAC,UAAU,EAAE,CAAC,CAAC,0DAA0D,MAAM,CAAC,oBAAoB,CAAC,OAAO,EAAE,CAAC,CAAC,qEAAqE;SAC9U,CAAC,CAAC;IACL,CAAC;IAED,iFAAiF;IACjF,oFAAoF;IACpF,+EAA+E;IAC/E,IAAI,GAAG,CAAC,aAAa,KAAK,QAAQ,IAAI,GAAG,CAAC,CAAC,KAAK,IAAI,EAAE,CAAC;QACrD,MAAM,MAAM,GAAG,IAAI,CAAC,IAAI,CAAC,OAAO,CAAC,GAAG,CAAC,CAAC;QACtC,MAAM,aAAa,GACjB,WAAW,CAAC,gCAAgC,GAAG,MAAM,GAAG,OAAO,CAAC,EAAE,GAAG,OAAO,CAAC,CAAC,GAAG,KAAK,CAAC;QACzF,MAAM,SAAS,GAAG,MAAM,CAAC,EAAE,GAAG,aAAa,GAAG,aAAa,CAAC;QAE5D,MAAM,UAAU,GAAG,SAAS;YAC1B,CAAC,CAAC,IAAI,CAAC,GAAG,CACN,WAAW,CAAC,wCAAwC,GAAG,OAAO,CAAC,CAAC,EAChE,WAAW,CAAC,2BAA2B,CACxC;YACH,CAAC,CAAC,IAAI,CAAC,GAAG,CACN,WAAW,CAAC,uCAAuC,GAAG,OAAO,CAAC,CAAC,EAC/D,WAAW,CAAC,0BAA0B,CACvC,CAAC;QAEN,IAAI,GAAG,CAAC,CAAC,GAAG,UAAU,EAAE,CAAC;YACvB,YAAY,CAAC,IAAI,CAAC;gBAChB,SAAS,EAAE,sBAAsB;gBACjC,OAAO,EAAE,gBAAgB,GAAG,CAAC,CAAC,2DAA2D,MAAM,CAAC,oBAAoB,CAAC,UAAU,EAAE,CAAC,CAAC,MAAM,SAAS,CAAC,CAAC,CAAC,gCAAgC,MAAM,CAAC,oBAAoB,CAAC,MAAM,CAAC,EAAE,GAAG,aAAa,EAAE,CAAC,CAAC,qCAAqC,MAAM,CAAC,oBAAoB,CAAC,aAAa,EAAE,CAAC,CAAC,MAAM,CAAC,CAAC,CAAC,EAAE,kEAAkE;aAC9Y,CAAC,CAAC;QACL,CAAC;IACH,CAAC;IAED,MAAM,UAAU,GAAG,MAAM,CAAC,oBAAoB,CAC5C,WAAW,CAAC,+BAA+B,GAAG,aAAa,EAC3D,CAAC,CACF,CAAC;IAEF,MAAM,SAAS,GACb,MAAM,CAAC,SAAS,KAAK,SAAS,CAAC,CAAC,CAAC,iBAAiB,CAAC,MAAM,CAAC,SAAS,EAAE,GAAG,EAAE,YAAY,CAAC,CAAC,CAAC,CAAC,IAAI,CAAC;IAEjG,MAAM,gBAAgB,GAAG,SAAS,KAAK,IAAI,IAAI,SAAS,CAAC,aAAa,GAAG,UAAU,CAAC;IACpF,MAAM,KAAK,GAAG,gBAAgB;QAC5B,CAAC,CAAE,SAAuC,CAAC,aAAa;QACxD,CAAC,CAAC,UAAU,CAAC;IAEf,IAAI,UAAU,GAAkD,eAAe,CAAC;IAChF,IAAI,gBAAgB,EAAE,CAAC;QACrB,UAAU,GAAG,WAAW,CAAC;IAC3B,CAAC;SAAM,IAAI,kBAAkB,EAAE,CAAC;QAC9B,UAAU,GAAG,aAAa,CAAC;IAC7B,CAAC;IAED,OAAO;QACL,MAAM;QACN,MAAM,EAAE;YACN,KAAK,EAAE,MAAM,CAAC,KAAK;YACnB,kBAAkB,EAAE;gBAClB,KAAK,EAAE,MAAM,CAAC,KAAK;gBACnB,KAAK,EAAE,MAAM,CAAC,KAAK;gBACnB,EAAE,EAAE,MAAM,CAAC,EAAE;gBACb,EAAE,EAAE,MAAM,CAAC,EAAE;aACd;YACD,IAAI,EAAE,IAAI;YACV,QAAQ,EAAE,MAAM,CAAC,QAAQ;SAC1B;QACD,KAAK,EAAE;YACL,KAAK,EAAE,MAAM,CAAC,oBAAoB,CAAC,MAAM,CAAC,KAAK,GAAG,KAAK,EAAE,CAAC,CAAC;YAC3D,KAAK,EAAE,MAAM,CAAC,oBAAoB,CAAC,KAAK,EAAE,CAAC,CAAC;YAC5C,UAAU;YACV,kBAAkB,EAAE;gBAClB,KAAK,EAAE,MAAM,CAAC,KAAK;gBACnB,KAAK,EAAE,MAAM,CAAC,KAAK;gBACnB,EAAE,EAAE,MAAM,CAAC,oBAAoB,CAAC,SAAS,EAAE,CAAC,CAAC;gBAC7C,WAAW,EAAE,MAAM,CAAC,oBAAoB,CAAC,aAAa,EAAE,CAAC,CAAC;gBAC1D,KAAK,EAAE,MAAM,CAAC,oBAAoB,CAAC,OAAO,EAAE,CAAC,CAAC;gBAC9C,QAAQ,EAAE,MAAM,CAAC,oBAAoB,CAAC,UAAU,EAAE,CAAC,CAAC;gBACpD,UAAU;gBACV,aAAa,EAAE,SAAS,KAAK,IAAI,CAAC,CAAC,CAAC,SAAS,CAAC,aAAa,CAAC,CAAC,CAAC,IAAI;gBAClE,aAAa,EAAE,SAAS,KAAK,IAAI,CAAC,CAAC,CAAC,SAAS,CAAC,IAAI,CAAC,CAAC,CAAC,IAAI;gBACzD,QAAQ,EAAE,SAAS,KAAK,IAAI,CAAC,CAAC,CAAC,SAAS,CAAC,QAAQ,CAAC,CAAC,CAAC,IAAI;gBACxD,KAAK,EAAE,GAAG,CAAC,KAAK;gBAChB,aAAa,EAAE,MAAM,CAAC,oBAAoB,CAAC,GAAG,CAAC,aAAa,EAAE,CAAC,CAAC;gBAChE,GAAG,YAAY;aAChB;YACD,IAAI,EAAE,IAAI;YACV,QAAQ,EAAE,YAAY;SACvB;KACF,CAAC;AACJ,CAAC,CAAC;AAEF;;;;;;;;;;;;;;;;;;;;;;;;GAwBG;AACI,MAAM,mCAAmC,GAAG,CACjD,OAA4B,EAC5B,MAA2B,EAC3B,EAAE;IACF,MAAM,QAAQ,GAAa,EAAE,CAAC;IAC9B,MAAM,GAAG,GAAG,wBAAwB,CAAC,MAAM,CAAC,CAAC;IAC7C,yBAAyB,CAAC,OAAO,EAAE,MAAM,EAAE,GAAG,CAAC,CAAC;IAChD,qBAAqB,CAAC,OAAO,EAAE,MAAM,EAAE,GAAG,EAAE,QAAQ,CAAC,CAAC;IAEtD,MAAM,IAAI,GAAG,WAAW,CAAC,6BAA6B,GAAG,GAAG,CAAC,EAAE,CAAC,CAAC,MAAM;IACvE,MAAM,SAAS,GAAG,GAAG,CAAC,KAAK,GAAG,IAAI,GAAG,GAAG,CAAC,EAAE,GAAG,GAAG,CAAC,EAAE,GAAG,GAAG,CAAC,aAAa,CAAC,CAAC,IAAI;IAE9E,iFAAiF;IACjF,oFAAoF;IACpF,MAAM,WAAW,GAAG,GAAG,CAAC,EAAE,GAAG,GAAG,CAAC,EAAE,CAAC;IACpC,MAAM,gBAAgB,GACpB,WAAW,CAAC,mCAAmC,GAAG,IAAI,CAAC,IAAI,CAAC,GAAG,CAAC,EAAE,GAAG,GAAG,CAAC,EAAE,CAAC,CAAC;IAE/E,IAAI,WAAW,GAAG,gBAAgB,EAAE,CAAC;QACnC,QAAQ,CAAC,IAAI,CAAC;YACZ,SAAS,EAAE,kBAAkB;YAC7B,OAAO,EAAE,4BAA4B,MAAM,CAAC,oBAAoB,CAAC,WAAW,EAAE,CAAC,CAAC,+BAA+B,MAAM,CAAC,oBAAoB,CAAC,gBAAgB,EAAE,CAAC,CAAC,kHAAkH;SAClR,CAAC,CAAC;IACL,CAAC;IAED,OAAO,cAAc,CACnB,OAAO,EACP,MAAM,EACN,GAAG,EACH,SAAS,EACT,GAAG,EACH,aAAa,EACb;QACE,IAAI,EAAE,MAAM,CAAC,oBAAoB,CAAC,IAAI,EAAE,CAAC,CAAC;QAC1C,WAAW,EAAE,MAAM,CAAC,oBAAoB,CAAC,WAAW,EAAE,CAAC,CAAC;QACxD,gBAAgB,EAAE,MAAM,CAAC,oBAAoB,CAAC,gBAAgB,EAAE,CAAC,CAAC;KACnE,EACD,QAAQ,CACT,CAAC;AACJ,CAAC,CAAC;AAvCW,QAAA,mCAAmC,uCAuC9C;AAEF;;;;;;;;;;;;;;;;;;;;;;;;;GAyBG;AACI,MAAM,kCAAkC,GAAG,CAChD,OAA4B,EAC5B,MAA2B,EAC3B,EAAE;IACF,MAAM,QAAQ,GAAa,EAAE,CAAC;IAC9B,MAAM,GAAG,GAAG,wBAAwB,CAAC,MAAM,CAAC,CAAC;IAC7C,yBAAyB,CAAC,OAAO,EAAE,MAAM,EAAE,GAAG,CAAC,CAAC;IAChD,qBAAqB,CAAC,OAAO,EAAE,MAAM,EAAE,GAAG,EAAE,QAAQ,CAAC,CAAC;IAEtD,MAAM,mBAAmB,GAAG,GAAG,CAAC,EAAE,GAAG,WAAW,CAAC,iCAAiC,CAAC,CAAC,MAAM;IAC1F,MAAM,GAAG,GAAG,IAAI,CAAC,GAAG,CAAC,GAAG,CAAC,EAAE,EAAE,mBAAmB,CAAC,CAAC;IAElD,IAAI,GAAG,GAAG,GAAG,CAAC,EAAE,EAAE,CAAC;QACjB,QAAQ,CAAC,IAAI,CAAC;YACZ,SAAS,EAAE,oBAAoB;YAC/B,OAAO,EAAE,qCAAqC,MAAM,CAAC,oBAAoB,CAAC,GAAG,EAAE,CAAC,CAAC,2CAA2C,GAAG,CAAC,EAAE,wCAAwC;SAC3K,CAAC,CAAC;IACL,CAAC;IAED,MAAM,WAAW,GAAG,IAAI,CAAC,GAAG,CAAC,GAAG,CAAC,QAAQ,CAAC,GAAG,IAAI,CAAC,GAAG,CAAC,GAAG,CAAC,QAAQ,CAAC,CAAC;IACpE,MAAM,SAAS,GAAG,GAAG,CAAC,KAAK,GAAG,GAAG,CAAC,EAAE,GAAG,GAAG,GAAG,GAAG,CAAC,EAAE,GAAG,GAAG,CAAC,aAAa,GAAG,WAAW,CAAC,CAAC,IAAI;IAE3F,OAAO,cAAc,CACnB,OAAO,EACP,MAAM,EACN,GAAG,EACH,SAAS,EACT,WAAW,CAAC,+BAA+B,EAC3C,YAAY,EACZ;QACE,GAAG,EAAE,MAAM,CAAC,oBAAoB,CAAC,GAAG,EAAE,CAAC,CAAC;QACxC,mBAAmB,EAAE,MAAM,CAAC,oBAAoB,CAAC,mBAAmB,EAAE,CAAC,CAAC;QACxE,WAAW,EAAE,MAAM,CAAC,oBAAoB,CAAC,WAAW,EAAE,CAAC,CAAC;QACxD,GAAG,EAAE,WAAW,CAAC,+BAA+B;KACjD,EACD,QAAQ,CACT,CAAC;AACJ,CAAC,CAAC;AArCW,QAAA,kCAAkC,sCAqC7C;AAEF;;;;;;;;;;GAUG;AACI,MAAM,6BAA6B,GAAG,CAC3C,OAA4B,EAC5B,MAA2B,EAC3B,EAAE;IACF,MAAM,WAAW,GAAG,IAAA,2CAAmC,EAAC,OAAO,EAAE,MAAM,CAAC,CAAC;IACzE,MAAM,UAAU,GAAG,IAAA,0CAAkC,EAAC,OAAO,EAAE,MAAM,CAAC,CAAC;IAEvE,MAAM,SAAS,GAAG,UAAU,CAAC,KAAK,CAAC,KAAK,GAAG,WAAW,CAAC,KAAK,CAAC,KAAK,CAAC,CAAC,CAAC,UAAU,CAAC,CAAC,CAAC,WAAW,CAAC;IAE9F,OAAO;QACL,WAAW;QACX,UAAU;QACV,SAAS,EAAE;YACT,MAAM,EAAE,SAAS,CAAC,MAAM;YACxB,KAAK,EAAE,SAAS,CAAC,KAAK,CAAC,KAAK;YAC5B,KAAK,EAAE,SAAS,CAAC,KAAK,CAAC,KAAK;YAC5B,UAAU,EAAE,SAAS,CAAC,KAAK,CAAC,UAAU;SACvC;KACF,CAAC;AACJ,CAAC,CAAC;AAnBW,QAAA,6BAA6B,iCAmBxC"}

package/package.json

@@ -1,6 +1,6 @@
 {
   "name": "@theerapat-s28/ts-structural-eng-tools",
-  "version": "1.4.0",
+  "version": "1.5.0",
   "description": "TypeScript structural-engineering helper functions and beam design utilities",
   "main": "dist/index.js",
   "types": "dist/index.d.ts",