@oimlsmart/primmel-packages 0.9.0 → 0.11.0

package/oiml-r129/model/conditions.prl

@@ -21,3 +21,9 @@ condition_set multi-dimensional-instrument-rated-conditions {
   ref derives-from "urn:oiml:pub:r:129-1:2020#clause-4.2.1"
 }
 
+common_test_condition dimensional-performance-tests {
+  title "Performance test conditions"
+  reference "urn:oiml:pub:r:129-2:2020#clause-A"
+  description "Test objects of known dimensions covering the measuring range; the zero or ready condition set before each measurement series; reference conditions 20 °C ± 5 °C and (50 ± 15) % RH unless the procedure states otherwise."
+}
+

package/oiml-r144/model/conditions.prl

@@ -44,3 +44,57 @@ condition_set gas-analytical-system-limiting-conditions {
   ref derives-from "urn:oiml:pub:r:144-1:2013#clause-8.8"
 }
 
+common_test_condition calibration-before-tests {
+  title "Calibration before type evaluation tests"
+  reference "urn:oiml:pub:r:144-1:2013#clause-8"
+  description "Prior to the type evaluation tests, or when specified by the manufacturer, the gas analytical system shall be calibrated against the calibration gas mixture (CGM) according to the operating manual procedures and under reference conditions (if not specified otherwise)."
+}
+
+common_test_condition cgm-composition {
+  title "CGM composition and certification"
+  reference "urn:oiml:pub:r:144-1:2013#clause-A"
+  description "CGMs shall be supplied from a gas cylinder under pressure or a gas mixture generator (ISO 6142, ISO 6143, ISO 6145-1), certified with composition uncertainty of 2 % or less of the certified value for the components to be determined (3 % for other components), blend tolerance not exceeding 10 %, traceable to (inter)national gaseous measurement standards (R 144-1, Annex A.1, A.2)."
+}
+
+common_test_condition cgm-test-points {
+  title "CGM test points for error determination"
+  reference "urn:oiml:pub:r:144-1:2013#clause-A.1.4"
+  description "For error determination, three binary gas mixtures at (5 + 5) %, (50 + 5) % and (95 - 5) % of the measuring range are used (R 144-1, A.1.4); R 144-2, 1.2 recommends minimum +10 %, average ±10 %, maximum -10 % for linear calibration characteristics (at least five uniformly distributed points for nonlinear). Three-component mixtures CO + NO + N2 and CO + NO2 + N2 are permitted (A.1.4 NOTE)."
+}
+
+common_test_condition cgm-uncertainty-ratio {
+  title "CGM uncertainty ratio"
+  reference "urn:oiml:pub:r:144-1:2013#clause-7.2.2.2"
+  description "The ratio between the absolute value of the uncertainty of the CGM and the maximum permissible error of the gas analytical system at the given point of the measurement range shall be not more than 1:3 (the responsible legal authority may allow 1:2)."
+}
+
+common_test_condition zero-gas {
+  title "Zero gas"
+  reference "urn:oiml:pub:r:144-1:2013#clause-A.3"
+  description "Ambient air drawn through a charcoal filter or equivalent system, or high pure nitrogen directly, is used to set zero (R 144-1, A.3; 5.1.4)."
+}
+
+common_test_condition cgm-supply-pressure {
+  title "CGM supply pressure"
+  reference "urn:oiml:pub:r:144-2:2013#clause-1.5.2"
+  description "The calibration gas mixture shall be supplied to the sampling probe at ambient pressure with a deviation of ±0.8 kPa (±750 Pa for the response time test, R 144-2, 1.20.1)."
+}
+
+common_test_condition single-influence-quantity {
+  title "One influence quantity at a time"
+  reference "urn:oiml:pub:r:144-1:2013#clause-8.4"
+  description "Only one influence quantity shall be varied during a test, while all others are maintained at their reference values."
+}
+
+common_test_condition separate-units-testing {
+  title "Testing of separate units"
+  reference "urn:oiml:pub:r:144-1:2013#clause-7.1.3.1"
+  description "Tests should be carried out with a completely mounted gas analytical system; tests on separate units or devices are permitted when testing the system as a whole is impossible due to size or configuration, provided the operating conditions for that unit can be simulated. Separate components shall not be dismantled for testing."
+}
+
+common_test_condition leak-check-before-measurement {
+  title "Leak check before measurement"
+  reference "urn:oiml:pub:r:144-2:2013#clause-B.3"
+  description "A leak check of the gas handling system shall be performed at least once a day and after each disassembly; any leakage shall be repaired and a successful leak check performed before measurement (R 144-2, Annex B.3, B.4)."
+}
+

package/oiml-r60/model/conditions.prl

@@ -48,3 +48,111 @@ condition_set load-cell-limiting-conditions {
   ref derives-from "urn:oiml:pub:r:60-1:2021#clause-3.5.16"
 }
 
+common_test_condition test-equipment {
+  title "Test equipment"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.2"
+  description "Test equipment used for the tests shall be calibrated and traceable to national or international standards. The equipment shall have adequate precision for the measurements to be performed."
+}
+
+common_test_condition environmental-conditions {
+  title "Environmental conditions"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.1"
+  description "The test shall be conducted under stable ambient conditions as specified in R 60-2 §2.6.1."
+}
+
+common_test_condition acceleration-of-gravity {
+  title "Acceleration of gravity"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.2"
+  description "The value of the acceleration of gravity used in the calculation of the force applied shall be the local value or the value declared for the testing laboratory."
+}
+
+common_test_condition loading-conditions {
+  title "Loading conditions"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.3"
+  description "Loads shall be applied axially and without shock. The points of force application shall be defined for each load direction (compression, tension, beam)."
+}
+
+common_test_condition measuring-range-limits {
+  title "Measuring range limits"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.4"
+  description "Tests shall be conducted within the measuring range defined by D_min and D_max of the load cell under test."
+}
+
+common_test_condition reference-standards {
+  title "Reference standards"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.5"
+  description "Reference standards of mass (or force) used for calibration shall have an uncertainty appropriate to the measurements."
+}
+
+common_test_condition stabilisation-period {
+  title "Stabilisation period"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.6"
+  description "A stabilisation period shall be allowed after changing temperature or load before recording indications."
+}
+
+common_test_condition temperature-conditions {
+  title "Temperature conditions"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.7"
+  description "Tests shall be conducted at the temperatures specified in R 60-2 §2.10 (typically 20°C reference plus T_high and T_low). Temperature is considered stable when the difference between extreme temperatures noted during the test does not exceed one fifth of the temperature range of the load cell under test, without being greater than 2 °C (R 60-2, 2.7.3.1)."
+}
+
+common_test_condition barometric-pressure-effects {
+  title "Barometric pressure effects"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.8"
+  description "Atmospheric pressure changes shall be recorded during the test for correction of barometric-pressure-sensitive readings."
+}
+
+common_test_condition humidity-effects-condition {
+  title "Humidity effects"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.9"
+  description "Humidity shall be controlled per the test specification (typically 50% RH for non-humidity tests, cyclic or steady-state for humidity tests)."
+}
+
+common_test_condition indicating-instrument-checking {
+  title "Indicating instrument checking"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.10"
+  description "The indicating instrument used to read the load cell output shall be checked for accuracy before each test series."
+}
+
+common_test_condition other-conditions {
+  title "Other conditions"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.11"
+  description "Any other conditions specified by the manufacturer or by the testing laboratory's procedures."
+}
+
+common_test_condition time-date-format {
+  title "Time and date format"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.7.3.12"
+  description "All time and date recordings shall use ISO 8601 format."
+}
+
+common_test_condition errors-conditions {
+  title "Conditions for error determination"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.8.1"
+  description "Conditions for the determination of measurement errors shall be as specified in R 60-2 §2.7."
+}
+
+common_test_condition errors-limits {
+  title "Limits of error"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.8.2"
+  description "The MPE values per R 60-1 §5.3 shall be used as the limits of error during type evaluation."
+}
+
+common_test_condition initial-readings {
+  title "Initial readings"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.8.3"
+  description "Initial minimum test load indications shall be recorded before each test series."
+}
+
+common_test_condition loading-unloading-times {
+  title "Loading/unloading times"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.8.3.1"
+  description "Loading and unloading shall be performed smoothly without shock. Times for loading and unloading shall be recorded."
+}
+
+common_test_condition loading-times-adherence {
+  title "Adherence to loading/unloading times"
+  reference "urn:oiml:pub:r:60-2:2021#clause-2.8.3.2"
+  description "Loading/unloading times per R 60-2, Table 1. When the specified times cannot be achieved the applicant shall be consulted; for the minimum dead load output return test the time may be increased from 100 % to a limit of 150 % of the specified time, provided the permissible variation of the result is proportionally reduced from 100 % to 50 % (C_DR <= 0.5(1-(x-1)) v, R 60-3, 2.1.5.6)."
+}
+

package/oiml-r60/specification/symbols.prl

@@ -597,3 +597,13 @@ symbol fault {
   ref derives-from "urn:oiml:pub:r:60-1:2021#clause-5.7.2.5"
 }
 
+formula_note note-1 {
+  text "Observe extreme caution by referring to calculation procedure for correct application of these formulae."
+  applies_to { c_c c_c_30_20 c_dr c_hmax c_hmin c_m c_p dr e_l e_r conversion_factor_f r_i }
+}
+
+formula_note note-2 {
+  text "Use with initial 20 °C ascending load run only. Refer to R 60-2, 2.8.2."
+  applies_to { conversion_factor_f }
+}
+

package/oiml-r91/model/conditions.prl

@@ -1,3 +1,11 @@
+# OIML R 91 — common_test_conditions register note (the YAML twin's
+# register-level `note`, metadata prose with no construct home):
+# R 91-2 structures tests as: documentation/visual inspection;
+# rated-condition and linearity tests at reference conditions;
+# influence-factor tests per Table 1 points A-H; disturbance tests;
+# category-specific tests incl. moving metrological FIELD tests with real
+# traffic and dynamic performance tests via traffic simulation. Field tests
+# require a reference speed meter or simulator (v_ref, unrounded).
 condition_set speed-meter-reference {
   role reference
   description "Reference conditions for linearity and type-evaluation measurements (R 91-2, 6.2; all influence quantities minimized). Temperature and humidity shall not vary by more than 5 °C and 30 % RH within the reference intervals during a test."
@@ -35,3 +43,19 @@ condition_set speed-meter-limiting {
   ref derives-from "urn:oiml:pub:r:91-1:2025#clause-6.16"
 }
 
+common_test_condition measurement_counts {
+  description "Minimum valid measurements per test context (R 91-2, 4.4/5.3/7.7.1; see tables.yaml measurement_counts)."
+  source {
+    doc "urn:oiml:pub:r:91-3:2025"
+    clause "symbols"
+  }
+}
+
+common_test_condition reference_speed_meter {
+  description "Reference speed measurement by reference speed meter or simulator (R 91-3 symbols: v_ref), used unrounded with sufficient significant digits (R 91-1, 6.3 Note)."
+  source {
+    doc "urn:oiml:pub:r:91-1:2025"
+    clause "6.3"
+  }
+}
+

package/package.json

@@ -1,6 +1,6 @@
 {
   "name": "@oimlsmart/primmel-packages",
-  "version": "0.9.0",
+  "version": "0.11.0",
   "description": "The OIML SMART platform's authoritative model content: every Recommendation, the OIML-CS scheme, the CASCO foundations, the shared modules, and the product/program reference packages as Primmel (.prl) packages — the single source of truth the platform's data trees regenerate from. Consumed by the smart monorepo (oimlsmart/smart) at a pinned version (TODO.repos/02).",
   "type": "module",
   "repository": {

package/oiml-r129/payload/conditions-common-test.yaml

@@ -1,8 +0,0 @@
-# GENERATED package payload (task 31b) — content with no PRL construct; composed back by regenerate-data + build-primmel-cache. Do not edit by hand.
-common_test_conditions:
-  - id: dimensional-performance-tests
-    title: Performance test conditions
-    reference: urn:oiml:pub:r:129-2:2020#clause-A
-    description: >
-      Test objects of known dimensions covering the measuring range; the zero or ready condition set before each
-      measurement series; reference conditions 20 °C ± 5 °C and (50 ± 15) % RH unless the procedure states otherwise.

package/oiml-r144/payload/conditions-common-test.yaml

@@ -1,74 +0,0 @@
-# GENERATED package payload (task 31b) — content with no PRL construct; composed back by regenerate-data + build-primmel-cache. Do not edit by hand.
-common_test_conditions:
-  - id: calibration-before-tests
-    title: Calibration before type evaluation tests
-    reference: urn:oiml:pub:r:144-1:2013#clause-8
-    description: |
-      Prior to the type evaluation tests, or when specified by the manufacturer,
-      the gas analytical system shall be calibrated against the calibration gas
-      mixture (CGM) according to the operating manual procedures and under
-      reference conditions (if not specified otherwise).
-  - id: cgm-composition
-    title: CGM composition and certification
-    reference: urn:oiml:pub:r:144-1:2013#clause-A
-    description: |
-      CGMs shall be supplied from a gas cylinder under pressure or a gas
-      mixture generator (ISO 6142, ISO 6143, ISO 6145-1), certified with
-      composition uncertainty of 2 % or less of the certified value for the
-      components to be determined (3 % for other components), blend tolerance
-      not exceeding 10 %, traceable to (inter)national gaseous measurement
-      standards (R 144-1, Annex A.1, A.2).
-  - id: cgm-test-points
-    title: CGM test points for error determination
-    reference: urn:oiml:pub:r:144-1:2013#clause-A.1.4
-    description: |
-      For error determination, three binary gas mixtures at (5 + 5) %,
-      (50 + 5) % and (95 - 5) % of the measuring range are used (R 144-1,
-      A.1.4); R 144-2, 1.2 recommends minimum +10 %, average ±10 %, maximum
-      -10 % for linear calibration characteristics (at least five uniformly
-      distributed points for nonlinear). Three-component mixtures
-      CO + NO + N2 and CO + NO2 + N2 are permitted (A.1.4 NOTE).
-  - id: cgm-uncertainty-ratio
-    title: CGM uncertainty ratio
-    reference: urn:oiml:pub:r:144-1:2013#clause-7.2.2.2
-    description: |
-      The ratio between the absolute value of the uncertainty of the CGM and
-      the maximum permissible error of the gas analytical system at the given
-      point of the measurement range shall be not more than 1:3 (the
-      responsible legal authority may allow 1:2).
-  - id: zero-gas
-    title: Zero gas
-    reference: urn:oiml:pub:r:144-1:2013#clause-A.3
-    description: |
-      Ambient air drawn through a charcoal filter or equivalent system, or
-      high pure nitrogen directly, is used to set zero (R 144-1, A.3; 5.1.4).
-  - id: cgm-supply-pressure
-    title: CGM supply pressure
-    reference: urn:oiml:pub:r:144-2:2013#clause-1.5.2
-    description: |
-      The calibration gas mixture shall be supplied to the sampling probe at
-      ambient pressure with a deviation of ±0.8 kPa (±750 Pa for the response
-      time test, R 144-2, 1.20.1).
-  - id: single-influence-quantity
-    title: One influence quantity at a time
-    reference: urn:oiml:pub:r:144-1:2013#clause-8.4
-    description: |
-      Only one influence quantity shall be varied during a test, while all
-      others are maintained at their reference values.
-  - id: separate-units-testing
-    title: Testing of separate units
-    reference: urn:oiml:pub:r:144-1:2013#clause-7.1.3.1
-    description: |
-      Tests should be carried out with a completely mounted gas analytical
-      system; tests on separate units or devices are permitted when testing
-      the system as a whole is impossible due to size or configuration,
-      provided the operating conditions for that unit can be simulated.
-      Separate components shall not be dismantled for testing.
-  - id: leak-check-before-measurement
-    title: Leak check before measurement
-    reference: urn:oiml:pub:r:144-2:2013#clause-B.3
-    description: |
-      A leak check of the gas handling system shall be performed at least
-      once a day and after each disassembly; any leakage shall be repaired
-      and a successful leak check performed before measurement (R 144-2,
-      Annex B.3, B.4).

package/oiml-r60/payload/conditions-common-test.yaml

@@ -1,121 +0,0 @@
-# GENERATED package payload (task 31b) — content with no PRL construct; composed back by regenerate-data + build-primmel-cache. Do not edit by hand.
-common_test_conditions:
-  - id: test-equipment
-    title: Test equipment
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.2
-    description: |
-      Test equipment used for the tests shall be calibrated and
-      traceable to national or international standards. The equipment
-      shall have adequate precision for the measurements to be performed.
-  - id: environmental-conditions
-    title: Environmental conditions
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.1
-    description: |
-      The test shall be conducted under stable ambient conditions as
-      specified in R 60-2 §2.6.1.
-  - id: acceleration-of-gravity
-    title: Acceleration of gravity
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.2
-    description: |
-      The value of the acceleration of gravity used in the calculation
-      of the force applied shall be the local value or the value
-      declared for the testing laboratory.
-  - id: loading-conditions
-    title: Loading conditions
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.3
-    description: |
-      Loads shall be applied axially and without shock. The points of
-      force application shall be defined for each load direction
-      (compression, tension, beam).
-  - id: measuring-range-limits
-    title: Measuring range limits
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.4
-    description: |
-      Tests shall be conducted within the measuring range defined by
-      D_min and D_max of the load cell under test.
-  - id: reference-standards
-    title: Reference standards
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.5
-    description: |
-      Reference standards of mass (or force) used for calibration
-      shall have an uncertainty appropriate to the measurements.
-  - id: stabilisation-period
-    title: Stabilisation period
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.6
-    description: |
-      A stabilisation period shall be allowed after changing
-      temperature or load before recording indications.
-  - id: temperature-conditions
-    title: Temperature conditions
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.7
-    description: |
-      Tests shall be conducted at the temperatures specified in
-      R 60-2 §2.10 (typically 20°C reference plus T_high and T_low).
-      Temperature is considered stable when the difference between
-      extreme temperatures noted during the test does not exceed one
-      fifth of the temperature range of the load cell under test,
-      without being greater than 2 °C (R 60-2, 2.7.3.1).
-  - id: barometric-pressure-effects
-    title: Barometric pressure effects
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.8
-    description: |
-      Atmospheric pressure changes shall be recorded during the test
-      for correction of barometric-pressure-sensitive readings.
-  - id: humidity-effects-condition
-    title: Humidity effects
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.9
-    description: |
-      Humidity shall be controlled per the test specification
-      (typically 50% RH for non-humidity tests, cyclic or steady-state
-      for humidity tests).
-  - id: indicating-instrument-checking
-    title: Indicating instrument checking
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.10
-    description: |
-      The indicating instrument used to read the load cell output
-      shall be checked for accuracy before each test series.
-  - id: other-conditions
-    title: Other conditions
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.11
-    description: |
-      Any other conditions specified by the manufacturer or by the
-      testing laboratory's procedures.
-  - id: time-date-format
-    title: Time and date format
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.7.3.12
-    description: |
-      All time and date recordings shall use ISO 8601 format.
-  - id: errors-conditions
-    title: Conditions for error determination
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.8.1
-    description: |
-      Conditions for the determination of measurement errors shall
-      be as specified in R 60-2 §2.7.
-  - id: errors-limits
-    title: Limits of error
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.8.2
-    description: |
-      The MPE values per R 60-1 §5.3 shall be used as the limits
-      of error during type evaluation.
-  - id: initial-readings
-    title: Initial readings
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.8.3
-    description: |
-      Initial minimum test load indications shall be recorded before
-      each test series.
-  - id: loading-unloading-times
-    title: Loading/unloading times
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.8.3.1
-    description: |
-      Loading and unloading shall be performed smoothly without shock.
-      Times for loading and unloading shall be recorded.
-  - id: loading-times-adherence
-    title: Adherence to loading/unloading times
-    reference: urn:oiml:pub:r:60-2:2021#clause-2.8.3.2
-    description: |
-      Loading/unloading times per R 60-2, Table 1. When the specified
-      times cannot be achieved the applicant shall be consulted; for the
-      minimum dead load output return test the time may be increased from
-      100 % to a limit of 150 % of the specified time, provided the
-      permissible variation of the result is proportionally reduced from
-      100 % to 50 % (C_DR <= 0.5(1-(x-1)) v, R 60-3, 2.1.5.6).

package/oiml-r60/payload/symbols-formula-notes.yaml

@@ -1,21 +0,0 @@
-# GENERATED package payload (task 31b) — content with no PRL construct; composed back by regenerate-data + build-primmel-cache. Do not edit by hand.
-formula_notes:
-  - id: note-1
-    text: Observe extreme caution by referring to calculation procedure for correct application of these formulae.
-    applies_to:
-      - c_c
-      - c_c_30_20
-      - c_dr
-      - c_hmax
-      - c_hmin
-      - c_m
-      - c_p
-      - dr
-      - e_l
-      - e_r
-      - conversion_factor_f
-      - r_i
-  - id: note-2
-    text: Use with initial 20 °C ascending load run only. Refer to R 60-2, 2.8.2.
-    applies_to:
-      - conversion_factor_f

package/oiml-r91/payload/conditions-common-test.yaml

@@ -1,19 +0,0 @@
-# GENERATED package payload (task 31b) — content with no PRL construct; composed back by regenerate-data + build-primmel-cache. Do not edit by hand.
-common_test_conditions:
-  measurement_counts:
-    description: Minimum valid measurements per test context (R 91-2, 4.4/5.3/7.7.1; see tables.yaml measurement_counts).
-    source:
-      clause: symbols
-      doc: urn:oiml:pub:r:91-3:2025
-  note: >
-    R 91-2 structures tests as: documentation/visual inspection; rated-condition and linearity tests at reference
-    conditions; influence-factor tests per Table 1 points A-H; disturbance tests; category-specific tests incl. moving
-    metrological FIELD tests with real traffic and dynamic performance tests via traffic simulation. Field tests require
-    a reference speed meter or simulator (v_ref, unrounded).
-  reference_speed_meter:
-    description: >-
-      Reference speed measurement by reference speed meter or simulator (R 91-3 symbols: v_ref), used unrounded with
-      sufficient significant digits (R 91-1, 6.3 Note).
-    source:
-      clause: '6.3'
-      doc: urn:oiml:pub:r:91-1:2025