@kvaser/canking-api 7.3.0 → 7.4.0

package/doc_md/models/enumerations/CanFrameFlag.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 
@@ -14,144 +14,211 @@ Possible CAN frame flags. The flag value must match the canlib flag value.
 
 > **CAN\_FRAME\_FLAG\_ABL**: `67108864`
 
+CAN_FRAME_FLAG_ABL - Only together with TxNack, Single shot message was not sent because arbitration was lost.
+This flag is only used with received messages.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_DELAY\_MSG
 
 > **CAN\_FRAME\_FLAG\_DELAY\_MSG**: `256`
 
+CAN_FRAME_FLAG_DELAY_MSG - Message is NOT sent on the bus. The transmission of messages are delayed.
+The dlc specifies the delay in milliseconds (1..1000).
+
 ***
 
 ### CAN\_FRAME\_FLAG\_ERR\_BIT0
 
 > **CAN\_FRAME\_FLAG\_ERR\_BIT0**: `16384`
 
+CAN_FRAME_FLAG_ERR_BIT0 - Sent dominant, read recessive.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_ERR\_BIT1
 
 > **CAN\_FRAME\_FLAG\_ERR\_BIT1**: `32768`
 
+CAN_FRAME_FLAG_ERR_BIT1 - Sent recessive, read dominant.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_ERR\_CRC
 
 > **CAN\_FRAME\_FLAG\_ERR\_CRC**: `8192`
 
+CAN_FRAME_FLAG_ERR_CRC - CRC error.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_ERR\_FORM
 
 > **CAN\_FRAME\_FLAG\_ERR\_FORM**: `4096`
 
+CAN_FRAME_FLAG_ERR_FORM - Form error.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_ERR\_HW\_OVERRUN
 
 > **CAN\_FRAME\_FLAG\_ERR\_HW\_OVERRUN**: `512`
 
+CAN_FRAME_FLAG_ERR_HW_OVERRUN - HW buffer overrun.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_ERR\_STUFF
 
 > **CAN\_FRAME\_FLAG\_ERR\_STUFF**: `2048`
 
+CAN_FRAME_FLAG_ERR_STUFF - Stuff error.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_ERR\_SW\_OVERRUN
 
 > **CAN\_FRAME\_FLAG\_ERR\_SW\_OVERRUN**: `1024`
 
+CAN_FRAME_FLAG_ERR_SW_OVERRUN - SW buffer overrun.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_ERROR\_FRAME
 
 > **CAN\_FRAME\_FLAG\_ERROR\_FRAME**: `32`
 
+CAN_FRAME_FLAG_ERROR_FRAME - Message represents an error frame.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_EXT
 
 > **CAN\_FRAME\_FLAG\_EXT**: `4`
 
+CAN_FRAME_FLAG_EXT - Message has an extended (29-bit) identifier.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_FD\_BRS
 
 > **CAN\_FRAME\_FLAG\_FD\_BRS**: `131072`
 
+CAN_FRAME_FLAG_FD_BRS - Message is sent/received with bit rate switch (CAN FD).
+
 ***
 
 ### CAN\_FRAME\_FLAG\_FD\_ESI
 
 > **CAN\_FRAME\_FLAG\_FD\_ESI**: `262144`
 
+CAN_FRAME_FLAG_FD_ESI - Sender of the message is in error passive mode (CAN FD).
+
 ***
 
 ### CAN\_FRAME\_FLAG\_FD\_FDF
 
 > **CAN\_FRAME\_FLAG\_FD\_FDF**: `65536`
 
+CAN_FRAME_FLAG_FD_FDF - Message is an FD message (CAN FD).
+
 ***
 
 ### CAN\_FRAME\_FLAG\_LOCAL\_TXACK
 
 > **CAN\_FRAME\_FLAG\_LOCAL\_TXACK**: `268435456`
 
+CAN_FRAME_FLAG_LOCAL_TXACK - Message was sent from another handle on the same can channel.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_NERR
 
 > **CAN\_FRAME\_FLAG\_NERR**: `16`
 
+CAN_FRAME_FLAG_NERR - NERR was active during the message (TJA1054 hardware).
+
 ***
 
 ### CAN\_FRAME\_FLAG\_RTR
 
 > **CAN\_FRAME\_FLAG\_RTR**: `1`
 
+CAN_FRAME_FLAG_RTR - Message is a remote request, only valid for classic CAN.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_SINGLE\_SHOT
 
 > **CAN\_FRAME\_FLAG\_SINGLE\_SHOT**: `16777216`
 
+CAN_FRAME_FLAG_SINGLE_SHOT - Message is Single Shot, try to send once, no retransmission.
+This flag can only be used with transmitted messages.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_STD
 
 > **CAN\_FRAME\_FLAG\_STD**: `2`
 
+CAN_FRAME_FLAG_STD - Message has a standard (11-bit) identifier.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_TXACK
 
 > **CAN\_FRAME\_FLAG\_TXACK**: `64`
 
+CAN_FRAME_FLAG_TXACK - Message is a TX ACK (msg has really been sent).
+
 ***
 
 ### CAN\_FRAME\_FLAG\_TXNACK
 
 > **CAN\_FRAME\_FLAG\_TXNACK**: `33554432`
 
+CAN_FRAME_FLAG_TXNACK - Message is a failed Single Shot, message was not sent. This flag is only used with received messages.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_TXRQ
 
 > **CAN\_FRAME\_FLAG\_TXRQ**: `128`
 
+CAN_FRAME_FLAG_TXRQ - Message is a TX REQUEST (msg was transfered to the chip).
+
 ***
 
 ### CAN\_FRAME\_FLAG\_UNSPECIFIED
 
 > **CAN\_FRAME\_FLAG\_UNSPECIFIED**: `0`
 
+CAN_FRAME_FLAG_UNSPECIFIED - No flag has been set.
+
 ***
 
 ### CAN\_FRAME\_FLAG\_WAKEUP
 
 > **CAN\_FRAME\_FLAG\_WAKEUP**: `8`
 
+CAN_FRAME_FLAG_WAKEUP - Message is a WAKEUP message (SWC hardware.)
+
+***
+
+### CAN\_FRAME\_FLAG\_XL\_VCID
+
+> **CAN\_FRAME\_FLAG\_XL\_VCID**: `2097152`
+
+CAN_FRAME_FLAG_XL_VCID - CAN XL Virtual CAN network ID (VCID). (Not currently part of CanLib, the value can change in future releases.)
+
+***
+
+### CAN\_FRAME\_FLAG\_XL\_XLF
+
+> **CAN\_FRAME\_FLAG\_XL\_XLF**: `1048576`
+
+CAN_FRAME_FLAG_XL_XLF - CAN XL frame. (Not currently part of CanLib, the value can change in future releases.)
+
 ***
 
 ### UNRECOGNIZED

package/doc_md/models/enumerations/CanMessageFilterType.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 
@@ -14,12 +14,16 @@ Possible CAN message filter types.
 
 > **CAN\_MESSAGE\_FILTER\_TYPE\_BLOCK**: `2`
 
+CAN_MESSAGE_FILTER_TYPE_BLOCK - Block listed messages.
+
 ***
 
 ### CAN\_MESSAGE\_FILTER\_TYPE\_PASS
 
 > **CAN\_MESSAGE\_FILTER\_TYPE\_PASS**: `1`
 
+CAN_MESSAGE_FILTER_TYPE_PASS - Pass listed messages.
+
 ***
 
 ### CAN\_MESSAGE\_FILTER\_TYPE\_UNSPECIFIED

package/doc_md/models/enumerations/CanMode.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 
@@ -14,18 +14,32 @@ Possible CAN modes.
 
 > **CAN\_MODE\_CAN**: `1`
 
+CAN_MODE_CAN - Classic CAN mode.
+
 ***
 
 ### CAN\_MODE\_CAN\_FD
 
 > **CAN\_MODE\_CAN\_FD**: `2`
 
+CAN_MODE_CAN_FD - CAN FD mode.
+
 ***
 
 ### CAN\_MODE\_CAN\_FD\_NONISO
 
 > **CAN\_MODE\_CAN\_FD\_NONISO**: `3`
 
+CAN_MODE_CAN_FD_NONISO - CAN FD non-ISO mode.
+
+***
+
+### CAN\_MODE\_CAN\_XL
+
+> **CAN\_MODE\_CAN\_XL**: `4`
+
+CAN_MODE_CAN_XL - CAN XL mode.
+
 ***
 
 ### CAN\_MODE\_UNSPECIFIED

package/doc_md/models/enumerations/DecimalChar.md

@@ -0,0 +1,37 @@
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
+
+***
+
+[Kvaser CanKing GUI Extensions SDK](../../modules.md) / [models](../README.md) / DecimalChar
+
+# Enumeration: DecimalChar
+
+Possible decimal separators for loggers.
+
+## Enumeration Members
+
+### DECIMAL\_CHAR\_DEC\_COMMA
+
+> **DECIMAL\_CHAR\_DEC\_COMMA**: `2`
+
+DECIMAL_CHAR_DEC_COMMA - Comma (,) separator
+
+***
+
+### DECIMAL\_CHAR\_DEC\_DOT
+
+> **DECIMAL\_CHAR\_DEC\_DOT**: `1`
+
+DECIMAL_CHAR_DEC_DOT - Dot (.) separator
+
+***
+
+### DECIMAL\_CHAR\_UNSPECIFIED
+
+> **DECIMAL\_CHAR\_UNSPECIFIED**: `0`
+
+***
+
+### UNRECOGNIZED
+
+> **UNRECOGNIZED**: `-1`

package/doc_md/models/enumerations/FileConflictAction.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 
@@ -14,18 +14,24 @@ Possible actions to use if a log file already exists with the same name.
 
 > **FILE\_CONFLICT\_ACTION\_APPEND\_INDEX**: `2`
 
+FILE_CONFLICT_ACTION_APPEND_INDEX - Append an index to the file name.
+
 ***
 
 ### FILE\_CONFLICT\_ACTION\_APPEND\_TIMESTAMP
 
 > **FILE\_CONFLICT\_ACTION\_APPEND\_TIMESTAMP**: `3`
 
+FILE_CONFLICT_ACTION_APPEND_TIMESTAMP - Append a timestamp to the file name.
+
 ***
 
 ### FILE\_CONFLICT\_ACTION\_OVERWRITE
 
 > **FILE\_CONFLICT\_ACTION\_OVERWRITE**: `1`
 
+FILE_CONFLICT_ACTION_OVERWRITE - Overwrite the existing file.
+
 ***
 
 ### FILE\_CONFLICT\_ACTION\_UNSPECIFIED

package/doc_md/models/enumerations/LinFrameFlag.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 
@@ -14,54 +14,72 @@ Possible LIN frame flags. The flag value must match the linlib flag value.
 
 > **LIN\_FRAME\_FLAG\_BIT\_ERROR**: `128`
 
+LIN_FRAME_FLAG_BIT_ERROR - Bit error when transmitting.
+
 ***
 
 ### LIN\_FRAME\_FLAG\_CSUM\_ERROR
 
 > **LIN\_FRAME\_FLAG\_CSUM\_ERROR**: `16`
 
+LIN_FRAME_FLAG_CSUM_ERROR - Checksum error.
+
 ***
 
 ### LIN\_FRAME\_FLAG\_NODATA
 
 > **LIN\_FRAME\_FLAG\_NODATA**: `8`
 
+LIN_FRAME_FLAG_NODATA - No data, only a header.
+
 ***
 
 ### LIN\_FRAME\_FLAG\_PARITY\_ERROR
 
 > **LIN\_FRAME\_FLAG\_PARITY\_ERROR**: `32`
 
+LIN_FRAME_FLAG_PARITY_ERROR - ID parity error.
+
 ***
 
 ### LIN\_FRAME\_FLAG\_RX
 
 > **LIN\_FRAME\_FLAG\_RX**: `2`
 
+LIN_FRAME_FLAG_RX - The message was something we received from the bus.
+
 ***
 
 ### LIN\_FRAME\_FLAG\_SYNCH\_ERROR
 
 > **LIN\_FRAME\_FLAG\_SYNCH\_ERROR**: `64`
 
+LIN_FRAME_FLAG_SYNCH_ERROR - A synch error.
+
 ***
 
 ### LIN\_FRAME\_FLAG\_TX
 
 > **LIN\_FRAME\_FLAG\_TX**: `1`
 
+LIN_FRAME_FLAG_TX - The message was something we transmitted to the bus.
+
 ***
 
 ### LIN\_FRAME\_FLAG\_UNSPECIFIED
 
 > **LIN\_FRAME\_FLAG\_UNSPECIFIED**: `0`
 
+LIN_FRAME_FLAG_UNSPECIFIED - No flag has been set.
+
 ***
 
 ### LIN\_FRAME\_FLAG\_WAKEUP\_FRAME
 
 > **LIN\_FRAME\_FLAG\_WAKEUP\_FRAME**: `4`
 
+LIN_FRAME_FLAG_WAKEUP_FRAME - A wake up frame was received. Id/msg/dlc are undefined.
+
 ***
 
 ### UNRECOGNIZED

package/doc_md/models/enumerations/LogFileFormat.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 
@@ -92,6 +92,14 @@ LOG_FILE_FORMAT_KME50 - Input and output file format.
 
 ***
 
+### LOG\_FILE\_FORMAT\_KME60
+
+> **LOG\_FILE\_FORMAT\_KME60**: `10`
+
+LOG_FILE_FORMAT_KME60 - Input and output file format.
+
+***
+
 ### LOG\_FILE\_FORMAT\_MATLAB
 
 > **LOG\_FILE\_FORMAT\_MATLAB**: `102`

package/doc_md/models/enumerations/LogLevel.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 

package/doc_md/models/enumerations/LogReplayState.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 
@@ -14,12 +14,16 @@ Possible log replay states.
 
 > **LOG\_REPLAY\_STATE\_STARTED**: `1`
 
+LOG_REPLAY_STATE_STARTED - The log replay is in started state.
+
 ***
 
 ### LOG\_REPLAY\_STATE\_STOPPED
 
 > **LOG\_REPLAY\_STATE\_STOPPED**: `2`
 
+LOG_REPLAY_STATE_STOPPED - The log replay is in stopped state.
+
 ***
 
 ### LOG\_REPLAY\_STATE\_UNSPECIFIED

package/doc_md/models/enumerations/LoggerState.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 
@@ -14,18 +14,24 @@ Possible message or signal logger states.
 
 > **MESSAGE\_LOGGER\_STATE\_PRESTART**: `1`
 
+MESSAGE_LOGGER_STATE_PRESTART - The logger is in the pre-start state.
+
 ***
 
 ### MESSAGE\_LOGGER\_STATE\_STARTED
 
 > **MESSAGE\_LOGGER\_STATE\_STARTED**: `2`
 
+MESSAGE_LOGGER_STATE_STARTED - The logger is currently started.
+
 ***
 
 ### MESSAGE\_LOGGER\_STATE\_STOPPED
 
 > **MESSAGE\_LOGGER\_STATE\_STOPPED**: `3`
 
+MESSAGE_LOGGER_STATE_STOPPED - The logger is currently stopped.
+
 ***
 
 ### MESSAGE\_LOGGER\_STATE\_UNSPECIFIED

package/doc_md/models/enumerations/Separator.md

@@ -0,0 +1,37 @@
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
+
+***
+
+[Kvaser CanKing GUI Extensions SDK](../../modules.md) / [models](../README.md) / Separator
+
+# Enumeration: Separator
+
+Possible column separators for loggers.
+
+## Enumeration Members
+
+### SEPARATOR\_COMMA
+
+> **SEPARATOR\_COMMA**: `1`
+
+SEPARATOR_COMMA - Comma (,) separator
+
+***
+
+### SEPARATOR\_SEMICOLON
+
+> **SEPARATOR\_SEMICOLON**: `2`
+
+SEPARATOR_SEMICOLON - Semicolon (;) separator
+
+***
+
+### SEPARATOR\_UNSPECIFIED
+
+> **SEPARATOR\_UNSPECIFIED**: `0`
+
+***
+
+### UNRECOGNIZED
+
+> **UNRECOGNIZED**: `-1`

package/doc_md/models/enumerations/SignalEncoding.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 
@@ -14,12 +14,16 @@ Possible signal encodings. The value must match the kvadblib value.
 
 > **SIGNAL\_ENCODING\_INTEL**: `0`
 
+SIGNAL_ENCODING_INTEL - Intel / little endian encoding
+
 ***
 
 ### SIGNAL\_ENCODING\_MOTOROLA
 
 > **SIGNAL\_ENCODING\_MOTOROLA**: `1`
 
+SIGNAL_ENCODING_MOTOROLA - Motorola / big endian encoding
+
 ***
 
 ### UNRECOGNIZED

package/doc_md/models/enumerations/SignalType.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 

package/doc_md/models/enumerations/SignalValueTriggerOperator.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 
@@ -14,54 +14,72 @@ Possible signal value trigger operators.
 
 > **SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_CHANGE\_FROM**: `8`
 
+SIGNAL_VALUE_TRIGGER_OPERATOR_CHANGE_FROM - Change from
+
 ***
 
 ### SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_CHANGE\_TO
 
 > **SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_CHANGE\_TO**: `7`
 
+SIGNAL_VALUE_TRIGGER_OPERATOR_CHANGE_TO - Change to
+
 ***
 
 ### SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_EQUAL\_TO
 
 > **SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_EQUAL\_TO**: `1`
 
+SIGNAL_VALUE_TRIGGER_OPERATOR_EQUAL_TO - Equal to
+
 ***
 
 ### SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_GREATER\_THAN
 
 > **SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_GREATER\_THAN**: `6`
 
+SIGNAL_VALUE_TRIGGER_OPERATOR_GREATER_THAN - Greater than
+
 ***
 
 ### SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_GREATER\_THAN\_OR\_EQUAL
 
 > **SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_GREATER\_THAN\_OR\_EQUAL**: `5`
 
+SIGNAL_VALUE_TRIGGER_OPERATOR_GREATER_THAN_OR_EQUAL - Greater than or equal to
+
 ***
 
 ### SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_LESS\_THAN
 
 > **SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_LESS\_THAN**: `3`
 
+SIGNAL_VALUE_TRIGGER_OPERATOR_LESS_THAN - Less than
+
 ***
 
 ### SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_LESS\_THAN\_OR\_EQUAL
 
 > **SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_LESS\_THAN\_OR\_EQUAL**: `4`
 
+SIGNAL_VALUE_TRIGGER_OPERATOR_LESS_THAN_OR_EQUAL - Less than or equal to
+
 ***
 
 ### SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_NOT\_EQUAL\_TO
 
 > **SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_NOT\_EQUAL\_TO**: `2`
 
+SIGNAL_VALUE_TRIGGER_OPERATOR_NOT_EQUAL_TO - Not equal to
+
 ***
 
 ### SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_ON\_CHANGE
 
 > **SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_ON\_CHANGE**: `9`
 
+SIGNAL_VALUE_TRIGGER_OPERATOR_ON_CHANGE - On change
+
 ***
 
 ### SIGNAL\_VALUE\_TRIGGER\_OPERATOR\_UNSPECIFIED

package/doc_md/models/enumerations/StatusLevel.md

@@ -1,4 +1,4 @@
-[**Kvaser CanKing GUI Extensions SDK v7.3.0**](../../README.md)
+[**Kvaser CanKing GUI Extensions SDK v7.4.0**](../../README.md)
 
 ***
 
@@ -14,6 +14,8 @@ Possible CAN frame flags. The flag value must match the canlib flag value.
 
 > **STATUS\_LEVEL\_ERROR**: `3`
 
+STATUS_LEVEL_ERROR - Status is error.
+
 ***
 
 ### STATUS\_LEVEL\_NONE
@@ -26,12 +28,16 @@ Possible CAN frame flags. The flag value must match the canlib flag value.
 
 > **STATUS\_LEVEL\_OK**: `1`
 
+STATUS_LEVEL_OK - Status is OK.
+
 ***
 
 ### STATUS\_LEVEL\_WARNING
 
 > **STATUS\_LEVEL\_WARNING**: `2`
 
+STATUS_LEVEL_WARNING - Status is warning.
+
 ***
 
 ### UNRECOGNIZED