@esri/solutions-components 0.8.37 → 0.8.39

package/dist/cjs/pciUtils-a238f3a1.js

@@ -1,847 +0,0 @@
-/*!
- * Copyright 2022 Esri
- * Licensed under the Apache License, Version 2.0
- * http://www.apache.org/licenses/LICENSE-2.0
- */
-'use strict';
-
-/** @license
- * Copyright 2022 Esri
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- *    http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-/**
- * Effect of the distresses on ride quality.
- *
- * L - Low. Individual bumps or settlements, or both, cause the vehicle to bounce slightly,
- * but create little discomfort.
- *
- * M - Medium. Individual bumps or settlements, or both, cause the vehicle to bounce significantly,
- * creating some discomfort.
- *
- * H - High. Individual bumps or settlements, or both, cause the vehicle to bounce excessively,
- * creating substantial discomfort, safety hazard, or high potential vehicle damage.
- *
- * @returns Promise resolving when function is done
- *
- */
-exports.ESeverity = void 0;
-(function (ESeverity) {
-    ESeverity["H"] = "H";
-    ESeverity["M"] = "M";
-    ESeverity["L"] = "L";
-})(exports.ESeverity || (exports.ESeverity = {}));
-/**
- * Type of distress as defined by ASTM standard
- *
- */
-exports.EDistressType = void 0;
-(function (EDistressType) {
-    EDistressType[EDistressType["ALLIGATOR_CRACKING"] = 1] = "ALLIGATOR_CRACKING";
-    EDistressType[EDistressType["BLEEDING"] = 2] = "BLEEDING";
-    EDistressType[EDistressType["BLOCK_CRACKING"] = 3] = "BLOCK_CRACKING";
-    EDistressType[EDistressType["BUMPS_SAGS"] = 4] = "BUMPS_SAGS";
-    EDistressType[EDistressType["CORRUGATION"] = 5] = "CORRUGATION";
-    EDistressType[EDistressType["DEPRESSION"] = 6] = "DEPRESSION";
-    EDistressType[EDistressType["EDGE_CRACKING"] = 7] = "EDGE_CRACKING";
-    EDistressType[EDistressType["REFLECTION_CRACKING"] = 8] = "REFLECTION_CRACKING";
-    EDistressType[EDistressType["LANE_SHOULDER_DROP_OFF"] = 9] = "LANE_SHOULDER_DROP_OFF";
-    EDistressType[EDistressType["LONG_TRANS_CRACKING"] = 10] = "LONG_TRANS_CRACKING";
-    EDistressType[EDistressType["PATCHING_UTIL_CUT_PATCHING"] = 11] = "PATCHING_UTIL_CUT_PATCHING";
-    EDistressType[EDistressType["POLISHED_AGGREGATE"] = 12] = "POLISHED_AGGREGATE";
-    EDistressType[EDistressType["POTHOLES"] = 13] = "POTHOLES";
-    EDistressType[EDistressType["RAILROAD_CROSSING"] = 14] = "RAILROAD_CROSSING";
-    EDistressType[EDistressType["RUTTING"] = 15] = "RUTTING";
-    EDistressType[EDistressType["SHOVING"] = 16] = "SHOVING";
-    EDistressType[EDistressType["SLIPPAGE_CRACKING"] = 17] = "SLIPPAGE_CRACKING";
-    EDistressType[EDistressType["SWELL"] = 18] = "SWELL";
-    EDistressType[EDistressType["RAVELING"] = 19] = "RAVELING";
-    EDistressType[EDistressType["WEATHERING"] = 20] = "WEATHERING";
-})(exports.EDistressType || (exports.EDistressType = {}));
-/**
- * Calculate the deduct value for the given distress.
- *
- * @param type expects 1-19 as a string
- * @param severity expects "H" | "M" | "L"
- * @param density the calculated percent density ralative to the total sample area
- * @param showDebugging used to control debugging messages to show the various
- * calculations a required steps along the way.
- * The main reason this is optional is that it provides no value when used within
- * Survey123 as we have nowhere to see the messages and I wasn't sure if writing to a
- * console in that context could have any negative side effects.
- *
- * @returns pipe delimited string: type|severity|roundedDeductValue|density
- */
-function calculateDeductValue(type, severity, density, showDebugging = false) {
-    // When called from survey123 we will get the args as strings
-    // not sure if they could be numbers so a little extra conversion to make sure with the density
-    const _type = parseInt(type);
-    const _severity = exports.ESeverity[severity];
-    const _density = parseFloat(density.toString());
-    // When called from survey123 all distress types and severities will be passed in
-    // We only need to calculate the deduct value if we have a valid density
-    if (Number.isNaN(_density) || _density === 0) {
-        return "";
-    }
-    const _showDebugging = showDebugging === true || showDebugging.toString().toLowerCase() === "true";
-    let calc;
-    switch (_type) {
-        case exports.EDistressType.ALLIGATOR_CRACKING:
-            calc = _calcAlligator;
-            break;
-        case exports.EDistressType.BLEEDING:
-            calc = _calcBleeding;
-            break;
-        case exports.EDistressType.BLOCK_CRACKING:
-            calc = _calcBlockCracking;
-            break;
-        case exports.EDistressType.BUMPS_SAGS:
-            calc = _calcBumpsSags;
-            break;
-        case exports.EDistressType.CORRUGATION:
-            calc = _calcCorrugation;
-            break;
-        case exports.EDistressType.DEPRESSION:
-            calc = _calcDepression;
-            break;
-        case exports.EDistressType.EDGE_CRACKING:
-            calc = _calcEdgeCracking;
-            break;
-        case exports.EDistressType.REFLECTION_CRACKING:
-            calc = _calcReflectionCracking;
-            break;
-        case exports.EDistressType.LANE_SHOULDER_DROP_OFF:
-            calc = _calcLaneShoulderDropOff;
-            break;
-        case exports.EDistressType.LONG_TRANS_CRACKING:
-            calc = _calcLongTransCracking;
-            break;
-        case exports.EDistressType.PATCHING_UTIL_CUT_PATCHING:
-            calc = _calcPatchingUtilCutPatching;
-            break;
-        case exports.EDistressType.POLISHED_AGGREGATE:
-            calc = _calcPolishedAggregate;
-            break;
-        case exports.EDistressType.POTHOLES:
-            calc = _calcPotholes;
-            break;
-        case exports.EDistressType.RAILROAD_CROSSING:
-            calc = _calcRailroadCrossing;
-            break;
-        case exports.EDistressType.RUTTING:
-            calc = _calcRutting;
-            break;
-        case exports.EDistressType.SHOVING:
-            calc = _calcShoving;
-            break;
-        case exports.EDistressType.SLIPPAGE_CRACKING:
-            calc = _calcSlippageCracking;
-            break;
-        case exports.EDistressType.SWELL:
-            calc = _calcSwell;
-            break;
-        case exports.EDistressType.RAVELING:
-            calc = _calcRaveling;
-            break;
-        case exports.EDistressType.WEATHERING:
-            calc = _calcWeathering;
-            break;
-    }
-    const dv = calc(_severity, Math.log10(_density));
-    const roundedDV = _round(dv);
-    const formattedDV = `${type}|${severity}|${roundedDV}|${_density}`;
-    if (_showDebugging) {
-        console.log(`Deduct value: ${dv}`);
-        console.log(`Rounded deduct value: ${roundedDV}`);
-        console.log(`Formatted devduct value (type|severity|roundedDV|density): ${formattedDV}`);
-    }
-    return formattedDV;
-}
-/**
- * Calculate the pavement condition index (PCI)
- *
- * @param deductValues string of comma delimited values
- * @param showDebugging used to control debugging messages to show the various
- * calculations a required steps along the way.
- * The main reason this is optional is that it provides no value when used within
- * Survey123 as we have nowhere to see the messages and I wasn't sure if writing to a
- * console in that context could have any negative side effects.
- *
- * @returns the calculated PCI
- */
-function calculatePCI(deductValues, showDebugging = false) {
-    // When called from survey123 we will get the args as strings
-    // When comparing multi-severities calculatePCI will be called multiple times
-    // When called from _evaluateMultiSeverity we will just recieve a comma delimited string
-    // When its just comma delimited we don't need to re-evaluate the multiple severities
-    let _deductValues = deductValues.indexOf("|") > -1 ?
-        _evaluateMultiSeverity(deductValues, showDebugging) :
-        deductValues.split(",").map(dv => parseFloat(dv));
-    const _showDebugging = showDebugging === true || showDebugging.toString().toLowerCase() === "true";
-    let pci = 0;
-    // filter out non-numbers
-    _deductValues = _deductValues.filter(dv => Math.abs(dv) > 0);
-    if (_deductValues.length > 0) {
-        const maxCDV = _getMaxCDV(_deductValues, _showDebugging);
-        pci = 100 - _round(maxCDV);
-    }
-    return pci;
-}
-/**
- * Determine if corrections are required when we have multiple severities of a single distress type.
- *
- * @param deductValues string of comma delimited values e.g. "1|L|10|0.52,1|H|7|0.58"
- * @param showDebugging used to control debugging messages to show the various
- * calculations a required steps along the way.
- *
- * @returns an object that will contain any corrections for the current distress type
- */
-function _evaluateMultiSeverity(deductValues, showDebugging) {
-    const updates = {};
-    const _dvObject = _parseDeductValues(deductValues);
-    const multiSeverityKeys = Object.keys(_dvObject).filter(k => Object.keys(_dvObject[k]).length > 1);
-    if (multiSeverityKeys.length > 0) {
-        multiSeverityKeys.forEach(k => {
-            let hDeductValue;
-            let mDeductValue;
-            let lDeductValue;
-            let hDensity;
-            let mDensity;
-            let lDensity;
-            // need to know if 2 or 3 severity case
-            Object.keys(_dvObject[k]).forEach(_k => {
-                if (_k === "H") {
-                    hDeductValue = _dvObject[k][_k].deductValue;
-                    hDensity = _dvObject[k][_k].density;
-                }
-                else if (_k === "M") {
-                    mDeductValue = _dvObject[k][_k].deductValue;
-                    mDensity = _dvObject[k][_k].density;
-                }
-                else {
-                    lDeductValue = _dvObject[k][_k].deductValue;
-                    lDensity = _dvObject[k][_k].density;
-                }
-            });
-            const func = (hDensity && mDensity && lDensity) ?
-                _getThreeSeverityCaseUpdates : _getTwoSeverityCaseUpdates;
-            const update = func(k, hDeductValue, mDeductValue, lDeductValue, hDensity, mDensity, lDensity, showDebugging);
-            if (update) {
-                updates[k] = update;
-                if (showDebugging) {
-                    console.log("updates");
-                    console.log(updates);
-                }
-            }
-        });
-    }
-    return _getFinalDeductValues(deductValues, updates);
-}
-/**
- * Determine if corrections are required when we have 3 severities of a single distress type.
- *
- * @param type the distress type 1-19 as a string
- * @param hDeductValue high severity deduct value
- * @param mDeductValue med severity deduct value
- * @param lDeductValue low severity deduct value
- * @param hDensity high severity density
- * @param mDensity med severity density
- * @param lDensity low severity density
- * @param showDebugging used to control debugging messages to show the various
- * calculations a required steps along the way.
- *
- * @returns undefined or an object that will contain any corrections for the current distress type
- */
-function _getThreeSeverityCaseUpdates(type, hDeductValue, mDeductValue, lDeductValue, hDensity, mDensity, lDensity, showDebugging) {
-    const pci1 = calculatePCI(`${hDeductValue},${mDeductValue},${lDeductValue}`, true);
-    if (showDebugging) {
-        console.log("pci1");
-        console.log(pci1);
-    }
-    const lm = lDensity + mDensity;
-    const lmPCI2 = _getPCI2(type, "M", lm.toString(), hDeductValue, showDebugging);
-    const mh = mDensity + hDensity;
-    const mhPCI2 = _getPCI2(type, "H", mh.toString(), lDeductValue, showDebugging);
-    const lh = lDensity + hDensity;
-    const lhPCI2 = _getPCI2(type, "H", lh.toString(), mDeductValue, showDebugging);
-    const lmh = lDensity + mDensity + hDensity;
-    const lmhPCI2 = _getPCI2(type, "H", lmh.toString(), 0, showDebugging);
-    if (showDebugging) {
-        console.log("low med pci2");
-        console.log(lmPCI2.pci);
-        console.log("med high pci2");
-        console.log(mhPCI2.pci);
-        console.log("low high pci2");
-        console.log(lhPCI2.pci);
-        console.log("low med high pci2");
-        console.log(lmhPCI2.pci);
-    }
-    const pcis = [lmPCI2, mhPCI2, lhPCI2, lmhPCI2];
-    const highest = pcis.reduce((prev, cur) => {
-        return cur.pci > pci1 && (!prev || cur.pci > prev.pci) ? cur : prev;
-    }, undefined);
-    return highest ? highest.dv : undefined;
-}
-/**
- * Determine if corrections are required when we have 2 severities of a single distress type.
- *
- * @param type the distress type 1-19 as a string
- * @param hDeductValue high severity deduct value
- * @param mDeductValue med severity deduct value
- * @param lDeductValue low severity deduct value
- * @param hDensity high severity density
- * @param mDensity med severity density
- * @param lDensity low severity density
- * @param showDebugging used to control debugging messages to show the various
- * calculations a required steps along the way.
- *
- * @returns undefined or an object that will contain any corrections for the current distress type
- */
-function _getTwoSeverityCaseUpdates(type, hDeductValue, mDeductValue, lDeductValue, hDensity, mDensity, lDensity, showDebugging) {
-    const hDV = hDeductValue || mDeductValue;
-    const lDV = lDeductValue || mDeductValue;
-    const pci1 = calculatePCI(`${hDV},${lDV}`, true);
-    if (showDebugging) {
-        console.log("pci1");
-        console.log(pci1);
-    }
-    const hDen = hDensity || mDensity;
-    const lDen = lDensity || mDensity;
-    const sumDen = hDen + lDen;
-    const highestSeverity = hDen === hDensity ? "H" : "M";
-    const pci2 = _getPCI2(type, highestSeverity, sumDen.toString(), 0, showDebugging);
-    if (showDebugging) {
-        console.log("pci2");
-        console.log(pci2.pci);
-    }
-    return pci2.pci > pci1 ? pci2.dv : undefined;
-}
-/**
- * Used to test for highest PCI when we have multiple severity cases for a single distress type.
- *
- * @param type the distress type 1-19 as a string
- * @param severity expects "H" | "M" | "L"
- * @param density the calculated percent density ralative to the total sample area
- * @param secondDeductValue optional deduct value will be 0 for all 2 severity cases and will be a non 0 number for 3 severity cases
- * @param showDebugging used to control debugging messages to show the various
- * calculations a required steps along the way.
- *
- * @returns ICorrection that contains the new PCI as well as the deduct values that should be used for corrections
- */
-function _getPCI2(type, severity, density, secondDeductValue, showDebugging) {
-    const deductValue = calculateDeductValue(type, severity, density);
-    const splitVal = deductValue.split("|");
-    const newDV = parseFloat(splitVal[2]);
-    return {
-        pci: calculatePCI(`${splitVal[2]},${secondDeductValue}`, showDebugging),
-        dv: secondDeductValue ? [newDV, secondDeductValue] : [newDV]
-    };
-}
-/**
- * Parse the deduct value string into individual values for type, severity, deduct value, and density
- *
- * @param deductValues string of comma delimited values for type, severity, deduct value, and density
- *
- * @returns an object with the parsed values
- */
-function _parseDeductValues(deductValues) {
-    return deductValues.split(",").reduce((prev, cur) => {
-        const splitVal = cur.split("|");
-        const type = splitVal[0];
-        const severity = splitVal[1];
-        const deductValue = parseFloat(splitVal[2]);
-        const density = parseFloat(splitVal[3]);
-        if (!prev[type]) {
-            prev[type] = {};
-        }
-        prev[type][severity] = {
-            deductValue,
-            density
-        };
-        return prev;
-    }, {});
-}
-/**
- * Replace any deduct values for the given distress types when it is determined that corrections
- * are required for a multi-severity case
- *
- * @param deductValues string of comma delimited values for type, severity, deduct value, and density
- * @param updates will contain the new corrected deduct value(s) that should be substituted for the original deduct value
- *
- * @returns an object with the parsed and updated deduct values to use for final PCI calculation
- */
-function _getFinalDeductValues(deductValues, updates) {
-    const skipAdditionalTypes = [];
-    return deductValues.split(",").reduce((prev, cur) => {
-        //0: type, 1: severity, 2: deductValue, 3: density
-        const splitVal = cur.split("|");
-        const type = splitVal[0];
-        const deductValue = parseFloat(splitVal[2]);
-        if (Object.keys(updates).length > 0 && updates[type]) {
-            skipAdditionalTypes.push(type);
-            prev.push(...updates[type]);
-            delete (updates[type]);
-        }
-        else if (skipAdditionalTypes.indexOf(type) < 0) {
-            prev.push(deductValue);
-        }
-        return prev;
-    }, []);
-}
-/**
- * Executes the polynomial equation using the provided values and density.
- * In the ASTM standard this is the step represented by finding the values
- * on the plotted graphs.
- *
- * @returns the calculated deduct value
- */
-function _calc(density, vals) {
-    return vals.reduce((prev, cur, i) => {
-        return prev += i === 0 ? cur :
-            i === 1 ? (cur * density) :
-                (cur * Math.pow(density, i));
-    }, 0);
-}
-/**
- * Round to the nerest decimal in the 10ths place
- */
-function _round(v) {
-    return Math.round(v * 10) / 10;
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcAlligator(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [30.71, 29.22, 9.407, -6.981, -2.158, 3.047, -0.6578] :
-        severity === exports.ESeverity.M ? [21.62, 21.32, 5.194, -1.343, 0.2341] :
-            [11.31, 16.05, 7.572, -1.471];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcBleeding(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [5.343, 6.927, 7.926, 4.265, -0.7582] :
-        severity === exports.ESeverity.M ? [2.38, 5.483, 4.128, 0.8366, 0.03659, 0.1052] :
-            [0.01391, 0.5079, 1.576, 1.191, 0.1329, 0.03823];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcBlockCracking(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [7.926, 11.93, 8.826, 3.432, -1.382] :
-        severity === exports.ESeverity.M ? [2.587, 9.142, 6.647, -0.455, -0.2439, 0.1107] :
-            [0.646, 4.002, 4.2, 0.4987, -0.06269];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcBumpsSags(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [52.77, 38.07, 8.964, -0.4148, -1.589, 2.478] :
-        severity === exports.ESeverity.M ? [24.66, 27.86, 15.73, 3.295, -5.27, 5.921, 7.959] :
-            [8.768, 13.79, 7.064, 7.455, 6.041, -1.739, -1.371];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcCorrugation(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [34.21, 21.59, 1.863, 6.1410, -0.687, -1.885, 0.4916] :
-        severity === exports.ESeverity.M ? [15.78, 19.69, 6.276, -2.124, 0.5868, 0.06045] :
-            [2.173, 5.609, 5.976, -0.7348, -0.2172, 1.494, -0.5659];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcDepression(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [17.84, 5.904, 9.406, 18.28, -2.753, -7.798, 2.402] :
-        severity === exports.ESeverity.M ? [8.471, 3.171, 10.25, 12.2, -0.9687, -4.601, 1.079] :
-            [4.836, -0.7572, 4.786, 12.39, 1.233, -4.871, 0.9749];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcEdgeCracking(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [14.99, 13.5, 10.62, 5.15, -1.792, -2.826] :
-        severity === exports.ESeverity.M ? [9.177, 10.26, 5.704, -0.6812, -0.8588, 0.2123] :
-            [3.049, 4.802, 4.058, -0.3556, -1.55, 1.02];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcReflectionCracking(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [14.99, 17.21, 27.63, 31.13, -20.94, -18.82, 9.985] :
-        severity === exports.ESeverity.M ? [9.9193, 10.88, 8.073, 14.8, -3.792, -9.583, 3.651] :
-            [2.356, 6.664, 3.717, -1.393, 1.94, 1.785, -0.9707];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcLaneShoulderDropOff(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [7.549, 6.907, 7.284, 9.304, 2.064] :
-        severity === exports.ESeverity.M ? [4.02, 1.744, 14.36, 15.92, -40.22, 23.6] :
-            [2.004, 1.065, 9.706, 11.75, -27.52, 15.04];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcLongTransCracking(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [19.56, 24.06, 12.12, 9.336, 1.532, -4.396] :
-        severity === exports.ESeverity.M ? [9.751, 15.53, 4.719, 1.369, 1.206, -1.164] :
-            [2.347, 9.074, 8.424, -1.338, -1.873, 1.144];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcPatchingUtilCutPatching(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [20.15, 16.55, 5.415, 10.77, 3.257, -4.502] :
-        severity === exports.ESeverity.M ? [10.28, 12.71, 6.174, 1.928, 0.6923, -0.4673] :
-            [2.523, 6.892, 5.702, 2.407, 0.2185, -0.8722];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcPolishedAggregate(severity, density) {
-    const vals = severity === "H" || severity === "M" || severity === "L" ?
-        [3.417, -26.82, 71.15, -76.22, 38.52, -6.904] : [];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcPotholes(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [110.7, 60.66, 2.378, -2.664] :
-        severity === exports.ESeverity.M ? [90.47, 60.41, -0.1123, -4.746] :
-            [58.19, 40.53, 2.884, -1.443, 0.1195];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcRailroadCrossing(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [20, 38.64, -62.82, 193.6, -162.7, 41.22] :
-        severity === exports.ESeverity.M ? [6.994, 23.47, -52.3, 167.3, -143.6, 37.64] :
-            [1.998, -0.7488, 13.8, -0.7917, -1.981];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcRutting(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [27.61, 25.19, 8.557, 1.65, -2.2030] :
-        severity === exports.ESeverity.M ? [18.47, 20.77, 6.617, -1.13, -2.286] :
-            [8.833, 14.84, 3.129, 0.1451, 2.438, -1.279];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcShoving(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [18.7, 20.17, 10.3, 4.694, 1.331, -2.61] :
-        severity === exports.ESeverity.M ? [10.39, 14.78, 5.488, 4.001, 3.23, -2.387] :
-            [4.002, 10.66, 6.332, -0.5226, -0.1923];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcSlippageCracking(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [19.73, 32.21, 25.87, -2.871, -10.55, 1.496, 0.7393] :
-        severity === exports.ESeverity.M ? [11.38, 18.55, 18.38, 1.628, -7.596, 0.5841, 0.5946] :
-            [5.144, 12.95, 11.95, -0.833, -2.995, 1.325, -0.2113];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcSwell(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [34, 16.84, -23.09, 41.17, -14.84] :
-        severity === exports.ESeverity.M ? [12, 15.67, 20.59, -28.33, 21, -5.508] :
-            [1.995, 11.9, -12.83, 16.74, -5.361];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcRaveling(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [16.77, 10.67, 5.758, 12.9, -0.0633, -5.659, 1.48] :
-        severity === exports.ESeverity.M ? [8.512, 5.106, 1.63, 3.469, 1.028, -1.211, 0.1938] :
-            [];
-    return _calc(density, vals);
-}
-/**
- * Execute the deduct value calculation for the distress type
- *
- * @param severity The severity of the distress type
- * @param density percent density of the distress type
- *
- * @returns the calculated deduct value
- */
-function _calcWeathering(severity, density) {
-    const vals = severity === exports.ESeverity.H ? [3.673, 3.349, 2.598, -1.233, 2.754, 2.434, -1.485] :
-        severity === exports.ESeverity.M ? [1.12, 0.9769, 0.93, -0.5955, 1.041, 1.111, -0.614] :
-            [-0.0386, -0.0736, 0.834, 1.63, -0.0287, -0.639, 0.1515];
-    return _calc(density, vals);
-}
-/**
- * Determine maximum Corrected Deduct Value (CDV) iteratively
- *
- * @param deductValues The calculated deduct values that will be used to determine max CDV
- * @param showDebugging used to optionally show debugging messages
- *
- * @returns the max CDV value
- */
-function _getMaxCDV(deductValues, showDebugging) {
-    let maxCDV;
-    // If none or only one individual deduct value is greater
-    // than two, the total value is used in place of the maximum CD
-    const valuesGreaterThan2 = deductValues.filter(deductValue => deductValue > 2);
-    if (valuesGreaterThan2.length <= 1) {
-        maxCDV = valuesGreaterThan2.reduce((prev, cur) => {
-            prev += cur;
-            return prev;
-        }, 0);
-        if (showDebugging) {
-            console.log("If none or only one individual deduct value is greater");
-            console.log("than two, the total value is used in place of the maximum CD");
-            console.log(`Max CDV: ${maxCDV}`);
-        }
-    }
-    else {
-        // sort in descending order (section 9.5.2 in ASTM doc)
-        const sortedDVs = deductValues.sort((a, b) => b - a);
-        // Determine the allowable number of deducts, m (section 9.5.3 in ASTM doc)
-        const highestDV = sortedDVs[0];
-        // m = allowable number of deducts including fractions (must be less than or equal to ten)
-        const m = 1 + (9 / 98) * (100 - highestDV);
-        if (showDebugging) {
-            console.log(`Deduct values sorted in descending order: ${sortedDVs}`);
-            console.log(`Highest deduct value: ${highestDV}`);
-            console.log(`Allowable number of deducts including fractions: ${m}`);
-        }
-        // TODO they mention (must be less than or equal to ten) but don't say what happens if its over
-        if (m <= 10) {
-            const vals = _reduceDeductValues(sortedDVs, m);
-            if (showDebugging) {
-                console.log(`Reduce deduct values to the m largest including the fractional part: ${vals}`);
-            }
-            // iteratively determined cdv values
-            const cdvs = _getCDVs(vals, showDebugging);
-            maxCDV = Math.max(...cdvs);
-            if (showDebugging) {
-                console.log(`Max CDV: ${maxCDV}`);
-            }
-        }
-        else {
-            if (showDebugging) {
-                console.log("Allowable number of deducts including fractions (must be less than or equal to ten)");
-            }
-        }
-    }
-    return maxCDV;
-}
-/**
- * Reduce deduct values to the m largest including the fractional part
- *
- * @param sortedDVs individual deduct values in descending order
- * @param m allowable number of deducts (9.5.3 in ASTM standard)
- *
- * @returns updated deduct values
- */
-function _reduceDeductValues(sortedDVs, m) {
-    const fractionalPart = m - Math.floor(m);
-    // If less than m deduct values are available, all of the deduct values are used
-    return sortedDVs.length < m ? sortedDVs :
-        sortedDVs.reduce((prev, cur, i) => {
-            if (i + 1 < m) {
-                prev.push(cur);
-            }
-            else if (fractionalPart > 0) {
-                prev.push(_round(cur * fractionalPart));
-            }
-            return prev;
-        }, []);
-}
-/**
- * Reduce the smallest individual deduct value greater to 2.0 and repeat
- *
- * @param vals the list of deduct values
- * @param showDebugging optionally show debugging messages
- *
- * @returns array of CDV values
- */
-function _getCDVs(vals, showDebugging) {
-    let len = vals.length;
-    const cdvs = [];
-    while (len >= 1) {
-        if (showDebugging) {
-            console.log(`vals: ${vals}`);
-        }
-        cdvs.push(_getCDV(vals, showDebugging));
-        len -= 1;
-        vals.splice(len, 1, 2);
-    }
-    return cdvs;
-}
-/**
- * Determine the total and max number deducts higher than two and calculate the CDV
- *
- * @param vals the list of deduct values
- * @param showDebugging optionally show debugging messages
- *
- * @returns the calculated CDV
- */
-function _getCDV(vals, showDebugging) {
-    // section 9.5.5.1 in ASTM doc
-    const totalDV = vals.reduce((prev, cur) => prev += cur, 0);
-    // section 9.5.5.2 in ASTM doc
-    // the number of deducts with a value greater than 2.0
-    const q = vals.reduce((prev, cur) => cur > 2 ? prev + 1 : prev, 0);
-    // section 9.5.5.3 in ASTM doc
-    return _calcCDV(totalDV, q, showDebugging);
-}
-/**
- * Determine the total and max number deducts higher than two and calculate the CDV
- *
- * @param total the sum of all deduct values
- * @param q the number of deducts with a value greater than 2.0
- * @param showDebugging optionally show debugging messages
- *
- * @returns the calculated CDV
- */
-function _calcCDV(total, q, showDebugging) {
-    // Determine the CDV from total deduct value and q
-    const vals2 = {
-        7: [-9.482, 0.6045, 0.0003563, -5.448e-06],
-        6: [-8.165, 0.5724, 0.0004266, -4.254e-06],
-        5: [-7.932, 0.6091, 0.0003464, -4.265e-06],
-        4: [-6.78, 0.6301, 0.0007376, -6.357e-06],
-        3: [-5.015, 0.7546, -0.00043, -3.075e-06],
-        2: [-1.668, 0.7992, -0.0003013, -5.214e-06],
-        1: [1.651e-15, 1, -4.249e-18, 1.149e-19]
-    };
-    const cdv = _calc(total, vals2[q >= 7 ? 7 : q]);
-    if (showDebugging) {
-        console.log(`totalDV: ${total}`);
-        console.log(`q: ${q}`);
-        console.log(`CDV: ${cdv}`);
-    }
-    return cdv;
-}
-
-exports.calculateDeductValue = calculateDeductValue;
-exports.calculatePCI = calculatePCI;