@camera.ui/camera-ui-eufy 2.0.3 → 2.1.0

This diff represents the content of publicly available package versions that have been released to one of the supported registries. The information contained in this diff is provided for informational purposes only and reflects changes between package versions as they appear in their respective public registries.
package/CHANGELOG.md CHANGED
@@ -1,3 +1,37 @@
1
+ ## [2.1.0]
2
+
3
+ - **Battery cameras and doorbells are recognized when you add them.** camera.ui then sets up a battery camera so it can sleep. Needs camera.ui 2.4.0.
4
+ - **The live view freezes less often.** Frames that arrive late, in a burst or cut between two network packets no longer stop the picture until the next full frame. After a frame is lost for good, the picture holds until the next full frame instead of showing grey smears.
5
+ - **A camera that went silent is noticed and reconnected**, so the live view no longer stays stuck on it. A camera on a power supply that accepts a live view but sends no picture gets a new connection after a few seconds instead of 20.
6
+ - **Closing the live view of a camera without a HomeBase stops its stream.** The camera kept streaming, and a light that follows the stream stayed on.
7
+ - **Cameras behind a HomeBase 3 keep streaming.** After a while every new live view failed until the connection was rebuilt.
8
+ - **Detections and doorbell presses come in more reliably.** The plugin signs up for Eufy notifications the way the Eufy app does. When that fails at startup it tries again, until now nothing came in until a restart. With debug logging on, every Eufy notification shows up in the log.
9
+ - **Cameras behind a HomeBase 2 show the picture of their latest event**, also when the event arrives before its picture. Some pictures that stayed empty show up now too.
10
+ - **Cameras behind a HomeBase S1 Pro (T9000) show a live view**, one camera at a time and without sound, on a 64-bit system. The siren of more cameras behind it can be triggered, among them the SoloCam S220 and L20, eufyCam 2C, Video Doorbell Dual and Indoor Cam. These cameras no longer offer RTSP, which never worked there.
11
+ - **The Video Doorbell C31 shows a live view**, without sound and on a 64-bit system.
12
+ - **PoE cameras behind their recorder show a live view with sound**, among them the PoE S4 and E40, on a 64-bit system.
13
+ - **More devices work as in the Eufy app.** The siren of a HomeBase 3 can be triggered, the PoE S4 behind its recorder shows up as a camera, and a Video Doorbell Dual behind a HomeBase shows the split picture instead of a small inset. The Baby Monitor E21 can pan and tilt, and the spotlight of an eufyCam E330 Pro can be switched.
14
+ - **More doorbells ring in camera.ui**, also when their name does not say doorbell. Among them the Video Doorbell T8210C and Video Doorbell Dual T8213, the Wired Doorbell, Wired Doorbell 2K Pro and Wired Doorbell Dual, and the Battery Doorbell, Battery Doorbell Slim and Battery Doorbell 2E.
15
+ - **An Indoor Cam Pan & Tilt behind a HomeBase can be turned on and off**, and its switch shows the right state. Before, "on" could turn it off. An Indoor Cam S350 behind a HomeBase can be turned on and off too.
16
+ - **The plugin stays logged in to Eufy when it moves to a worker and back**, instead of asking for a new verification code.
17
+ - **Some cameras no longer log the same warning about their motion sensitivity or AI detection every ten minutes.**
18
+ - **Stopping an alarm in the Eufy app ends it in camera.ui right away.** The guard mode kept showing the alarm for up to 15 minutes.
19
+ - **No new verification code every 30 minutes.** When Eufy asked for a verification code, the plugin tried to log in again every 30 minutes, and Eufy sent a new code each time.
20
+ - **The SoloCam S220 no longer shows pan and tilt controls** it does not have.
21
+ - **The Smoke Alarm E10 shows up as a smoke sensor** instead of a camera.
22
+ - **The guard mode of an Indoor Cam T8410C can be changed.** Every change failed before.
23
+ - **Changing the country in the plugin settings logs in again.** The plugin kept the session of the old country, a verification code may be asked for.
24
+ - **The Video Smart Lock S330 behind a HomeBase 3 locks and unlocks.** It refused every command before. When the lock does not turn, camera.ui shows its real state again after a few seconds.
25
+ - Bump camera.ui engine and SDK
26
+
27
+ ## [2.0.4]
28
+
29
+ - Detections that come in as Eufy notifications reach their camera. Many of them were dropped because the notification could not be assigned to a device
30
+ - Cameras connect more reliably when the direct connection has to pass a router
31
+ - The Wall Light Cam S100 no longer cuts its live view about once a minute
32
+ - The light of the Floodlight Cam T8423 can be switched
33
+ - Bump camera.ui engine and SDK
34
+
1
35
  ## [2.0.3]
2
36
 
3
37
  - The HomeBase T9000 is recognized as a HomeBase. It showed up as a camera before, without guard mode, and the cameras behind it did not find their station
package/bundle.zip CHANGED
Binary file
package/package.json CHANGED
@@ -1,7 +1,7 @@
1
1
  {
2
2
  "displayName": "Eufy",
3
3
  "name": "@camera.ui/camera-ui-eufy",
4
- "version": "2.0.3",
4
+ "version": "2.1.0",
5
5
  "description": "Integrates Eufy cameras, doorbells, HomeBases and sensors into camera.ui, with device discovery, live streaming, two-way audio, detection events, camera controls and adoptable Eufy sensors.",
6
6
  "author": "seydx (https://github.com/cameraui/plugins)",
7
7
  "main": "./dist/index.js",
@@ -20,11 +20,14 @@
20
20
  "publish:latest": "npm i --save --force && npm run bundle && cui publish --latest",
21
21
  "update": "updates -M npm,pypi,go,cargo,docker,make --update ./"
22
22
  },
23
+ "dependencies": {
24
+ "node-datachannel": "^0.33.4"
25
+ },
23
26
  "bugs": {
24
27
  "url": "https://github.com/cameraui/plugins/issues"
25
28
  },
26
29
  "engines": {
27
- "camera.ui": ">=2.2.5",
30
+ "camera.ui": ">=2.4.0",
28
31
  "node": ">=24.5.0"
29
32
  },
30
33
  "os": [],
@@ -44,7 +47,7 @@
44
47
  "directory": "camera-ui-eufy"
45
48
  },
46
49
  "allowScripts": {
47
- "node-av@6.2.0-beta.5": true
50
+ "node-av@6.2.0-beta.32": true
48
51
  },
49
52
  "cameraui": {
50
53
  "protocolLevel": 2