tecscde 0.6.0

data/lib/tecscde/tecs_model/tm_e_port.rb

@@ -0,0 +1,126 @@
+#
+# TECSCDE - TECS Component Diagram Editor
+#
+# Copyright (C) 2014-2019 by TOPPERS Project
+#
+#  The above copyright holders grant permission gratis to use,
+#  duplicate, modify, or redistribute (hereafter called use) this
+#  software (including the one made by modifying this software),
+#  provided that the following four conditions (1) through (4) are
+#  satisfied.
+#
+#  (1) When this software is used in the form of source code, the above
+#      copyright notice, this use conditions, and the disclaimer shown
+#      below must be retained in the source code without modification.
+#
+#  (2) When this software is redistributed in the forms usable for the
+#      development of other software, such as in library form, the above
+#      copyright notice, this use conditions, and the disclaimer shown
+#      below must be shown without modification in the document provided
+#      with the redistributed software, such as the user manual.
+#
+#  (3) When this software is redistributed in the forms unusable for the
+#      development of other software, such as the case when the software
+#      is embedded in a piece of equipment, either of the following two
+#      conditions must be satisfied:
+#
+#    (a) The above copyright notice, this use conditions, and the
+#        disclaimer shown below must be shown without modification in
+#        the document provided with the redistributed software, such as
+#        the user manual.
+#
+#    (b) How the software is to be redistributed must be reported to the
+#        TOPPERS Project according to the procedure described
+#        separately.
+#
+#  (4) The above copyright holders and the TOPPERS Project are exempt
+#      from responsibility for any type of damage directly or indirectly
+#      caused from the use of this software and are indemnified by any
+#      users or end users of this software from any and all causes of
+#      action whatsoever.
+#
+#  THIS SOFTWARE IS PROVIDED "AS IS." THE ABOVE COPYRIGHT HOLDERS AND
+#  THE TOPPERS PROJECT DISCLAIM ANY EXPRESS OR IMPLIED WARRANTIES,
+#  INCLUDING, BUT NOT LIMITED TO, ITS APPLICABILITY TO A PARTICULAR
+#  PURPOSE. IN NO EVENT SHALL THE ABOVE COPYRIGHT HOLDERS AND THE
+#  TOPPERS PROJECT BE LIABLE FOR ANY TYPE OF DAMAGE DIRECTLY OR
+#  INDIRECTLY CAUSED FROM THE USE OF THIS SOFTWARE.
+#
+
+require "tecscde/tecs_model/tm_port"
+
+module TECSCDE
+  class TECSModel
+    # mikan ep array
+    class TmEPort < TECSCDE::TECSModel::TmPort
+      # @joins::[TmJoin]
+
+      def initialize(owner, port_def, subscript = nil)
+        @owner = owner
+        @port_def = port_def
+        @subscript = subscript
+
+        @joins = []
+        @edge_side, @offset = get_cell.get_new_eport_position(port_def)
+        modified {}
+      end
+
+      def moved(x_inc, y_inc)
+        @joins.each do |join|
+          join.moved_eport(x_inc, y_inc)
+        end
+      end
+
+      def add_join(join)
+        modified do
+          @joins << join
+        end
+      end
+
+      #=== TmEPort#include?
+      # TmEPort can have plural of joins.
+      # test if TmEPort has specified join.
+      def include?(join)
+        @joins.include?(join)
+      end
+
+      #=== TmEPort#get_joins
+      def get_joins
+        @joins
+      end
+
+      #=== TmEPort#delete
+      # this method is called from TmCell
+      def delete
+        modified do
+          joins = @joins.dup # in join.edelete delete_join is called and change @joins
+          joins.each(&:delete)
+        end
+      end
+
+      #=== TmEPort#delete_join
+      # this method is called from TmJoin
+      def delete_join(join)
+        modified do
+          @joins.delete(join)
+        end
+      end
+
+      #=== TmEPort#complete?
+      def complete?
+        !@joins.empty?
+      end
+
+      #=== TmEPort#clone_for_undo
+      def clone_for_undo
+        bu = clone
+        bu.copy_from(self)
+        bu
+      end
+
+      def setup_clone(joins)
+        @joins = joins.dup
+      end
+    end
+  end
+end

data/lib/tecscde/tecs_model/tm_e_port_array.rb

@@ -0,0 +1,78 @@
+#
+# TECSCDE - TECS Component Diagram Editor
+#
+# Copyright (C) 2014-2019 by TOPPERS Project
+#
+#  The above copyright holders grant permission gratis to use,
+#  duplicate, modify, or redistribute (hereafter called use) this
+#  software (including the one made by modifying this software),
+#  provided that the following four conditions (1) through (4) are
+#  satisfied.
+#
+#  (1) When this software is used in the form of source code, the above
+#      copyright notice, this use conditions, and the disclaimer shown
+#      below must be retained in the source code without modification.
+#
+#  (2) When this software is redistributed in the forms usable for the
+#      development of other software, such as in library form, the above
+#      copyright notice, this use conditions, and the disclaimer shown
+#      below must be shown without modification in the document provided
+#      with the redistributed software, such as the user manual.
+#
+#  (3) When this software is redistributed in the forms unusable for the
+#      development of other software, such as the case when the software
+#      is embedded in a piece of equipment, either of the following two
+#      conditions must be satisfied:
+#
+#    (a) The above copyright notice, this use conditions, and the
+#        disclaimer shown below must be shown without modification in
+#        the document provided with the redistributed software, such as
+#        the user manual.
+#
+#    (b) How the software is to be redistributed must be reported to the
+#        TOPPERS Project according to the procedure described
+#        separately.
+#
+#  (4) The above copyright holders and the TOPPERS Project are exempt
+#      from responsibility for any type of damage directly or indirectly
+#      caused from the use of this software and are indemnified by any
+#      users or end users of this software from any and all causes of
+#      action whatsoever.
+#
+#  THIS SOFTWARE IS PROVIDED "AS IS." THE ABOVE COPYRIGHT HOLDERS AND
+#  THE TOPPERS PROJECT DISCLAIM ANY EXPRESS OR IMPLIED WARRANTIES,
+#  INCLUDING, BUT NOT LIMITED TO, ITS APPLICABILITY TO A PARTICULAR
+#  PURPOSE. IN NO EVENT SHALL THE ABOVE COPYRIGHT HOLDERS AND THE
+#  TOPPERS PROJECT BE LIABLE FOR ANY TYPE OF DAMAGE DIRECTLY OR
+#  INDIRECTLY CAUSED FROM THE USE OF THIS SOFTWARE.
+#
+
+require "tecscde/tecs_model/tm_e_port"
+
+module TECSCDE
+  class TECSModel
+    class TmEPortArray < TECSCDE::TECSModel::TmPortArray
+      def initialize(cell, port_def)
+        # p "TmEPortArray port_def:#{port_def}"
+        @port_def = port_def
+        @owner = cell
+        if port_def.get_array_size == "[]"
+          @actual_size = 1
+        else
+          @actual_size = port_def.get_array_size
+        end
+
+        @ports = []
+        (0..(@actual_size - 1)).each do |subscript|
+          @ports << TECSCDE::TECSModel::TmEPort.new(self, port_def, subscript)
+        end
+        modified {}
+      end
+
+      #=== TmEPortArray#new_port
+      def new_port(subscript)
+        TECSCDE::TECSModel::TmEPort.new(self, @port_def, subscript)
+      end
+    end
+  end
+end

data/lib/tecscde/tecs_model/tm_join.rb

@@ -0,0 +1,293 @@
+#
+# TECSCDE - TECS Component Diagram Editor
+#
+# Copyright (C) 2014-2019 by TOPPERS Project
+#
+#  The above copyright holders grant permission gratis to use,
+#  duplicate, modify, or redistribute (hereafter called use) this
+#  software (including the one made by modifying this software),
+#  provided that the following four conditions (1) through (4) are
+#  satisfied.
+#
+#  (1) When this software is used in the form of source code, the above
+#      copyright notice, this use conditions, and the disclaimer shown
+#      below must be retained in the source code without modification.
+#
+#  (2) When this software is redistributed in the forms usable for the
+#      development of other software, such as in library form, the above
+#      copyright notice, this use conditions, and the disclaimer shown
+#      below must be shown without modification in the document provided
+#      with the redistributed software, such as the user manual.
+#
+#  (3) When this software is redistributed in the forms unusable for the
+#      development of other software, such as the case when the software
+#      is embedded in a piece of equipment, either of the following two
+#      conditions must be satisfied:
+#
+#    (a) The above copyright notice, this use conditions, and the
+#        disclaimer shown below must be shown without modification in
+#        the document provided with the redistributed software, such as
+#        the user manual.
+#
+#    (b) How the software is to be redistributed must be reported to the
+#        TOPPERS Project according to the procedure described
+#        separately.
+#
+#  (4) The above copyright holders and the TOPPERS Project are exempt
+#      from responsibility for any type of damage directly or indirectly
+#      caused from the use of this software and are indemnified by any
+#      users or end users of this software from any and all causes of
+#      action whatsoever.
+#
+#  THIS SOFTWARE IS PROVIDED "AS IS." THE ABOVE COPYRIGHT HOLDERS AND
+#  THE TOPPERS PROJECT DISCLAIM ANY EXPRESS OR IMPLIED WARRANTIES,
+#  INCLUDING, BUT NOT LIMITED TO, ITS APPLICABILITY TO A PARTICULAR
+#  PURPOSE. IN NO EVENT SHALL THE ABOVE COPYRIGHT HOLDERS AND THE
+#  TOPPERS PROJECT BE LIABLE FOR ANY TYPE OF DAMAGE DIRECTLY OR
+#  INDIRECTLY CAUSED FROM THE USE OF THIS SOFTWARE.
+#
+
+require "tecscde/tm_object"
+require "tecscde/tecs_model/hbar"
+require "tecscde/tecs_model/vbar"
+
+module TECSCDE
+  class TECSModel
+    class TmJoin < TECSCDE::TmObject
+      # @cport::TmCPort
+      # @eport::TmEPort
+      # @bars::[TECSCDE::TECSModel::HBar|TECSCDE::TECSModel::VBar]
+      # @owner::TECSModel
+
+      include TECSCDE::TECSModel::TmUneditable
+
+      attr_reader :bars, :cport, :eport
+
+      def initialize(cport, eport, tmodel)
+        @cport = cport
+        @eport = eport
+        @owner = tmodel
+
+        cport.set_join(self)
+        eport.add_join(self)
+
+        create_bars
+        # @bars.each{ |bar| bar.set_join self }
+
+        @editable = true
+        modified {}
+      end
+
+      #=== TmJoin#create_bars_to dest_port
+      def create_bars
+        if TECSCDE::TECSModel.parallel?(@cport.get_edge_side, @eport.get_edge_side)
+          if TECSCDE::TECSModel.opposite?(@cport.get_edge_side, @eport.get_edge_side)
+            create_bars_a
+          else
+            create_bars_e
+          end
+        else
+          create_bars_c
+        end
+      end
+
+      def create_bar(bar, position)
+        if bar.horizontal?
+          TECSCDE::TECSModel::VBar.new(position, self)
+        else
+          TECSCDE::TECSModel::HBar.new(position, self)
+        end
+      end
+
+      #=== TmJoin#create_bars_a
+      # (a) parallel opposite side generic
+      def create_bars_a
+        @bars = []
+
+        @bars[0] = @cport.get_normal_bar_of_edge(self)
+
+        posa = @cport.get_position_in_tangential_dir
+        e1, e2 = @eport.get_cell.get_right_angle_edges_position(@cport.get_edge_side)
+        # p "posa=#{posa} e1=#{e1}, e2=#{e2}"
+        pos1 = ((posa - e1).abs > (posa - e2).abs) ? (e2 + GAP) : (e1 - Gap)
+        @bars[1] = create_bar(@bars[0], pos1)
+
+        pos2 = @eport.get_position_in_normal_dir + EPGAP * @eport.get_sign_of_normal
+        @bars[2] = create_bar(@bars[1], pos2)
+
+        pos3 = @eport.get_position_in_tangential_dir
+        @bars[3] = create_bar(@bars[2], pos3)
+
+        pos4 = @eport.get_position_in_normal_dir
+        @bars[4] = create_bar(@bars[3], pos4)
+      end
+
+      #=== TmJoin#create_bars_c
+      # (c) right angle generic
+      def create_bars_c
+        @bars = []
+
+        @bars[0] = @cport.get_normal_bar_of_edge(self)
+
+        pos1 = @eport.get_position_in_normal_dir + EPGAP * @eport.get_sign_of_normal
+        @bars[1] = create_bar(@bars[0], pos1)
+
+        pos2 = @eport.get_position_in_tangential_dir
+        @bars[2] = create_bar(@bars[1], pos2)
+
+        pos3 = @eport.get_position_in_normal_dir
+        @bars[3] = create_bar(@bars[2], pos3)
+      end
+
+      #=== TmJoin#create_bars_e
+      # (e) parallel same side generic
+      def create_bars_e
+        @bars = []
+
+        @bars[0] = @cport.get_normal_bar_of_edge(self)
+
+        posa = @cport.get_position_in_tangential_dir
+        e1, e2 = @eport.get_cell.get_right_angle_edges_position(@cport.get_edge_side)
+        pos1 = ((posa - e1).abs > (posa - e2).abs) ? (e2 + GAP) : (e1 - Gap)
+        @bars[1] = create_bar(@bars[0], pos1)
+
+        pos2 = @eport.get_position_in_normal_dir + EPGAP * @eport.get_sign_of_normal
+        @bars[2] = create_bar(@bars[1], pos2)
+
+        pos3 = @eport.get_position_in_tangential_dir
+        @bars[3] = create_bar(@bars[2], pos3)
+
+        pos4 = @eport.get_position_in_normal_dir
+        @bars[4] = create_bar(@bars[3], pos4)
+      end
+
+      def moved_cport(x_inc, y_inc)
+        if @bars[0].instance_of?(TECSCDE::TECSModel::VBar)
+          @bars[0].moved(y_inc)
+        else
+          @bars[0].moved(x_inc)
+        end
+      end
+
+      def moved_eport(x_inc, y_inc)
+        TECSCDE.logger.debug("moved_eport=(#{x_inc} #{y_inc})")
+        len = @bars.length
+
+        if len >= 5
+          if @bars[len - 4].instance_of?(TECSCDE::TECSModel::VBar)
+            @bars[len - 4].moved(y_inc)
+          else
+            @bars[len - 4].moved(x_inc)
+          end
+        end
+
+        if len >= 4
+          if @bars[len - 3].instance_of?(TECSCDE::TECSModel::VBar)
+            @bars[len - 3].moved(y_inc)
+          else
+            @bars[len - 3].moved(x_inc)
+          end
+        end
+
+        if len >= 3
+          if @bars[len - 2].instance_of?(TECSCDE::TECSModel::VBar)
+            @bars[len - 2].moved(y_inc)
+          else
+            @bars[len - 2].moved(x_inc)
+          end
+        end
+
+        if @bars[len - 1].instance_of?(TECSCDE::TECSModel::VBar)
+          @bars[len - 1].moved(y_inc)
+        else
+          @bars[len - 1].moved(x_inc)
+        end
+      end
+
+      #=== TmJoin#get_near_bar ***
+      def get_near_bar(xm, ym)
+        xs, ys = @cport.get_position
+        xe = xs
+        ye = ys
+        min_dist = 999999999
+        min_bar = nil
+        @bars.each do |bar|
+          if bar.horizontal?
+            xe = bar.get_position
+            if between?(xm, xs, xe) && near?(ym, ys)
+              dist = (ym - ys).abs
+              if dist < min_dist
+                min_dist = dist
+                min_bar = bar
+              end
+            end
+          else # VBar
+            ye = bar.get_position
+            if between?(ym, ys, ye) && near?(xm, xs)
+              dist = (xm - xs).abs
+              if dist < min_dist
+                min_dist = dist
+                min_bar = bar
+              end
+            end
+          end
+          xs = xe
+          ys = ye
+        end
+        [min_bar, min_dist]
+      end
+
+      #=== TmJoin#between?
+      # RETURN:: true if x is between a & b
+      def between?(x, a, b)
+        if a >= b
+          if b <= x && x <= a
+            true
+          else
+            false
+          end
+        else
+          if a <= x && x <= b
+            true
+          else
+            false
+          end
+        end
+      end
+
+      #=== TmJoin#near?
+      def near?(x, a)
+        (x - a).abs < NEAR_DIST
+      end
+
+      #=== TmJoin#change_bars bars
+      def change_bars(bars)
+        modified do
+          @bars = bars
+        end
+      end
+
+      #=== TmJoin#get_signature ***
+      def get_signature
+        @cport.get_signature
+      end
+
+      #=== TmJoin#delete ***
+      def delete
+        return unless editable?
+        modified do
+          @cport.delete_join
+          @eport.delete_join(self)
+          @owner.delete_join(self)
+        end
+      end
+
+      #=== TmJoin#clone_for_undo
+      def clone_for_undo
+        bu = clone
+        bu.copy_from(self)
+        bu
+      end
+    end
+  end
+end