denko 0.13.6 → 0.14.0

data/examples/pulse_io/ir_transmitter.rb

@@ -1,55 +0,0 @@
-#
-# This is a simple test of the IREmitter (infrared blaster) class.
-# It is based on this example from the Arduino library:
-# https://github.com/Arduino-IRremote/Arduino-IRremote/tree/master/examples/SendDemo
-#
-# To verify your emitter is working, you can flash this sketch on a second board:
-# https://github.com/Arduino-IRremote/Arduino-IRremote/tree/master/examples/ReceiveDemo
-#
-# Attach an IR receiver to the receive pin (2 for Atmel AVR) and observe for serial output.
-#
-# If you don't have 2 boards, use the receive sketch to capture a code from a button
-# of a remote you have. Copy the raw code (long list of numbers in curly braces),
-# and modify it into a Ruby array. 
-#
-# Reflash the denko sketch onto your board and test the IR code operates your device.
-#
-# Both of these methods require you to have an IR receiver handy.
-# If you do not have one, there are IR codes in Raw format for many devices
-# available on sites like http://irdb.tk/codes/
-# When formatted as a string of numbers with + and - in front of each number,
-# you will need to convert them to the array format before use.
-#
-require 'bundler/setup'
-require 'denko'
-
-# Note: If testing with 2 boards connected to the same computer, you want to be
-# explicit about which serial device this script must use. The relevant
-# Connection call is below, but commented out. Enable it and substitute the approriate
-# device  for the board that has the IR emitter connected and denko sketch loaded.
-# Open the receiver board in the Arduino IDE's or another serial monitor.
-#
-connection = Denko::Connection::Serial.new
-# connection = Denko::Connection::Serial.new(device: "/dev/ttyACM0")
-board = Denko::Board.new(connection)
-
-#
-# The IR emitter can be set up on most pins for most boards, but there might be conflicts
-# with other hardware or libraries. Try different pins if one doesn't work.
-#
-ir = Denko::PulseIO::IRTransmitter.new(board: board, pin: 3)
-
-# NEC Raw-Data=0xF708FB04. LSBFIRST, so the binary for each hex digit below is backward.
-code =  [ 9000, 4500,                                 # Start bit
-          560, 560, 560, 560, 560, 1690, 560, 560,    # 0010 0x4 command
-          560, 560, 560, 560, 560, 560, 560, 560,     # 0000 0x0 command
-          560, 1690, 560, 1690, 560,560, 560, 1690,   # 1101 0xB command inverted
-          560, 1690, 560, 1690, 560, 1690, 560, 1690, # 1111 0xF command inverted
-          560, 560, 560, 560, 560, 560, 560, 1690,    # 0001 0x8 address
-          560, 560, 560, 560, 560, 560, 560, 560,     # 0000 0x0 address
-          560, 1690, 560, 1690, 560, 1690, 560, 560,  # 1110 0x7 address inverted
-          560, 1690, 560, 1690, 560, 1690, 560, 1690, # 1111 0xF address inverted
-          560]                                        # Stop bit
-
-ir.emit(code)
-board.finish_write

data/examples/spi/ssd_through_register.rb

@@ -1,40 +0,0 @@
-#
-# Example of SevenSegment LED driven though an output shift register (74HC595).
-# Can be used on either a bit bang or hardware SPI interface.
-#
-require 'bundler/setup'
-require 'denko'
-
-# SPI pins (on board)
-SPI_BIT_BANG_PINS   = { clock: 13, output: 11 }
-REGISTER_SELECT_PIN = 10
-
-# SevenSegment pins (on register parallel outputs)
-SEVEN_SEGMENT_PINS = { cathode: 0, a: 1, b: 2, c: 3, d: 4, e: 5, f: 6, g: 7 }
-
-board = Denko::Board.new(Denko::Connection::Serial.new)
-
-# 1-way bit bang SPI bus (slower, but use any pins).
-bus = Denko::SPI::BitBang.new(board: board, pins: SPI_BIT_BANG_PINS)
-
-# Use the default hardware SPI bus (faster, but predetermined pins).
-# bus = Denko::SPI::Bus.new(board: board)
-
-# Show the hardware SPI pins to aid connection.
-# MOSI = output | MISO = input | SCK = clock
-# puts board.map.select { |name, number| [:MOSI, :MISO, :SCK].include?(name) }
-
-# OutputRegister needs a bus and its select pin.
-register = Denko::SPI::OutputRegister.new(bus: bus, pin: REGISTER_SELECT_PIN)
-
-#
-# OutputRegister implements enough of the Board interface that digital output
-# components can treat it as a Board. Do that with the SSD.
-#
-ssd = Denko::LED::SevenSegment.new(board: register, pins: SEVEN_SEGMENT_PINS)
-
-# Turn off the ssd on exit.
-trap("SIGINT") { exit !ssd.off }
-
-# Type a character and press Enter to show it on the SevenSegment LED.
-loop { ssd.display(gets.chomp) }

data/examples/uart/bit_bang_read.rb

@@ -1,16 +0,0 @@
-#
-# Example that writes to hardware UART1 and reads back on bit bang UART. Tested on Arduino Mega.
-#
-require 'bundler/setup'
-require 'denko'
-
-board = Denko::Board.new(Denko::Connection::Serial.new)
-
-hw_uart = Denko::UART::Hardware.new(board: board, index: 1, baud: 31250)
-bb_uart = Denko::UART::BitBang.new(board: board, pins: { rx:10, tx:11 }, baud: 31250)
-
-hw_uart.write("Hello World!\n")
-
-sleep 1
-
-puts bb_uart.gets

data/examples/uart/bit_bang_write.rb

@@ -1,16 +0,0 @@
-#
-# Example that writes to bit bang UART and reads back on hardware UART1. Tested on Arduino Mega.
-#
-require 'bundler/setup'
-require 'denko'
-
-board = Denko::Board.new(Denko::Connection::Serial.new)
-
-hw_uart = Denko::UART::Hardware.new(board: board, index: 1, baud: 31250)
-bb_uart = Denko::UART::BitBang.new(board: board, pins: { rx:10, tx:11 }, baud: 31250)
-
-bb_uart.write("Hello World!\n")
-
-sleep 1
-
-puts hw_uart.gets

data/lib/denko/analog_io/sensor.rb

@@ -1,6 +0,0 @@
-module Denko
-  module AnalogIO
-    class Sensor < Input
-    end
-  end
-end

data/lib/denko/sensor/virtual.rb

@@ -1,42 +0,0 @@
-module Denko
-  module Sensor
-    class Temperature
-      include Behaviors::Poller
-
-      def initialize(sensor)
-        @sensor = sensor
-        super
-      end
-
-      def _read
-        @sensor.read_temperature
-      end
-
-      alias :celsius :state
-      alias :to_i    :state
-
-      def fahrenheit
-        (celsius * 9 / 5) + 32
-      end
-
-      def kelvin
-        celsius + 273.15
-      end
-    end
-
-    class Humidity
-      include Behaviors::Poller
-
-      def initialize(sensor)
-        @sensor = sensor
-        super
-      end
-
-      def _read
-        @sensor.read_humidity
-      end
-
-      alias :to_i :state
-    end
-  end
-end

data/src/lib/DenkoIROutESP.cpp

@@ -1,26 +0,0 @@
-//
-// Denko IR output for the ESP8266 and ESP32.
-// Depends on: https://github.com/crankyoldgit/IRremoteESP8266
-// DENKO_IR_OUT must be defeind in DenkoDefines.h
-//
-#include "Denko.h"
-#if defined(DENKO_IR_OUT) && (defined(ESP8266) || defined(ESP32))
-
-#include <IRremoteESP8266.h>
-#include <IRsend.h>
-
-// CMD = 16
-// Send an infrared signal.
-void Denko::irSend(){
-  // Byte 1+ of auxMsg is already little-endian uint16 pulses.
-  uint16_t *pulseArray = reinterpret_cast<uint16_t *>(auxMsg + 1);
-  
-  // Can work on any pin.
-  IRsend infraredOut(pin);
-  infraredOut.begin();
-  
-  // auxMsg[0] is how many pulses were packed.
-  // val is frequency
-  infraredOut.sendRaw(pulseArray, auxMsg[0], val);
-}
-#endif

data/vendor/board-maps/yaml/STAMP_S3.yml

@@ -1,8 +0,0 @@
----
-:D2: 2
-:SS: 7
-:MOSI: 6
-:MISO: 5
-:SCK: 4
-:SDA: 13
-:SCL: 15