ecoengine 3.1.6__tar.gz → 3.2.0__tar.gz

{ecoengine-3.1.6 → ecoengine-3.2.0}/PKG-INFO

@@ -1,10 +1,10 @@
 Metadata-Version: 2.4
 Name: ecoengine
-Version: 3.1.6
-Requires-Python: <3.12,>=3.11
-Requires-Dist: numpy~=1.24.1
-Requires-Dist: scipy<2.0,>=1.10
-Requires-Dist: plotly==5.19.0
+Version: 3.2.0
+Requires-Python: >=3.11
+Requires-Dist: numpy<3.0,>=2.4
+Requires-Dist: scipy<2.0,>=1.17
+Requires-Dist: plotly<8.0,>=7.0
 Provides-Extra: docs
 Requires-Dist: sphinx>=6; extra == "docs"
 Requires-Dist: furo; extra == "docs"

{ecoengine-3.1.6 → ecoengine-3.2.0}/README.md

@@ -5,7 +5,7 @@ This program comes with ABSOLUTELY NO WARRANTY. This is free software, and you a
 
 A Python simulation engine for sizing and simulating domestic hot water (DHW) systems in multi-family and commercial buildings, with a focus on heat pump water heater (HPWH) technology.
 
-Requires Python 3.11 (capped below 3.12). Dependencies: `numpy`, `scipy`, `plotly`.
+Requires Python 3.11 or newer. Dependencies: `numpy`, `scipy`, `plotly`.
 
 Version bounds are deliberate. `ecoengine` is installed into the same environments as `ecopipeline` (DataPipelinePackage) and `rcc-dash-viewer` (RCCDashViewer, which depends on `ecoengine` directly), so the pins are set to resolve alongside both. See the comments in `pyproject.toml` before loosening them.
 

{ecoengine-3.1.6 → ecoengine-3.2.0}/pyproject.toml

@@ -4,33 +4,34 @@ build-backend = "setuptools.build_meta"
 
 [project]
 name = "ecoengine"
-version = "3.1.6"
-requires-python = ">=3.11,<3.12"
+version = "3.2.0"
+requires-python = ">=3.11"
 
-# Upper bounds are deliberate, and match the bounds in ecopipeline
-# (DataPipelinePackage).  Coworkers install both packages into the same
+# Ranges are bounded on purpose, and the shared ones are kept in sync with
+# ecopipeline (DataPipelinePackage) and rcc-dash-viewer (RCCDashViewer, which
+# depends on ecoengine directly).  All three get installed into the same
 # long-lived environments, so an unbounded range lets a routine `pip install`
-# pull in a release that satisfies one package and breaks the other (numpy 2.x
-# against pandas 1.5.x being the recurring case there).  The Python cap exists
-# for the same reason: ecopipeline is capped at <3.12, so an uncapped ecoengine
-# would allow a 3.12 environment that ecopipeline cannot join.
+# pull a release that satisfies one package and breaks another.  Note that a
+# clean resolution is not proof of a working environment: pandas 1.5.3 declared
+# no numpy ceiling, so it resolved happily against numpy 2 and then failed at
+# import with a binary-incompatibility ValueError.  That is what these bounds
+# are for.  When bumping a shared range, bump it in all three repos together.
 #
 # scipy is not imported anywhere in this source tree.  It is required at runtime
 # to unpickle the LinearNDInterpolator objects in data/preformanceMaps/pkls/,
 # which PklPerformanceMap loads.  Do not remove it on the basis of an import
 # scan.  The <2.0 ceiling is not precautionary: scipy.interpolate.interpnd is
-# deprecated and is removed in SciPy 2.0, which will break those pickles.  The
-# range has been exercised at 1.10.0, 1.11.1, and 1.15.3 against numpy 1.24.x.
+# deprecated and is removed in SciPy 2.0, which will break those pickles.
+# scipy also gates numpy indirectly — 1.16 requires numpy>=1.25.2 and 1.17
+# requires numpy>=1.26.4 — so the scipy floor and the numpy floor move together.
 #
-# plotly is pinned exactly rather than ranged, to match rcc-dash-viewer
-# (RCCDashViewer), which depends on ecoengine directly and hard-pins
-# plotly==5.19.0.  Keeping the two identical means the figures this package
-# generates render against the same plotly the dashboard ships.  Bump both
-# together or not at all.
+# Verified against numpy 2.4.6 / scipy 1.17.1 / plotly 7.0.0: full test suite,
+# all six performance-map pickles, and the to_plotly / plot_sizing_curve /
+# write_html output paths.
 dependencies = [
-    "numpy~=1.24.1",
-    "scipy>=1.10,<2.0",
-    "plotly==5.19.0",
+    "numpy>=2.4,<3.0",
+    "scipy>=1.17,<2.0",
+    "plotly>=7.0,<8.0",
 ]
 
 [project.optional-dependencies]

{ecoengine-3.1.6 → ecoengine-3.2.0}/src/ecoengine.egg-info/PKG-INFO

@@ -1,10 +1,10 @@
 Metadata-Version: 2.4
 Name: ecoengine
-Version: 3.1.6
-Requires-Python: <3.12,>=3.11
-Requires-Dist: numpy~=1.24.1
-Requires-Dist: scipy<2.0,>=1.10
-Requires-Dist: plotly==5.19.0
+Version: 3.2.0
+Requires-Python: >=3.11
+Requires-Dist: numpy<3.0,>=2.4
+Requires-Dist: scipy<2.0,>=1.17
+Requires-Dist: plotly<8.0,>=7.0
 Provides-Extra: docs
 Requires-Dist: sphinx>=6; extra == "docs"
 Requires-Dist: furo; extra == "docs"

ecoengine-3.2.0/src/ecoengine.egg-info/requires.txt

@@ -0,0 +1,7 @@
+numpy<3.0,>=2.4
+scipy<2.0,>=1.17
+plotly<8.0,>=7.0
+
+[docs]
+sphinx>=6
+furo

ecoengine-3.1.6/src/ecoengine.egg-info/requires.txt

@@ -1,7 +0,0 @@
-numpy~=1.24.1
-scipy<2.0,>=1.10
-plotly==5.19.0
-
-[docs]
-sphinx>=6
-furo