com2tty 0.1.2__tar.gz → 0.2.0__tar.gz

com2tty-0.2.0/PKG-INFO

@@ -0,0 +1,653 @@
+Metadata-Version: 2.4
+Name: com2tty
+Version: 0.2.0
+Summary: A Windows COM port to WSL ttyUSB forwarder
+Author-email: yichengs <yichengs.tw+com2tty@gmail.com>
+Project-URL: Homepage, https://github.com/Yi-Cheng-Wang/com2tty
+Classifier: Programming Language :: Python :: 3
+Classifier: License :: OSI Approved :: MIT License
+Classifier: Operating System :: Microsoft :: Windows
+Classifier: Operating System :: POSIX :: Linux
+Requires-Python: >=3.8
+Description-Content-Type: text/markdown
+License-File: LICENSE
+Requires-Dist: pyserial>=3.5
+Dynamic: license-file
+
+# com2tty
+
+`com2tty` is a Python package that runs on a Windows host and forwards a device
+attached to Windows into a Windows Subsystem for Linux (WSL) instance, where it
+appears as a native Linux device. It supports two kinds of forwarding. The first
+forwards a Windows COM port into WSL as a virtual serial device such as
+`/tmp/ttyUSB0`. The second forwards a Windows XInput game controller into WSL as
+a Linux evdev gamepad. Both kinds use the same transport: a low-latency,
+firewall-resilient bridge built on standard input and output redirection between
+the Windows host process and a helper process running inside WSL. No network
+configuration, port forwarding, or firewall change is required.
+
+The intended users are developers who work inside WSL but whose hardware is bound
+to the Windows host: embedded developers who flash and monitor microcontrollers
+over USB-to-serial adapters, and developers who need a game controller available
+to Linux tools running in WSL.
+
+## Table of contents
+
+- [Requirements](#requirements)
+- [Installation](#installation)
+- [Configuration](#configuration)
+- [Usage](#usage)
+  - [Listing available ports](#listing-available-ports)
+  - [Bridging a serial port](#bridging-a-serial-port)
+  - [Hot-plug auto-reconnect](#hot-plug-auto-reconnect)
+  - [Bridging multiple ports](#bridging-multiple-ports)
+  - [Argument profiles](#argument-profiles)
+  - [Automatic baud-rate detection](#automatic-baud-rate-detection)
+  - [Configuring /dev/ttyUSB0 in WSL](#configuring-devttyusb0-in-wsl)
+  - [Firmware upload through the bridge](#firmware-upload-through-the-bridge)
+  - [Gamepad mode](#gamepad-mode)
+- [Architecture overview](#architecture-overview)
+- [Development setup](#development-setup)
+- [Contributing](#contributing)
+- [Troubleshooting](#troubleshooting)
+- [License](#license)
+
+## Requirements
+
+The Windows host requires Python 3.8 or later. The `pyserial` package, version
+3.5 or later, is the only runtime dependency and is installed automatically with
+the package. A working WSL installation is required, and the WSL distribution
+must provide `python3` on its `PATH`. By default the WSL default distribution
+is used; a specific one can be selected with `--distro`. The WSL helper uses
+only the Python standard library and therefore needs no additional packages
+inside WSL. These prerequisites are verified at startup and a specific,
+actionable error is reported when one is missing.
+
+Serial forwarding requires a COM port that Windows can open. Gamepad forwarding
+requires a controller that the Windows XInput driver recognises, which is the
+standard case for Xbox and XInput-compatible controllers. The opt-in gamepad tier
+that creates a real Linux input device additionally requires a one-time
+privileged setup inside WSL, described in [Gamepad mode](#gamepad-mode).
+
+## Installation
+
+Install the released package from PyPI on the Windows host.
+
+```cmd
+pip install com2tty
+```
+
+Alternatively, install from a checkout of the source by running the following
+in the project root.
+
+```cmd
+pip install .
+```
+
+To work on the package itself, install it in editable mode.
+
+```cmd
+pip install -e .
+```
+
+Installation registers a console entry point named `com2tty`. If the entry point
+is not on your `PATH`, the package can also be invoked as a module with
+`python -m com2tty`.
+
+## Configuration
+
+`com2tty` is configured through command-line arguments, optionally saved as
+named profiles in an INI file (see
+[Argument profiles](#argument-profiles)). Note that in serial mode the WSL
+helper writes environment variables into the WSL user's shell configuration;
+this behaviour is described in
+[Firmware upload through the bridge](#firmware-upload-through-the-bridge).
+
+The positional arguments are the COM ports. At least one is required in
+serial mode; several may be given to bridge them concurrently. The port is
+omitted in gamepad mode, which is selected with `--gamepad`, and in the
+`--list` and `--version` modes.
+
+### Options common to both modes
+
+The following options apply to both modes.
+
+```text
+--version              Print the com2tty version and exit.
+-l, --list             List the serial ports Windows can see (device name,
+                       VID:PID, USB bus id, serial number, detected board,
+                       description) and exit.
+-d, --debug            Enable verbose debug logging on standard error.
+--distro NAME          WSL distribution to use (default: the WSL default
+                       distribution). Useful when the default distribution
+                       lacks python3, for example docker-desktop.
+```
+
+### Serial-mode options
+
+```text
+port [port ...]        Windows COM port(s) to bridge, for example COM3, or
+                       COM3 COM5 to bridge two ports at once. Required
+                       unless --gamepad or --list is given.
+-b, --baud BAUD        Baud rate, or the literal value "auto" to detect the
+                       rate Windows has configured for the port
+                       (default: auto; falls back to 9600 if detection fails).
+-w, --wsl-tty PATH     Target symlink path created inside WSL
+                       (default: /tmp/ttyUSB0). With multiple ports, each
+                       additional port increments the trailing number.
+--rfc2217-port PORT    TCP port for the in-WSL RFC 2217 forwarder
+                       (default: 4000). The UF2 relay uses PORT + 1; with
+                       multiple ports, each additional port uses PORT + 2i.
+--bytesize {5,6,7,8}   Serial byte size (default: 8).
+--parity {N,E,O,S,M}   Parity: none, even, odd, space, or mark (default: N).
+--stopbits {1,1.5,2}   Stop bits (default: 1).
+--xonxoff              Enable software flow control (XON/XOFF).
+--rtscts               Enable hardware flow control (RTS/CTS).
+--dsrdtr               Enable hardware flow control (DSR/DTR).
+--board {auto,esp32,pico,nrf52,samd,stm32,none}
+                       Override USB VID board detection for reset and upload
+                       handling (default: auto). Use this when a board uses a
+                       USB-UART chip that com2tty does not recognise; "none"
+                       disables board-specific reset sequences entirely.
+```
+
+### Gamepad-mode options
+
+```text
+--gamepad              Select gamepad mode. No COM port is required.
+--pad-index {0,1,2,3}  XInput controller slot to forward (default: 0).
+--pad-name NAME        Device name advertised inside WSL
+                       (default: "Microsoft X-Box 360 pad").
+--uinput               Create a real /dev/input device through /dev/uinput
+                       instead of the default /tmp event stream.
+--wsl-pad PATH         FIFO path for the default /tmp event stream
+                       (default: /tmp/com2pad0).
+--poll-hz HZ           XInput polling rate in hertz (default: 250). Frames are
+                       sent only when the controller state changes.
+```
+
+## Usage
+
+Run `com2tty` from any Windows terminal, either PowerShell or Command Prompt. The
+process runs in the foreground and is stopped with Ctrl+C.
+
+### Listing available ports
+
+`com2tty --list` (or `-l`) enumerates every serial port Windows can see,
+without requiring usbipd or administrator rights.
+
+```text
+> com2tty --list
+Device  VID:PID    Bus ID  Serial number     Board    Description
+------  ---------  ------  ----------------  -------  -----------------------
+COM3    -          -       -                 unknown  Bluetooth serial (COM3)
+COM17   2E8A:F00F  1-6     98C4FFA253A63FB7  pico     USB serial device (COM17)
+```
+
+The `Bus ID` column is the USB bus location (for example `1-6` or `2-6`), read
+directly from the device descriptor. The `Board` column shows the family that
+VID-based detection would assign, which is the same detection the bridge uses
+for reset and upload handling.
+
+### Bridging a serial port
+
+Bridge `COM3` to the default WSL path `/tmp/ttyUSB0` at 115200 baud.
+
+```cmd
+com2tty COM3 --baud 115200
+```
+
+Bridge `COM5` to a custom WSL device path at 9600 baud.
+
+```cmd
+com2tty COM5 --baud 9600 -w /tmp/my_device
+```
+
+While the bridge is active, a Linux program inside WSL opens the symlinked path
+and reads from and writes to it as if it were a local serial device. Data is
+relayed in both directions between the Windows COM port and the WSL pseudo
+terminal. Dynamic changes that a WSL program makes to the line settings, such as
+the baud rate, are detected and applied to the underlying Windows COM port.
+
+### Hot-plug auto-reconnect
+
+When the bridged device is unplugged, resets, or re-enumerates, the bridge
+does not need to be restarted. After a short grace period for transient
+errors (such as a board rebooting into its bootloader), com2tty closes the
+stale Windows handle and waits for the device to come back, first under its
+original COM name and then by scanning for its USB serial number, because
+Windows may assign a different COM number after a replug. Once the device
+reappears the bridge resumes automatically; the WSL endpoint stays in place
+the whole time.
+
+### Bridging multiple ports
+
+Passing several ports bridges them all from one invocation.
+
+```cmd
+com2tty COM3 COM5
+```
+
+Each port gets its own WSL helper and endpoint: the symlink path is derived
+from `--wsl-tty` by incrementing its trailing number (`/tmp/ttyUSB0`,
+`/tmp/ttyUSB1`, ...), and the RFC 2217 port is the base value plus two per
+additional port (each bridge also reserves its port plus one for the UF2
+relay). Only the first port writes the PlatformIO environment variables and
+intercepts `picotool`, so concurrent bridges do not overwrite each other's
+shell configuration; tools targeting a secondary port can use its RFC 2217
+port directly.
+
+### Argument profiles
+
+Frequently used argument sets can be saved as named profiles in an INI file,
+either `com2tty.ini` in the current directory or `.com2tty.ini` in the user
+profile directory. Keys are the long option names (dashes and underscores are
+both accepted), `port` supplies the positional argument, and boolean keys
+take `true` or `false`.
+
+```ini
+[myboard]
+port = COM5
+baud = 115200
+wsl-tty = /tmp/my_device
+board = pico
+
+[pad]
+gamepad = true
+uinput = true
+```
+
+A profile is invoked with an `@` prefix, and arguments given after the token
+override the profile's values.
+
+```cmd
+com2tty @myboard
+com2tty @myboard --baud 9600
+com2tty @pad
+```
+
+### Automatic baud-rate detection
+
+When the baud rate is left at its default value of `auto`, com2tty queries the
+rate that Windows has configured for the port and uses it. If detection fails,
+the bridge falls back to 9600 baud. To set the rate explicitly, pass a numeric
+value to `--baud`.
+
+```cmd
+com2tty COM3 --baud auto
+```
+
+### Configuring /dev/ttyUSB0 in WSL
+
+In Linux the `/dev` directory is owned by `root`. Running com2tty as an ordinary
+Windows user means the WSL helper cannot create a symlink directly under `/dev`.
+For this reason the default target is `/tmp/ttyUSB0`, which is user-writable, and
+com2tty never requires elevated privileges at run time. If a path under `/dev` is
+requested and permission is denied, the helper automatically falls back to the
+equivalent path under `/tmp` and prints instructions.
+
+To expose the device at a stable `/dev` path without granting com2tty privileges,
+create a one-time symlink inside WSL that points from `/dev` to the stable `/tmp`
+path.
+
+```bash
+sudo ln -sf /tmp/ttyUSB0 /dev/ttyUSB0
+```
+
+Each time com2tty starts, it repoints `/tmp/ttyUSB0` at the active pseudo
+terminal, so `/dev/ttyUSB0` continues to resolve correctly. After this one-time
+step, WSL programs such as `minicom`, `screen`, the ESP-IDF tools, or Python
+scripts can use `/dev/ttyUSB0` directly.
+
+### Firmware upload through the bridge
+
+In serial mode com2tty additionally supports flashing microcontroller firmware
+from build tools running inside WSL, so that a PlatformIO project in WSL can
+upload to a board attached to Windows. This support is enabled by default and
+involves three mechanisms.
+
+First, the WSL helper starts an RFC 2217 forwarder that listens on
+`127.0.0.1:<rfc2217-port>` inside WSL, where the port defaults to 4000. To make
+PlatformIO use it, the helper appends environment variables to the WSL user's
+shell startup file: `PLATFORMIO_UPLOAD_PORT` is set to
+`rfc2217://127.0.0.1:<rfc2217-port>` and `PLATFORMIO_MONITOR_PORT` is set to the
+serial symlink path. The variables are written to `~/.bashrc`, to `~/.zshrc`
+when zsh is in use or that file exists, and to
+`~/.config/fish/conf.d/com2tty.fish` when fish is in use or its configuration
+directory exists. Open a new WSL shell or run `source ~/.bashrc` (or
+`source ~/.zshrc`; fish picks the snippet up automatically) after starting
+com2tty for them to take effect. The variables are removed when com2tty exits;
+if a session is killed before it can clean up, the next run removes the stale
+block on startup.
+
+Second, com2tty detects the connected board type from its USB vendor identifier
+and performs the appropriate hardware reset on the Windows side. For ESP32-class
+boards it performs the DTR and RTS auto-reset sequence to enter the download
+mode. For RP2040 and RP2350 boards, and for Adafruit nRF52 boards with the UF2
+bootloader, it performs the 1200-baud touch that triggers the mass-storage
+bootloader mode. For Arduino Leonardo- and SAMD-class boards it performs the
+same 1200-baud touch; because their bootloader re-enumerates as a separate
+serial port (often with a different USB identity than the application port),
+com2tty snapshots the port list before the touch, waits for the new bootloader
+port to appear, opens it, and runs the upload against it over RFC 2217. When the
+upload finishes and the board reboots into the application, com2tty restores and
+reopens the original application port. For STM32-class boards it pulses
+DTR and RTS in the conventional BOOT0/NRST wiring so the board resets around
+an upload; boards flashed through ST-LINK or DFU are unaffected by the pulse.
+
+Third, for UF2-bootloader boards (RP2040, RP2350, and nRF52), com2tty
+intercepts the `picotool` invocation
+inside WSL. When PlatformIO calls `picotool` to flash a `.uf2` image, a wrapper
+transfers the image back to the Windows host over a relay that listens on
+`127.0.0.1:<rfc2217-port + 1>`. The host then triggers BOOTSEL mode, locates the
+board's mass-storage drive, verifies the transferred image against an MD5
+checksum, and writes the image to the drive. The original `picotool` is restored
+when com2tty exits; if a session is killed before it can restore it, the next run
+detects and reverses the leftover interception on startup, so PlatformIO uploads
+are not left broken.
+
+These mechanisms operate without any additional flags. The startup banner reports
+the detected board type, the RFC 2217 port, the UF2 relay port, and the board's
+USB serial number. If the detected board type is wrong (for example a board whose
+USB-UART chip is not recognised), override it with `--board`.
+
+The RFC 2217 forwarder and the UF2 relay listen on the loopback interface
+(`127.0.0.1`) inside the WSL distribution and perform no authentication. On a
+single-user machine this is not exposed to the network, but on a shared or
+multi-user WSL host any local user in the same distribution could connect to
+these ports during an upload. Run com2tty only on hosts you trust, and choose a
+non-default `--rfc2217-port` if another local service needs the default port. To
+reclaim a port left open by a previous com2tty session, the helper only
+terminates processes whose command line identifies them as a com2tty bridge; an
+unrelated service occupying the port is never killed.
+
+### Gamepad mode
+
+Gamepad mode forwards a Windows XInput controller into WSL. It exists because
+forwarding a controller with `usbipd` does not work in a default WSL2 setup: the
+stock WSL2 kernel is built without the `xpad` driver, so an attached controller
+is enumerated but never produces a usable input device. Gamepad mode keeps the
+controller on Windows, where the native XInput driver handles it, reads its state
+on the Windows side, and streams that state through the same bridge used for
+serial forwarding. Inside WSL a helper, which uses only the Python standard
+library, turns the state into a Linux evdev `input_event` stream describing a
+Microsoft X-Box 360 pad, identified by USB vendor 0x045e and product 0x028e.
+
+The controller must be visible to Windows XInput. If the controller has been
+bound or attached with `usbipd`, Windows no longer owns it and XInput reports no
+controller; unbind it from `usbipd` so that Windows holds the controller before
+using gamepad mode.
+
+Gamepad mode provides two tiers. Both emit the identical evdev byte stream, so a
+single reader works against either, and com2tty itself never requires elevated
+privileges at run time.
+
+#### Default tier: the /tmp event stream
+
+The default tier writes the evdev event stream to a FIFO under `/tmp`, by default
+`/tmp/com2pad0`, and requires no privileged setup.
+
+```cmd
+com2tty --gamepad
+```
+
+A consumer inside WSL reads 24-byte Linux `input_event` records from the FIFO and
+interprets them using the device profile below. This tier is suited to programs
+that read the stream directly. Standard applications and game engines that
+enumerate `/dev/input` devices do not read a FIFO and require the uinput tier.
+
+#### Opt-in tier: a real device through /dev/uinput
+
+The opt-in tier creates a real system-wide device under `/dev/input` so that SDL2
+applications, emulators, and tools such as `evtest` recognise a normally attached
+controller.
+
+```cmd
+com2tty --gamepad --uinput
+```
+
+If `/dev/uinput` is not accessible, com2tty prints the one-time setup instructions
+and automatically falls back to the `/tmp` event stream so that forwarding
+continues to work.
+
+#### One-time setup for the uinput tier
+
+Creating a real input device requires access to `/dev/uinput`, which Linux
+restricts to `root`, and reading the resulting `/dev/input/event*` node requires
+membership of the `input` group. Both are granted once, inside WSL, and com2tty
+still runs without privileges thereafter. Either use `sudo`, or run the commands
+as root from Windows with `wsl -u root`, which requires no password.
+
+```bash
+sudo modprobe uinput
+sudo chmod 0666 /dev/uinput
+sudo usermod -aG input "$USER"
+```
+
+The permission granted by `chmod` does not survive `wsl --shutdown`. To make it
+persist, add a boot command to `/etc/wsl.conf`, which runs as root on every WSL
+start.
+
+```ini
+[boot]
+command = modprobe uinput && chmod 0666 /dev/uinput
+```
+
+After editing `/etc/wsl.conf`, run `wsl --shutdown` once from Windows. This also
+refreshes the group membership granted by `usermod`.
+
+The stock WSL2 kernel sets `CONFIG_INPUT_UINPUT` as a module, which works, but
+does not set `CONFIG_INPUT_JOYDEV`. As a result the legacy `/dev/input/js*` node
+is absent. This is not a problem for modern applications and SDL2, which read
+`/dev/input/event*` directly.
+
+#### Verifying the uinput tier
+
+With com2tty running in `--uinput` mode, confirm the device inside WSL with
+`evtest`.
+
+```bash
+sudo apt install evtest
+evtest
+```
+
+Select the Microsoft X-Box 360 pad device, then move the sticks and press buttons
+on Windows and observe the events appear in WSL.
+
+#### Device profile
+
+Both tiers emit the same evdev codes. Buttons are reported as `BTN_A`, `BTN_B`,
+`BTN_X`, `BTN_Y`, `BTN_TL`, `BTN_TR`, `BTN_SELECT`, `BTN_START`, `BTN_THUMBL`,
+`BTN_THUMBR`, and `BTN_MODE` for the Guide (Xbox logo) button. The sticks are
+reported as `ABS_X` and `ABS_Y` for the left
+stick and `ABS_RX` and `ABS_RY` for the right stick, each spanning the signed
+16-bit range. The triggers are reported as `ABS_Z` for the left trigger and
+`ABS_RZ` for the right trigger, each spanning 0 to 255. The directional pad is
+reported as `ABS_HAT0X` and `ABS_HAT0Y` with values of -1, 0, or 1. The stick Y
+axes are inverted to follow the Linux convention in which pushing up produces a
+negative value.
+
+In the uinput tier the virtual pad also advertises `FF_RUMBLE` force
+feedback. When a game or emulator inside WSL plays a rumble effect, the
+effect's magnitudes travel back through the bridge to the Windows host, which
+drives the physical controller's motors through `XInputSetState`. The strong
+(left, low-frequency) and weak (right, high-frequency) motors map directly to
+their XInput counterparts. The `/tmp` stream tier has no reverse channel and
+therefore no force feedback.
+
+The forwarded signal matches a real controller at the level of these event codes,
+ranges, and resolutions, but it is not bit-for-bit identical to a controller
+driven by the kernel `xpad` driver. The timing and latency differ because the
+path is polled and piped rather than delivered by a fixed USB interrupt interval.
+The Guide button is read through the undocumented `XInputGetStateEx` call and is
+reported as zero on systems where only the legacy `xinput9_1_0` DLL is
+available. These differences are inherent to the approach.
+
+## Architecture overview
+
+The package is organised around a host process on Windows and a helper process
+inside WSL connected by the standard input and output streams of the helper.
+
+`cli.py` parses the command line (after `profiles.py` expands any `@profile`
+tokens) and dispatches to an entry function in `host.py`: `run_bridge` in
+serial mode, `run_multi_bridge` when several ports are given, and
+`run_gamepad_bridge` in gamepad mode. `discovery.py` implements `--list`.
+`__main__.py` and the console entry point both call `cli.main`, and
+`__init__.py` holds the package version.
+
+`host.py` is the Windows side. In serial mode `run_bridge` opens the COM port with
+`pyserial`, spawns the WSL helper with `wsl python3 -u bridge.py`, and runs three
+threads: one relays bytes from the COM port to the helper's standard input, one
+relays bytes from the helper's standard output to the COM port, and one reads the
+helper's standard error. The standard error stream carries a line-oriented control
+protocol whose messages are prefixed with `[CONTROL]`; these messages drive
+dynamic serial-setting changes, the RFC 2217 session lifecycle, and the UF2 upload
+sequence. `host.py` also contains the hot-plug reconnect logic and the routine
+that writes a transferred UF2 image to the correct Windows drive. The board
+detection and reset sequences live in `boards.py`, the UF2 drive lookup and
+AutoPlay suppression in `uf2.py`, and the console colour handling in
+`banner.py`; `host.py` re-exports these names for backwards compatibility.
+
+`bridge.py` is the WSL side for serial forwarding. It creates a pseudo terminal
+with `openpty`, symlinks the requested path to the pseudo-terminal slave, falling
+back to `/tmp` if the requested path is not writable, and runs a `select` loop
+that relays data between the helper's standard input and output and the
+pseudo-terminal master. It also starts the RFC 2217 forwarder thread and the UF2
+relay thread, writes the PlatformIO environment variables into `~/.bashrc`, and
+installs the `picotool` interceptor. `rfc2217_server.py` provides the redirector
+that implements the RFC 2217 protocol for the forwarder.
+
+The gamepad path reuses the same spawn-and-pipe transport. `xinput.py` is the
+Windows side: it polls an XInput controller slot through `ctypes` (preferring
+the `XInputGetStateEx` export so the Guide button is visible) and packs each
+state snapshot into a fixed 16-byte frame, sending a frame only when the state
+changes. `pad_bridge.py` is the WSL side: it parses the frames, translates them
+into evdev events, and writes them to one of two sinks. The default sink writes to
+a `/tmp` FIFO, and the opt-in sink creates a real device through `/dev/uinput`
+using raw `ioctl` calls. Both sinks share the same event-encoding code, so the
+byte stream they produce is identical. In the uinput sink the helper also
+services the kernel's force-feedback upload handshake and streams played
+rumble effects back over its stdout, where the host applies them to the
+physical controller with `XInputSetState`.
+
+For a detailed account of the control protocol, the board reset sequences, the
+reconnection model, the binary frame formats, and the known hardware-unverified
+behaviour, see the [architecture document](ARCHITECTURE.md).
+
+## Development setup
+
+Install the package in editable mode together with the test tools.
+
+```bash
+pip install -e .
+pip install pytest pytest-cov ruff
+```
+
+Run the test suite with coverage, and the linter.
+
+```bash
+pytest --cov=src/com2tty --cov-report=term-missing tests/
+ruff check src tests scripts
+```
+
+A passing run reports all tests passing and full line coverage for the package.
+The test suite is cross-platform. The `tests/conftest.py` file substitutes a mock
+`termios` module on Windows so that the WSL-side modules import for testing, and
+the platform-specific system calls used by the gamepad sinks are mocked so that
+the suite runs on both Windows and Linux.
+
+Continuous integration is defined in `.github/workflows/ci.yml`. It runs a ruff
+lint job and the test suite on `windows-latest` and `ubuntu-latest` against
+Python 3.8 through 3.13, and it enforces 100 percent line coverage by running
+pytest with `--cov-fail-under=100`. A separate job publishes the package to PyPI
+on pushes to the `main` branch.
+
+Because CI has no WSL or serial hardware, a manual end-to-end smoke test lives
+at `scripts/e2e_smoke.py`. Run it on a real Windows host with a device attached
+before a release: it checks `--list`, starts a bridge, verifies the symlink and
+the RFC 2217 forwarder inside WSL, and optionally verifies an echo round-trip
+when the device has TX wired to RX (`--loopback`).
+
+```cmd
+python scripts/e2e_smoke.py --port COM17
+```
+
+## Contributing
+
+Base feature branches on the `develop` branch and open pull requests against it.
+Commit messages follow the Conventional Commits format, for example
+`feat(gamepad): ...` or `test(host): ...`, as established in the project history.
+Every change must keep the test suite passing with 100 percent line coverage on
+both Windows and Ubuntu across the supported Python versions, and must pass the
+ruff linter, because continuous integration enforces both. Add or update tests
+for any behavioural change.
+
+The full contribution process, including how to report bugs, the commit
+convention, the linting requirements, and the manual end-to-end verification
+step, is documented in [CONTRIBUTING.md](CONTRIBUTING.md).
+
+## Troubleshooting
+
+At startup com2tty verifies the WSL environment and reports a specific error if
+a prerequisite is missing. The checks and their remedies are:
+
+- `wsl.exe` is not on `PATH`: install WSL with `wsl --install` from an elevated
+  prompt and reboot if requested.
+- `python3` is not available in the selected distribution: the WSL default
+  distribution may not be a regular Linux distribution (for example
+  `docker-desktop`). List distributions with `wsl -l -v` and either select a
+  suitable one with `--distro`, or install Python inside WSL with
+  `sudo apt install python3`.
+- The bridge script is not readable from WSL: Windows drive automounting is
+  disabled. Ensure `/etc/wsl.conf` does not disable the `[automount]` section,
+  then restart WSL with `wsl --shutdown`.
+
+If the helper reports that the RFC 2217 or UF2 relay port could not be bound,
+another process inside WSL is holding the TCP port. com2tty attempts to clean up
+leftover listeners automatically using `fuser`, which ships in the `psmisc`
+package; on minimal distributions install it with `sudo apt install psmisc`, or
+select a different port with `--rfc2217-port` (the UF2 relay always uses that
+port plus one).
+
+The serial-mode environment variables are written to `~/.bashrc`, to `~/.zshrc`
+when zsh is detected or a `~/.zshrc` file exists, and to
+`~/.config/fish/conf.d/com2tty.fish` when fish is detected. Users of other
+shells must export `PLATFORMIO_UPLOAD_PORT` and `PLATFORMIO_MONITOR_PORT`
+manually.
+
+The startup banner uses ANSI colours only when standard output is an
+interactive terminal that supports them; set the `NO_COLOR` environment
+variable to suppress colours entirely.
+
+If a board is not detected (the banner shows `Unknown`), its USB-UART chip is
+not in the VID whitelist. Check what detection sees with `com2tty --list`, then
+force the board family with `--board` (`esp32`, `pico`, `nrf52`, `samd`, or
+`stm32`) so that reset and upload handling still work.
+
+If the WSL helper reports a permission error while creating the serial symlink,
+the requested path under `/dev` is not writable; the helper falls back to `/tmp`
+and prints the one-time command to link the `/dev` path to it.
+
+If the serial port reports that it is busy or access is denied, ensure no other
+Windows application, such as a serial monitor or a second com2tty instance, is
+holding the COM port open.
+
+If gamepad mode reports all values as zero, Windows XInput is not receiving the
+controller. Confirm the controller is not bound or attached through `usbipd`, so
+that Windows owns it, and confirm it is on the expected XInput slot, which can be
+changed with `--pad-index`.
+
+If the `--uinput` tier cannot open `/dev/uinput`, complete the one-time setup
+described in [Gamepad mode](#gamepad-mode). Until then, com2tty falls back to the
+`/tmp` event stream.
+
+For detailed logs and transfer statistics, run com2tty with `-d` or `--debug`.
+
+```cmd
+com2tty COM3 --debug
+```
+
+## License
+
+This project is licensed under the MIT License. See the [LICENSE](LICENSE) file
+for the full text.