PyTmcStepper 0.7__tar.gz → 0.7.1__tar.gz
This diff represents the content of publicly available package versions that have been released to one of the supported registries. The information contained in this diff is provided for informational purposes only and reflects changes between package versions as they appear in their respective public registries.
- {pytmcstepper-0.7/src/PyTmcStepper.egg-info → pytmcstepper-0.7.1}/PKG-INFO +13 -13
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/README.md +12 -12
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/setup.cfg +1 -1
- {pytmcstepper-0.7 → pytmcstepper-0.7.1/src/PyTmcStepper.egg-info}/PKG-INFO +13 -13
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/LICENSE +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/pyproject.toml +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/PyTmcStepper.egg-info/SOURCES.txt +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/PyTmcStepper.egg-info/dependency_links.txt +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/PyTmcStepper.egg-info/requires.txt +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/PyTmcStepper.egg-info/top_level.txt +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/__init__.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/_tmc_gpio_board.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/_tmc_logger.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/_tmc_math.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/_tmc_stepperdriver.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/com/__init__.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/com/_tmc_com.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/com/_tmc_com_spi.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/com/_tmc_com_uart.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/enable_control/__init__.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/enable_control/_tmc_ec.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/enable_control/_tmc_ec_pin.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/enable_control/_tmc_ec_toff.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/motion_control/__init__.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/motion_control/_tmc_mc.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/motion_control/_tmc_mc_step_dir.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/motion_control/_tmc_mc_step_reg.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/motion_control/_tmc_mc_vactual.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/reg/__init__.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/reg/_tmc2209_reg.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/reg/_tmc220x_reg.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/reg/_tmc224x_reg.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/reg/_tmc_reg.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/tmc_2208.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/tmc_2209.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/tmc_220x.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/src/tmc_driver/tmc_2240.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/tests/test_tmc2209.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/tests/test_tmc2240.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/tests/test_tmc_com_spi.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/tests/test_tmc_com_uart.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/tests/test_tmc_ec_pin.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/tests/test_tmc_math.py +0 -0
- {pytmcstepper-0.7 → pytmcstepper-0.7.1}/tests/test_tmc_move.py +0 -0
|
@@ -1,6 +1,6 @@
|
|
|
1
1
|
Metadata-Version: 2.2
|
|
2
2
|
Name: PyTmcStepper
|
|
3
|
-
Version: 0.7
|
|
3
|
+
Version: 0.7.1
|
|
4
4
|
Summary: This is a Python libary to drive a stepper motor with a Trinamic stepper driver and a single board computer like a Raspberry Pi
|
|
5
5
|
Home-page: https://github.com/Chr157i4n/PyTmcStepper
|
|
6
6
|
Author: Christian Köhlke
|
|
@@ -28,16 +28,16 @@ Requires-Dist: python-periphery; extra == "luckfox-pico"
|
|
|
28
28
|
Provides-Extra: orange-pi
|
|
29
29
|
Requires-Dist: OPi.GPIO; extra == "orange-pi"
|
|
30
30
|
|
|
31
|
-
#
|
|
31
|
+
# PyTmcStepper
|
|
32
32
|
|
|
33
|
-
[](https://pypi.org/project/PyTmcStepper)
|
|
34
|
+
[](https://pypi.org/project/PyTmcStepper)
|
|
35
|
+
[](https://pypi.org/project/PyTmcStepper)
|
|
36
|
+
[](https://GitHub.com/Chr157i4n/PyTmcStepper/issues/)
|
|
37
37
|
|
|
38
38
|
\
|
|
39
39
|
\
|
|
40
|
-
This is a
|
|
40
|
+
This is a Python libary to drive a stepper motor with a Trinamic stepper driver and a single board computer like a Raspberry Pi.
|
|
41
41
|
|
|
42
42
|
This code is still experimental, so use it on your own risk.
|
|
43
43
|
|
|
@@ -56,14 +56,14 @@ Well, the Pi receives 4 bytes from itself and 8 bytes from the driver. So the Pi
|
|
|
56
56
|
The Documentation of the TMC2209 can be found here:
|
|
57
57
|
[TMC2209 - Datsheet](https://www.analog.com/media/en/technical-documentation/data-sheets/TMC2209_datasheet_rev1.09.pdf)
|
|
58
58
|
|
|
59
|
-
The code is also available on [PyPI](https://pypi.org/project/
|
|
59
|
+
The code is also available on [PyPI](https://pypi.org/project/PyTmcStepper).
|
|
60
60
|
|
|
61
61
|
## Installation
|
|
62
62
|
|
|
63
63
|
### Installation with PIP
|
|
64
64
|
|
|
65
65
|
```shell
|
|
66
|
-
pip3 install
|
|
66
|
+
pip3 install PyTmcStepper
|
|
67
67
|
```
|
|
68
68
|
|
|
69
69
|
### Installation with GIT
|
|
@@ -71,7 +71,7 @@ pip3 install TMC-2209-Raspberry-Pi
|
|
|
71
71
|
- clone this repo to your Raspberry Pi using
|
|
72
72
|
|
|
73
73
|
```shell
|
|
74
|
-
git clone https://github.com/Chr157i4n/
|
|
74
|
+
git clone https://github.com/Chr157i4n/PyTmcStepper
|
|
75
75
|
```
|
|
76
76
|
|
|
77
77
|
- install the required modules
|
|
@@ -103,7 +103,7 @@ Those libraries are needed for this library to work. You can either install the
|
|
|
103
103
|
You can also install the needed GPIO library by specifing the Installation Parameter while installing this library:
|
|
104
104
|
|
|
105
105
|
```shell
|
|
106
|
-
pip3 install
|
|
106
|
+
pip3 install PyTmcStepper[RASPBERRY_PI]
|
|
107
107
|
```
|
|
108
108
|
|
|
109
109
|
## Driver Support
|
|
@@ -268,7 +268,7 @@ tmc.set_motor_enabled(False)
|
|
|
268
268
|
|
|
269
269
|
## Troubleshoot
|
|
270
270
|
|
|
271
|
-
If you have questions please check out the [Wiki](https://github.com/Chr157i4n/
|
|
271
|
+
If you have questions please check out the [Wiki](https://github.com/Chr157i4n/PyTmcStepper/wiki) and the other issues.
|
|
272
272
|
|
|
273
273
|
If you encounter any problems, feel free to open an issue (ENG/GER).
|
|
274
274
|
Please don't send any E-Mails to me. Pls use Github, so that i don't need to answer the same question multiple times.
|
|
@@ -297,6 +297,6 @@ The main focus for this are Test setups, as Python is not fast enough for high m
|
|
|
297
297
|
|
|
298
298
|
## Feedback/Contributing
|
|
299
299
|
|
|
300
|
-
If you encounter any problem, feel free to open an issue on the Github [issue page](https://github.com/Chr157i4n/
|
|
300
|
+
If you encounter any problem, feel free to open an issue on the Github [issue page](https://github.com/Chr157i4n/PyTmcStepper/issues).
|
|
301
301
|
Feedback will keep this project growing and I encourage all suggestions.
|
|
302
302
|
Feel free to submit a pull request on the dev branch.
|
|
@@ -1,13 +1,13 @@
|
|
|
1
|
-
#
|
|
1
|
+
# PyTmcStepper
|
|
2
2
|
|
|
3
|
-
[](https://pypi.org/project/PyTmcStepper)
|
|
4
|
+
[](https://pypi.org/project/PyTmcStepper)
|
|
5
|
+
[](https://pypi.org/project/PyTmcStepper)
|
|
6
|
+
[](https://GitHub.com/Chr157i4n/PyTmcStepper/issues/)
|
|
7
7
|
|
|
8
8
|
\
|
|
9
9
|
\
|
|
10
|
-
This is a
|
|
10
|
+
This is a Python libary to drive a stepper motor with a Trinamic stepper driver and a single board computer like a Raspberry Pi.
|
|
11
11
|
|
|
12
12
|
This code is still experimental, so use it on your own risk.
|
|
13
13
|
|
|
@@ -26,14 +26,14 @@ Well, the Pi receives 4 bytes from itself and 8 bytes from the driver. So the Pi
|
|
|
26
26
|
The Documentation of the TMC2209 can be found here:
|
|
27
27
|
[TMC2209 - Datsheet](https://www.analog.com/media/en/technical-documentation/data-sheets/TMC2209_datasheet_rev1.09.pdf)
|
|
28
28
|
|
|
29
|
-
The code is also available on [PyPI](https://pypi.org/project/
|
|
29
|
+
The code is also available on [PyPI](https://pypi.org/project/PyTmcStepper).
|
|
30
30
|
|
|
31
31
|
## Installation
|
|
32
32
|
|
|
33
33
|
### Installation with PIP
|
|
34
34
|
|
|
35
35
|
```shell
|
|
36
|
-
pip3 install
|
|
36
|
+
pip3 install PyTmcStepper
|
|
37
37
|
```
|
|
38
38
|
|
|
39
39
|
### Installation with GIT
|
|
@@ -41,7 +41,7 @@ pip3 install TMC-2209-Raspberry-Pi
|
|
|
41
41
|
- clone this repo to your Raspberry Pi using
|
|
42
42
|
|
|
43
43
|
```shell
|
|
44
|
-
git clone https://github.com/Chr157i4n/
|
|
44
|
+
git clone https://github.com/Chr157i4n/PyTmcStepper
|
|
45
45
|
```
|
|
46
46
|
|
|
47
47
|
- install the required modules
|
|
@@ -73,7 +73,7 @@ Those libraries are needed for this library to work. You can either install the
|
|
|
73
73
|
You can also install the needed GPIO library by specifing the Installation Parameter while installing this library:
|
|
74
74
|
|
|
75
75
|
```shell
|
|
76
|
-
pip3 install
|
|
76
|
+
pip3 install PyTmcStepper[RASPBERRY_PI]
|
|
77
77
|
```
|
|
78
78
|
|
|
79
79
|
## Driver Support
|
|
@@ -238,7 +238,7 @@ tmc.set_motor_enabled(False)
|
|
|
238
238
|
|
|
239
239
|
## Troubleshoot
|
|
240
240
|
|
|
241
|
-
If you have questions please check out the [Wiki](https://github.com/Chr157i4n/
|
|
241
|
+
If you have questions please check out the [Wiki](https://github.com/Chr157i4n/PyTmcStepper/wiki) and the other issues.
|
|
242
242
|
|
|
243
243
|
If you encounter any problems, feel free to open an issue (ENG/GER).
|
|
244
244
|
Please don't send any E-Mails to me. Pls use Github, so that i don't need to answer the same question multiple times.
|
|
@@ -267,6 +267,6 @@ The main focus for this are Test setups, as Python is not fast enough for high m
|
|
|
267
267
|
|
|
268
268
|
## Feedback/Contributing
|
|
269
269
|
|
|
270
|
-
If you encounter any problem, feel free to open an issue on the Github [issue page](https://github.com/Chr157i4n/
|
|
270
|
+
If you encounter any problem, feel free to open an issue on the Github [issue page](https://github.com/Chr157i4n/PyTmcStepper/issues).
|
|
271
271
|
Feedback will keep this project growing and I encourage all suggestions.
|
|
272
272
|
Feel free to submit a pull request on the dev branch.
|
|
@@ -1,6 +1,6 @@
|
|
|
1
1
|
[metadata]
|
|
2
2
|
name = PyTmcStepper
|
|
3
|
-
version = 0.7
|
|
3
|
+
version = 0.7.1
|
|
4
4
|
author = Christian Köhlke
|
|
5
5
|
author_email = christian@koehlke.de
|
|
6
6
|
description = This is a Python libary to drive a stepper motor with a Trinamic stepper driver and a single board computer like a Raspberry Pi
|
|
@@ -1,6 +1,6 @@
|
|
|
1
1
|
Metadata-Version: 2.2
|
|
2
2
|
Name: PyTmcStepper
|
|
3
|
-
Version: 0.7
|
|
3
|
+
Version: 0.7.1
|
|
4
4
|
Summary: This is a Python libary to drive a stepper motor with a Trinamic stepper driver and a single board computer like a Raspberry Pi
|
|
5
5
|
Home-page: https://github.com/Chr157i4n/PyTmcStepper
|
|
6
6
|
Author: Christian Köhlke
|
|
@@ -28,16 +28,16 @@ Requires-Dist: python-periphery; extra == "luckfox-pico"
|
|
|
28
28
|
Provides-Extra: orange-pi
|
|
29
29
|
Requires-Dist: OPi.GPIO; extra == "orange-pi"
|
|
30
30
|
|
|
31
|
-
#
|
|
31
|
+
# PyTmcStepper
|
|
32
32
|
|
|
33
|
-
[](https://pypi.org/project/PyTmcStepper)
|
|
34
|
+
[](https://pypi.org/project/PyTmcStepper)
|
|
35
|
+
[](https://pypi.org/project/PyTmcStepper)
|
|
36
|
+
[](https://GitHub.com/Chr157i4n/PyTmcStepper/issues/)
|
|
37
37
|
|
|
38
38
|
\
|
|
39
39
|
\
|
|
40
|
-
This is a
|
|
40
|
+
This is a Python libary to drive a stepper motor with a Trinamic stepper driver and a single board computer like a Raspberry Pi.
|
|
41
41
|
|
|
42
42
|
This code is still experimental, so use it on your own risk.
|
|
43
43
|
|
|
@@ -56,14 +56,14 @@ Well, the Pi receives 4 bytes from itself and 8 bytes from the driver. So the Pi
|
|
|
56
56
|
The Documentation of the TMC2209 can be found here:
|
|
57
57
|
[TMC2209 - Datsheet](https://www.analog.com/media/en/technical-documentation/data-sheets/TMC2209_datasheet_rev1.09.pdf)
|
|
58
58
|
|
|
59
|
-
The code is also available on [PyPI](https://pypi.org/project/
|
|
59
|
+
The code is also available on [PyPI](https://pypi.org/project/PyTmcStepper).
|
|
60
60
|
|
|
61
61
|
## Installation
|
|
62
62
|
|
|
63
63
|
### Installation with PIP
|
|
64
64
|
|
|
65
65
|
```shell
|
|
66
|
-
pip3 install
|
|
66
|
+
pip3 install PyTmcStepper
|
|
67
67
|
```
|
|
68
68
|
|
|
69
69
|
### Installation with GIT
|
|
@@ -71,7 +71,7 @@ pip3 install TMC-2209-Raspberry-Pi
|
|
|
71
71
|
- clone this repo to your Raspberry Pi using
|
|
72
72
|
|
|
73
73
|
```shell
|
|
74
|
-
git clone https://github.com/Chr157i4n/
|
|
74
|
+
git clone https://github.com/Chr157i4n/PyTmcStepper
|
|
75
75
|
```
|
|
76
76
|
|
|
77
77
|
- install the required modules
|
|
@@ -103,7 +103,7 @@ Those libraries are needed for this library to work. You can either install the
|
|
|
103
103
|
You can also install the needed GPIO library by specifing the Installation Parameter while installing this library:
|
|
104
104
|
|
|
105
105
|
```shell
|
|
106
|
-
pip3 install
|
|
106
|
+
pip3 install PyTmcStepper[RASPBERRY_PI]
|
|
107
107
|
```
|
|
108
108
|
|
|
109
109
|
## Driver Support
|
|
@@ -268,7 +268,7 @@ tmc.set_motor_enabled(False)
|
|
|
268
268
|
|
|
269
269
|
## Troubleshoot
|
|
270
270
|
|
|
271
|
-
If you have questions please check out the [Wiki](https://github.com/Chr157i4n/
|
|
271
|
+
If you have questions please check out the [Wiki](https://github.com/Chr157i4n/PyTmcStepper/wiki) and the other issues.
|
|
272
272
|
|
|
273
273
|
If you encounter any problems, feel free to open an issue (ENG/GER).
|
|
274
274
|
Please don't send any E-Mails to me. Pls use Github, so that i don't need to answer the same question multiple times.
|
|
@@ -297,6 +297,6 @@ The main focus for this are Test setups, as Python is not fast enough for high m
|
|
|
297
297
|
|
|
298
298
|
## Feedback/Contributing
|
|
299
299
|
|
|
300
|
-
If you encounter any problem, feel free to open an issue on the Github [issue page](https://github.com/Chr157i4n/
|
|
300
|
+
If you encounter any problem, feel free to open an issue on the Github [issue page](https://github.com/Chr157i4n/PyTmcStepper/issues).
|
|
301
301
|
Feedback will keep this project growing and I encourage all suggestions.
|
|
302
302
|
Feel free to submit a pull request on the dev branch.
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|
|
File without changes
|